Elitech Temperature Data Logger RC-5+ and RC-5+ TE

[@Famdoc1000]

I purchased the RC5+ for continuous temperature monitoring for storage of COVID vaccine, as required by the CDC and the NYCDOH. I am quite satisfied with the device, found its set-up process relatively easy, accompanied by this video and am able to upload data for submission to my health department.

[@ElitechTechnologyInc]

Hi, we really appreciate your feedback. Any problems, please contact us freely.

[@windkl]

Extraordinary device with exceptional accuracy in measurements!

[@SonicOrbStudios]

Love these for diagnostic in refrigerators at my apartment complex

[@vincebush]

I could not find the Thermal Time Constant info on any data sheet so I took a chance and purchased one. I measured a whopping 8 minute Time Constant. It take 40 minutes to reach a new temperature. FAR too slow for what I need so I returned it.

[@unionse7en]

any way too download csv data to a mobile phone in the field, rather than a laptop?

[@starhopper457]

I now have one and so far love it. A question though - can it store more than one program and then I pick which one to run? I may need it for an astronomical event where I may not have immediate access to a computer to adjust things, so having multiple templates would be nice.

[@anaisabelazevedogregorio9538]

good morning Is it possible for the data logger to connect to the USB port and immediately open a window with the report, without the need for this computer to have Elitech software? At my work, the computers do not allow you to install software outside the service. I wanted to use this data logger to monitor a vaccine refrigerator. thanks

[@Neinei0913]

hello, device shows 6/21/2021, how to change to current date and time? thanks

[@Carla-hq6yp]

Does the RC-5+ have a Bluetooth option to retrieve temperature log?

[@cwilliams9400]

Should I leave it in the fridge and it will regularly monitor the temp?

[@ElitechTechnologyInc]

Hi, that's right! The logging interval can be set in our free software according to your preference.

[@MohamedAhmed-nh6ef]

Is this data logger reusable or it will log for certain period then it life end like 60 days or 90 days logger ?

[@Carla-hq6yp]

Do you have a Elitech temperature logger/device with a Bluetooth option?

[@PaulaAndreaAriasArellano]

Hello, I need help, the pause and play symbols appear on the LCD screen of the RC5+ at the same time. How can it be removed to start recording data???

[@ronkloiber]

Hello, I have the RC-5+ I am able to start recording after I have set the parameters in software, but if I stop the recording, I am not able to start it again without saving parameters to it again. Is this normal? if not, how can I start and stop multiple times? Does it append to an existing log, or start a new file?

[@auniesakinahh3030]

sorry hi , how to set up the date .

[@ElitechTechnologyInc]

Hi! To setup the data and time, please connect the device to your computer, open the software ElitechLog. Go to Parameter, and select the correct time zone and click Save Parameter in the end. If the time zone setting field is greyed out, please click Save Parameter directly, it will sync to your computer time automatically.

[@windkl]

Could you provide info about the response time of temperature measurements?

[@ElitechTechnologyInc]

The display screen refreshes the temperature once in about 3-5 seconds.

[@ronaldreuling6103]

40 minutes

[@DIVA17MARIAN]

Hello I have a question about the Calibration (temperature) parameter, how to use it?

[@ElitechTechnologyInc]

An offset (not slope) calibration is possible using the RC-5 software. With the device connected to a USB port (and the software permitted to "make changes to this computer" despite the "unknown publisher" or missing certificate): Click "Parameter Set" (in toolbar or Settings menu), then enter the required delta (negative to decrease the reading) as "TemperatureCalibration" near the bottom of the second column, then click button "Save Parameter", confirm and Exit. Note that although the Up/Down arrow buttons change the offset by a full degree, you can edit to the displayed resolution of 0.1°. For any further questions, you may have a look Elitech FAQ part.

[@coolmonkey619]

Hi can I use this as a stand alone room sensor.

[@ElitechTechnologyInc]

Hi, sure, they canwork as room temperature monitors.

[@meme-mm2wp]

Hi, is the device can be calibrated?

[@ElitechTechnologyInc]

Yes, you could send the unit to your local calibration center for the re-calibration service.

[@caslamdq]

How do I have to set the parameters to get an hour-by-hour daily record during a month?

[@ElitechTechnologyInc]

Hi! Are you trying to set the logging interval to 1 hour? If so, please connect the device to your computer, open the software ElitechLog, go to Parameter, find Logging Interval and set it to 1 hour 0 min 0 sec. Click Save Parameter in the end. Then you device will be ready to start a new logging with 1-hour recording interval.

[@caslamdq]

@@ElitechTechnologyInc Hi, thanks for your answer!. Yes, I have set the logging interval to 1 hour. However, it recorded during 6 days and wrote one register. Thus, I have just one temp Max and Min. What I need is a daily record with its Max and Min records. Is this possible?.

[@caslamdq]

@@ElitechTechnologyInc Hi, thanks for your answer. What I need is to get a daily record with its Max And Min Temp for at least 1 month.

[@cburshtein]

I just got mine but it's showing NC and the play+stop icon are on and off constantly. It doesn't start when the play button is pressed for 5 seconds. Where can I get assistance?

[@ElitechTechnologyInc]

Hi Cecilia, the NC message appears with two possible reasons. One is the temperaure is out of the measurement range. Another one is the sensor issue. You may contact our support team via [e-mail]

[@windkl]

probably it is configured through the app to "external" sensor type. You need to change the sensor to "internal" .

[@cburshtein]

@@windkl It was not, it continued to go off and on randomly.

[@windkl]

@@cburshtein I see. Then it's definitely defective.

[@muhammadarfanulaziz1507]

it can be submerge in liquid for 24 hour?

[@ElitechTechnologyInc]

Hi Arfanual! No, they cannot be submerged into the liquid.

[@ablosport312]

Can it measure temperature from +2 to +8°c?

[@ElitechTechnologyInc]

Hi, yes, the measurement of RC-5+ and RC-5+ TE is both -30°C~+70°C.

[@ablosport312]

@@ElitechTechnologyInc thank you very much..

[@FB-gm6el]

i wish things like "low battery!" and "recording in process" were a bit clearer/more intuitive...

[@rajkumars9867]

Avalible in low cast any one u want contact me