End Of Day 2010 Cadillac SRX No Crank No Start

[@todd7831]

This is perfect video step by step was exactly same as my car and guess what guy who put motor in didn't fully toghten ground to block. Somehow car did run for months then every once in awhile wouldn't do anything. Mine is cts but same thing all tests allowed me to pinpoint my issue even all described symptoms were the same

[@caddi_headquarters9496]

Very good video. Less talking and straight to the point.

[@arthurfricchione8119]

Brian I think you need a laser pointer for Christmas. Think it would be helpful pointing things out. Hey you never know. Stay safe and well 👍🇺🇸

[@davidwagner3356]

Brian, I'm glad you mentioned about the fiesta TCM. Did my first one today and just couldn't figure it out. Even though I could retrieve codes and see Data when I would program IDS would say unable to communicate. Was able to update the PCM without any issues. I was even able to perform the TR relearn on the TCM to be able to start the vehicle, but can't seem to program.

[@BrianMann216]

Was this new or used?

[@davidwagner3356]

@@BrianMann216 first when I got there they had a used one installed and IDS said to program a blank computer so I told them it had to be new and I still had a problem when they got me a brand new one from the dealer.

[@williamdaniels2946]

@ 5:35 of your awesome straight to the point video what did you ground to besides the negative cable you had hooked up, was it just the one negative cable you used or did you use both negatives

[@BrianMann216]

I believe i had jumped the ground from the battery to the engine block with the jumper cables.

[@williamdaniels2946]

@ thank you so much and may 2025 bring nothing but awesomeness because that’s what you are my bratha man

[@7minnow]

Mr B your the best! love the glasses thought green tint. Just throwing it out there, you do you. Green/blue/red yellow/black Hallmark

[@BrianMann216]

The frames are green no tint just the lighting.LOL

[@CarpeDiem-ut1xi]

Hey. Can you help me with a diagram for the 2010 Cadillac srx4? I’m getting a P062B code. But I realized very low voltage if I ground probe at the pcm case. Just want to test the grounds coming into the pcm. Thanks.

[@oscarcee6831]

I have a 2012 cadillac srx with a u0100 how would you take staeps to dignose that type of code ?

[@anthonyjennings8830]

to find the grounds faster in identifix, if that is specifically what your after click ground distribution instead of engine controls

[@BrianMann216]

Thanks for thr pointer I will try this out.. always looking for more efficient ways..

[@detailedautodiagnostics]

Another really good video my friend!!!

[@BrianMann216]

Thanks for watching! These problems keep us on our toes!

[@rrmech11]

Nice job Brian

[@crystalwhite7291]

My husband has a 2010 Cadillac SRX that he got from a lady the she Siam that she drove it to the store in came back out in the battery was dead so her husband went to go get a new battery in she drove home came back out the next day in push the button in the lights are on but only get a click every time so my husband got it in change the starter instead of the same click every time you push the button do you have any idea what could it be?

[@BrianMann216]

Could me many things, what codes are setting?

[@berdiabd274]

hello, can you help me with a 2010 cadillac srx. The car stalled while I was driving and won't start. high beam lamps, turn signals are not lit, the trunk does not open, the horn signal does not work and the car simply does not start. what could be the problem?

[@berdiabd274]

when you press start, there is no sound that the starter turns and the control panel goes out

[@whylietv2066]

I got the same problem did u find a solution

[@whylietv2066]

?

[@Yukonjackman1]

Nicely stated and Done.

[@anthonyburley3021]

What if you had a new motor put in a 2012 srx but the push start sounds like it’s stuck and want crank

[@BrianMann216]

Make sure no accessories pulleys are stuck,

[@gilbertomoran7420]

Hi Brian , i have a 2012 Toyota highlander thats kicking my butt . Its an antitheft issue . All keys got erased form the certification ecu, vehicle came in no start . Checked data ecu and found 0 keys programmed. After diag found certification ecu at fault . Tried all keys lost with used ecu but got error . Am I missing something when it comes to programming used ecu ? Or should i just go with a new certification ecu ? Sorry for high jack your comment section . Any help would be greatly appreciated.

[@BrianMann216]

I am not sure if the ecu needs recomunicated. Thanks the reset between the key reader and the ecm. After that relearn the keys?

[@detailedautodiagnostics]

I would make sure that the used ecm has communications and all functions without the programmed keys before you move on....this will help you narrow down your trouble tree

[@gilbertomoran7420]

Thank you guys , i do have comms with the certification ecu . The used one i got had 2 keys programmed previously (shown in data) I tried to do a ecu reset (16min procidure) but got an error . So i swapped the s93c86 eprom(holds key data) from module to module . In the process i think I overheated the eprom because now both modules show 0 keys programmed. I got abother used certification module on the way , this time ill try to the the "ecu communication id reset " and see if that mates all 3 . ecm , id box and certification ecu . 🤞 . Any other suggestions?

[@BrianMann216]

@@gilbertomoran7420 keep us posted

[@SuperBeetle1600]

Did they end up fixing the ground or ran a new one?

[@BrianMann216]

Not sure , needs to be put on a lift, it was in the street!

[@karaokejunkies88]

The technician that installed the engine left one of the main battery grounds unhooked and sitting on the subframe

[@BrianMann216]

@@karaokejunkies88 thanks for letting me know!!

[@karaokejunkies88]

No problem. We are still giving him shit about it. Lol

[@MiguelRodriguez-go5mb]

Are u in Cleveland Ohio?

[@BrianMann216]

Yes

[@cliff499]

Any luck on that ficm in the salt mine truck ?

[@BrianMann216]

Not yet , I sent the module out for inspection / testing... AND it is not bad!! So i am going to have to schedule a trip for more testing once i get the module back... I thinking to overlay a can bus for ECM TCM FCIM and GPCM.

[@cliff499]

@@BrianMann216 it can never be easy or just give us a break. I recently did a bcm on a 2020 f350. Couldn’t finish programming due to TPMS issues. Of course all sensors are good and RFA is good. Even get the training completed message. So another bcm it is 🤣

[@Inks505]

Dude I don't care how technical you get that scanner you could of showed at least one time when you first tried to crank it how it sounded

[@عليمحمد-ر8ز3ج]

Nice job 👍👍👍👍

[@darnellaustin2845]

Are you in Cleveland ohio

[@BrianMann216]

Yes I am

[@billsmith2212]

Auction usually means TROUBLE ! They only use the best techs - escaped cons !

[@rosieclark3661]

Another typical good old fashioned GM American 🇺🇸 expensive wheelbarrow !!!

[@rosieclark3661]

Get rid of it and buy a Honda or Toyota problem solved

[@BrianMann216]

I agree honda and toyota have been the best quality vehicles

[@mikhailsmith7585]

I got the same similar problem please contact me if you can