Thank you! Finally a video that shows the head removal. This is what I needed.
@masterprintersupport27998 жыл бұрын
Maintenance tip:The problem is that inside the PiezoFilm there is a specific resistance that the type of ink.For example solvent resistance tfp printhead is different than the waterbase printhead for subli/pigments/and various aqua inks.I want to tell you that the recover maintenance has different effect because of the ink type you use.Also do not forget that:Epson does not recomment the flash procedure in order of course to sell printheads.The ink selector is also good to clean or change after cleaning the printhead.Service program also is important to set up the head rank id for better perfomance-it corrects the voltage in order to work more stable with correct khz cycle.(important).
This was a gem amongst the Epson printheads cleaning videos! I just wanted to know how to remove the head and you answered! Thanks again
@KenBurtch3 жыл бұрын
I just did this on a P7000, which looks the same but definitely isn't exactly the same. I have nothing against the author of the video. It was great to see how to get to the print head and what to do. Having said that, I wish bodily harm on the engineer who designed the assembly. I had 8 screws to remove, and then the fun began. The outer assembly is also tethered by wires on the right hand side, so I couldn't just swing it out of the way. Had to suspend it above like I would a brake caliper. This makes it difficult to get to the top screws of the print head, but I got them out. I had the syringe and a cup, but also needed a small piece of tubing to connect the syringe to the nozzle. When you're flushing fluid back through the head, remember to pull the syringe back a bit before you remove it, or the pressure makes the fluid go everywhere. Once it was time to reassemble, remember to connect the ribbon cables before putting the print head back in, and a pair of needle nose pliers helped me get them in. I could not get the top right screw into the print head and you're a better man than me if you can. :) Somehow I got all 8 outer screws back in. Fired it up, did a heavy cleaning, and a nozzle check. Green and LC are still clogged, so must be something in the lines. Either way, told my boss we'll need a new one once the quality gets bad enough, as the print head is about 3/4 the cost of a new machine. Just glad I survived. Best of luck out there!
Hey I have a couple clogged nozzles yellow and magenta tried piezo flush , removed the head and flushed it as well , cleaned the capping station any suggestions
@bahot4544 ай бұрын
I did this now it prints blank pages. What to do?! Anyone got the service program?
@veryheavymetals4 жыл бұрын
There are more then 5 screws (at least in my 7900!) A couple were "hidden" under some "flaps".
@luigiulisseiovane3 жыл бұрын
It works? I have a problem with green nozzle and I wanted to use this procedure to clean it.
@veryheavymetals3 жыл бұрын
@@luigiulisseiovane nope. The printer ended up being scrapped.
@rociodealba2 жыл бұрын
Hi Felipe. Bravo on this video! I have one question. I bent the flat cables you mentioned. I need to replace them. Do you know what they are called and where I can get them?
@alipixproductions43162 жыл бұрын
following
@bobnoyes76042 жыл бұрын
Thanks for the video! Is this the same procedure for the 9900?
@awonisebankole14092 жыл бұрын
I did exactly this but the magenta isn't coming through. Other colours are perfect. Please any help
@mellosays7 жыл бұрын
Obrigado pela instrucao, mas qual o fluido que voce usa para limpar?
@sublimas16672 жыл бұрын
hello felipe good day a question, if I change the head to the epson stylus pro 9700 and what do you do? Could you tell me what procedure I have to do when I put the new head? I would greatly appreciate it
@westgramercy210210 жыл бұрын
Liquid us its called cleaning solution for wide format printers..can get it at any sublimation supplys
@a.valente68215 ай бұрын
Thanks for your video! My Epson 9900 prints correctly in color, but when I print in B&W it prints in brown magenta tone. Epson's authorized service technician checked the printer through software and mechanically; we changed all the original black inks (Photo Black, Matte Black, Light Black and Light Light Light Black), but I still have the same problem, could you please tell me what could be the cause and how can I solve it? Thank you very much
@roshan40416 жыл бұрын
On my Epson 9890 there is one more screw lower down that I had to remove to get access to the print head
@johnmaddock23706 жыл бұрын
Where at? I have the same unit. thank you!
@kennethscheinberg1673 жыл бұрын
what is the yellow attachment to the syringe when cleaning the 7900 printhead. I also dropped one of the printhead attachment screws. Where can I get a replacement?
@welitonvital7 жыл бұрын
interessante. esse procedimento de limpesa se aplica a outras cabeças, tipo da 1110? e que solução vcs estao usando? obrigado
@danielaraoz9375 жыл бұрын
Hola es el mismo sistema para la EPSON 7800?
@Tyfonsasa9 жыл бұрын
Obrigado Felipe bem explicado tutorial. por favor, faça mais vídeo. Eu também uso a Epson 9900 se você sabe como repor o contador?
@alexventuree81006 жыл бұрын
Tengo un problema con mi impresora epson9900 con el canal verde que esta parcialmente tapado, pudiste hacer la limpieza?
@LeifermannPatrick6 жыл бұрын
Good luck with the third screw.
@timothymccormick15377 жыл бұрын
What solution did you use? I tried it with a windex and alcohol mixture and it didn't quite fix it.
@matiasguinez38812 жыл бұрын
Hi. How i can remplace one damper Epson 9700? Alguien sabe cómo cambiar el damper de esta impresora? Gracias
@AtifLangrial9 жыл бұрын
on the 9890. where you pointed out the third screw there are 3 screws, two philips+ and one small star *..... could you tell me which it is?
@petermendonce65916 жыл бұрын
Good teaching.. Thanks
@alexventuree81005 жыл бұрын
Peter Mendonce how worked in your printer?
@wdeane63497 жыл бұрын
Nice video Felipe. do you happen to know if this is the same procedure and printerhead for the Epson 9890?
@kevinmiller40936 жыл бұрын
Can anyone tell me where I can find info on removing the print head for cleaning on an Epson sp 9900. Trying to salvage my machine but can't find a tutorial anywhere
@alexventuree81005 жыл бұрын
are you found it?
@wdeane63497 жыл бұрын
Felipe, I have a question about the screw that you are calling screw number 3 in this video. When I look for this screw I see two screws right next to each other. The one on the left looks a little larger than the one on the right. Which of these two screws is actually SCREW NUMBER 3? My name is Walt, owner of a 9890. Thanks for the help!
@VIVAELLCHEE19677 жыл бұрын
I got the same question and I own a 7900.
@kayhandurukan6 жыл бұрын
Left one is your answer, but you can remove both, because the right one is the screw of the print head, that you are going to be removed also
@marciasparks16927 жыл бұрын
is it the same procedure for my Epson 7890?
@Marc-th9xw4 жыл бұрын
Was it... did you do it?
@mohammedmahmoud96516 жыл бұрын
How to change the Bluewater EBS 7880
@kayohayashi94202 жыл бұрын
after removing the print head for cleaning on the epson pro stylus 7900 when I went to install it back in the machine I could get the flat ribbon back into the print head? any advice?
VI QUE ESSE VÍDEO TEM UM CARA FALANDO EM PORTUGUÊS NO FUNDO , PRECISO TROCAR A CORREIA DO CARRINHO DA CABEÇA , GOSTARIA DE UM VÍDEO MOSTRANDO COMO FAZER ISSO . E SE POSSÍVEL EM PORTUGUÊS . OBRIGADO
@oydinsuleymanova52708 жыл бұрын
please help.what can I do,no collors,Epson 9700
@MrAkrapol9 жыл бұрын
how to change wiper cleaner for epson pro 7700
@marienbr9 жыл бұрын
Felipe como eu consigo falar com vc, tenho uma Epson 9880 e estou querendo ajuda, onde consigo o liquido para limpar?Obrigado, onde
@anselmediby94184 жыл бұрын
salut aidé moi a trouver le solvantqu'il utilise car j'ai le meme probleme
@scottwingfield64034 жыл бұрын
Thanks for sharing this. Epson has such poor maintenance information available.
@suibema9 жыл бұрын
que liquido uso D: ??? quiero saber urge :s
@cornishman195410 жыл бұрын
Do you know how to change out the print head on a Epson 9890
@paolopinna31577 жыл бұрын
Please help me after this procedure my epson stilo pro 7700 does not recognize the cartridges there are X in all colors if I remove a color the printer recognizes the other cartridges I have already tried to change the cartridges without resolving
@michaelcruz26216 жыл бұрын
Were you ever able to fix this problem? I have the same issue.
@aaronmorgan24975 жыл бұрын
what is the liquid in the cup ???
@oydinsuleymanova52708 жыл бұрын
hello Mr.fellipe.I do like this video.but problems with dampers maybe
@user-oq6fw1wn5o10 жыл бұрын
thank you
@ladyprintboss4 жыл бұрын
thank you!
@viktorlajtercuk22064 жыл бұрын
Hi, I have Epson Stylus Pro 7900. Because clogged orange and green color, (same as my sister and same printer, ! this is interesting ) I remove printhead, and try clean it. Before cleaning test work without problem only green and orange channel missing. Cleaning was difficult, clogged was also channel when connecting ink cartridge - on back printer, where is some plate with "ink connector" Also I clean all tubes, and dampers on head. After it I look to head, orange and green channel was clogged, any chance to put in clean solution, then I disassembly printhead, where is two screws and can clean "connector" was also clogged and I see that orange and green was dry , clogged. Because cleaning was not possible only to put head in solution I put it to ultrasonic cleaner, only after it channels slowly cleaned. Now head is full clean. BUT, trouble, when I mout all , fill tubes , dampers with ink, printer break with error 1A39 :( By the way it happens me everytime, after clean epson printhead :(. Any advice to this error ? In service manual is problem with printhead by bad connection in align or bad circuit on printhead. Is some solution to measure resistance on printhead connector and some trick to disable short circuit or some else to run printer ? Now printer is a pile of scrap metal :( New printhead is overly expensive and , please some advice to my mail velektronic@gmail.com, many thanks
@po2lony123 Жыл бұрын
You have destroyed the print head with the ultrasonic cleaner. It killed the membrane
@drdarrow8 жыл бұрын
Thank you!
@antoniocarlossilva24424 жыл бұрын
hello I have a print Epson Styllus 7890 I replaced the cartridgeT 636700 ligth black 700 ml original, I was able to print 12 images, now it is showing Cartridge error asking to replace, what can it be? help me please!!
@dragonx1513 жыл бұрын
Did you try maybe resetting the chip with a chip resetter?
@jaimecervantesalvarez63584 жыл бұрын
Al encender no reconoce los cartuchos, alguna solución?
@miltkallu86415 ай бұрын
Quemaste el cabezal y la placa logica. Mejor tira la impresora, te vas a ahorrar dolores de cabeza y plata y tiempo
@deepakkadam87078 жыл бұрын
epson 7890 cloged nozzel problem
@GaryTaylorvw4 жыл бұрын
Hi, I’m my 9900 I removed the 5 you said, still wouldn’t come off, to discover there was 2 more that needed removing , so 7 screws to remove in total to remove the head
@veronicar23724 жыл бұрын
Were the extra 2 on the left, Far behind the black cover? I also removed 2 extras (plus many more), but it doesn’t want to come off. Any advice? Should I just tug it harder?
@thebaconwhisperer143 жыл бұрын
@@veronicar2372 Were you able to get it off?
@danielacaques670910 жыл бұрын
What do you use to clean the prient head?
@tatypintado102310 жыл бұрын
Hi, I was wondering the same question. What do you use to clean it?. If you can help us. THANKS
@stancnet8 жыл бұрын
+Taty Pintado Yes.
@stancnet8 жыл бұрын
+Taty Pintado You need to buy some print head cleaning solution. You can find it on websites that sell refillable carts or Amazon/ebay. It's a late reply but it might help others.
@chrismc4105 жыл бұрын
I've always said if you have to put that much effort to take something off to clean it, you might as well replace that component. In short, if you have to put in that much work to take out the printhead, might as well replace it.
@paulh65914 жыл бұрын
The cost of the print head of this outdated is half the cost of a whole new printer. This video ably describes a great " here goes nothing" thing to do on a printer that was going to be discarded otherwise.
@dewright234 жыл бұрын
On my SC P9000, a new print head is $1,200. If I can take 15 minutes to remove the head, it's worth it
@coffeebean63148 жыл бұрын
Thanks!
@macseeking7 жыл бұрын
Thank you very much. your video saved my life. ^^
@alexventuree81005 жыл бұрын
how worked in your printer?
@lghale195510 жыл бұрын
Thanks for this video I have done the cleaning as you instructed, pulled the solution from the top and then pushed back in to the cup. Reassembled the everything back into machine and machine started back up correctly without any error messages. The only issue I'm having is I tried to print a photo after doing a cleaning and I'm not getting any printing at all nothing, done a nozzle check doesn't print anything. Can you please advise on this matter?
@TiDuZzO7 жыл бұрын
Same problem here, did you find a solution to this? Please, if you found a solution tell us how to solve this :(
@sarareza27397 жыл бұрын
Any idea what went wrong or how you fixed it?
@numberoneprinting62085 жыл бұрын
how you fixed it?
@jodyhaynes93895 жыл бұрын
@@numberoneprinting6208 u need to wet the capping station in cleaner then do a cleaning cycle, its help with suction
@ioan_astro4 жыл бұрын
I am having the same issues, but I can't get it to print....not sure why this is happening, I've done a Init 2 times and still nothing, please help:)
@tropcm6 жыл бұрын
I falow every step as you did it started to give code 4000 Edit: now it says 1A37
@ioan_astro4 жыл бұрын
I had the same problem, you have to reseat the cables and it will go away
@samuelferreira4886 жыл бұрын
Bom dia vocês oferecem serviços no Brasil?
@AaronFruman10 жыл бұрын
Good video guys, but I would be so scared to make a small mistake here. The print head is arguably a $1000 part. Not cheap.
@jaredzafrasalim74347 жыл бұрын
Hello many thanks for uploading videos so great helped me a lot also I subscrivied to your channel is very good I have a great problem of a few days, I'm printing badly I take the plotter to print photos lately I came out with a yellow color in The skin and is much the tone I thought it was because the head was blocked but not when I send the tes all come out well but in the imganes they leave very yellow I hope they can help me with my problem thanks
@BeniaminoGraphicDesign8 жыл бұрын
Ciao, ho un numero sul display chiede l'assistenza 0010 come devo fare?
@aromagidaromatizator787911 жыл бұрын
thank you!!!
@mouseminer29783 жыл бұрын
How much it really cost for a new head? Is Dutaprint.com legitimate seller? Please help. Thanks
@alejandrocerna94236 жыл бұрын
Mucho agradeceré publicar un video como este, pero de la impresora Epson Stylus Pro 9900. Saludos
@alexventuree81006 жыл бұрын
Alejandro Cerna ya conseguiste el tutorial para la epson 9900?
@alejandrocerna94236 жыл бұрын
Hola, aun no lo he conseguido. Saludos
@alexventuree81006 жыл бұрын
tengo problema con el canal del color verde, y no lo he podido arreglar, en que pais estas?
@alejandrocerna94236 жыл бұрын
Hola, estoy en Peru. Lamento decirte que soy nuevo en el asunto, y no creo estar en condición de ayudarte, espero poder estarlo. Saludos
@alexventuree81006 жыл бұрын
Cual es tu problema con la impresora?
@yewondentallab40197 жыл бұрын
I have checked with my Epson 9900 and it is different than what you show here. Would you please show or explain here how to remove printer head on 9900? Thank you and looking forward to hear from you
@alexandrefortier89966 жыл бұрын
Did you find something for your 9900?
@kayhandurukan6 жыл бұрын
you have to remove 7 screws in order to remove the print head. Don't forget the one under the pipes :)
@alexventuree81005 жыл бұрын
how worked the clean in your epson 9900?
@bevmichel87575 жыл бұрын
Kayhan Durukan can you explain exactly where the 9900 screws are?
@fkengmode75163 жыл бұрын
Ça coûte combient
@numberoneprinting62085 жыл бұрын
HELP Nozzle check doesn't print anything. Can you please advise on this matter?
@jodyhaynes93895 жыл бұрын
wet capping station then cleaning cycle the moister help creation suction
@ioan_astro4 жыл бұрын
I have the same problem, did you find any solution?
@reicapixaba8 жыл бұрын
Como destravar o carro da cabeça? A minha não liga.
@hanafigueiredofranca146 жыл бұрын
Oi como vc destravou o carro com ela desligada
@TurkiyeCumhurbaskani7 жыл бұрын
my belt came out from 9890, any tips how to put it back?
@TurkiyeCumhurbaskani7 жыл бұрын
belt that moves the head back and forth
@CreativeunitedMy3 жыл бұрын
I hate this printer. Argh.. replaced new printhead last year.. and it happened again. Yellow missing in some areas. Power clean, SS cleaning still same problem. Planning to manually clean the printhead. If still cannot fix i will throw it at epson HQ! New printhead cost a bomb.
@fidia_temple3 жыл бұрын
ok now my epson said FATAL ERROR: 1A35... it's completly off...cazzo...
@laneimages7 жыл бұрын
Is the removal procedure for the Epson 7890 the same ???
@kayhandurukan6 жыл бұрын
you have to remove 8 screws for 7890
@danielaraoz9375 жыл бұрын
Hola es el mismo procedimiento para la epson 7800?
@romuloanderson9 жыл бұрын
Help! Help me! I do not speak English. I'm from Brazil. can write many sentences, but Write short sentences not write long sentences (not write big sentences) ( PLEASE ) I will use google translation You pull liquid with the syringe? Push or pull?
@andersonlpaixao9 жыл бұрын
BOA TARDE QUASE XARÁ, DEIXA EU TE PERGUNTAR PRECISO TROCAR DAMPERS E NUNCA FIZ ISSO VC PODE ME AJUDAR ? OU SABE DE ALGUM VIDEO QUE MOSTRA ISSO ESTOU MORTO SE NÃO APRENDER A FAZER ISSO ME AJUDE !!!!!!!!!
@abrorbek2157 жыл бұрын
The very good
@EternalResonance3 жыл бұрын
i wouldn't recommend putting a cup of liquid over a highly expensive printer. less trust
@puccachedda7 жыл бұрын
i have taken all 5 screws out but still cant take head out..
@oneupkid875 жыл бұрын
I'm in the same boat situation
@andersonlpaixao9 жыл бұрын
COMO SUBSTITUIR DAMPER ? ALGUÉM SABE ME AJUDEM ESTOU LOUCO AQUI ! ALGUM VIDEO ? PLOTTER EPSON 9700