Epson ET 2800, 2700, 4800 Printhead Cleaning - NOT PRINTING Color, Black, Blank Pages [FIXED!]

[@BestPrinters]

Printer Cleaning Kit - Get Yours Now & SAVE $! [CLICK THIS LINK] 👉 geni.us/wArXsZT Epson Remanufactured 522 INK 👉 geni.us/7miiu Epson Remanufactured 502 INK 👉 geni.us/O9Y0hO Epson Ink Pad ET-2800, 4800, 2720 [Must Be Changed After Cleaning] 👉 geni.us/ezqCcy Epson Ink Pad ET-2700, 4700 [Must Be Changed After Cleaning] 👉 geni.us/Z9yi

[@hasbro35]

The clog issue happens way more often with printers than it should. Would love it if the printer companies actually added a cleaning solution tank and clean the heads for you instead of wasting a bunch of ink; but, we know that would impact re-sales. Anyway, it is much more of an issue with EcoTanks because you aren't swapping cartridges. This is very helpful and I will be printing pages more often to avoid the clogs, but use this when I forget. NOTE: My only issue with your steps is having people run a power clean at the end. Instead, I would do a nozzle check because a power clean will fill up the maintenance box with ink and eventually that would have to be replaced. Running some ink purge sheets (Pages or images that just have the 4 ink colors in stripes or a full sheet of color) through multiple times would be better to clear out any excess air and then get the ink flowing through the heads instead of wasting a bunch of ink with a power clean.

[@BestPrinters]

It is true that our cleaning uses more ink however, it is the quickest way to get back to printing normally again. As ink is able to fill the system much quicker actually when you do a nozzle check or a nozzle cleaning it's the same process just in a smaller dose so if you have to do multiple nozzle cleanings, you may end up with the same amount of ink being used. Rather than using the power cleaning twice at the most, and having instant results.

[@jackkraken3888]

Excellent point that print flush is probably something to avoid as much as possible so we don't end up soaking the maintenance box and needing to replace it sooner rather than later.! Once the maintenance box with is often little more than a little container with a sponge inside gets full you have to replace it otherwise the printer will refuse to work and even with the bypass that is sometimes available it could theoretically cause the the excess ink to spill inside the printer!

[@redlover5088]

To EASILY unlatch that "lid holder upper thingee": 1. lift your control panel up completely. 2. lower or completely remove the black plastic panel directly under the lifted control panel. 3. open the printer lid the least amount that allows you to get your fingers on that latch. 4. lower the lid and latch straight down as far as possible while continuing to hold onto the latch. 5. Push the lowest portion of the latch you are touching, straight back towards the back of the printer. This allows the small protruding "knobs" on the bottom sides of the latch, to clear the plastic housing that holds it in. (I forgot to look to see if there is a "knob" on each side at the bottom of the latch or just on the left side, but this works either way). 6. After you push the latch to the rear and it clears that housing, continue to hold it back as you lift the printer lid. The latch is spring hinged, so you must hold it back to keep it from going back into place and re-latching inside the housing. To replace, just hold the latch behind the housing, bring the lid down as far as possible and push the bottom of the latch forward toward the front of the printer. Lift up slightly on the lid.

[@BestPrinters]

Thank you!

[@bookerthomen3803]

Oh wow, I should've read this before I began. How many times do we have to do this cleaning process? Is this a yearly thing with these epson printers? I didn't know I was buying such a high maintenance printer. The liquid cleaner was also very hard to squeeze through the tube for all the colors. I even pushed too hard at one point and exploded all the liquid all over inside, so hopefully it didn't ruin anything.

[@shelbycollins546]

O pop

[@gracieramos9860]

OMG THANK YOU SO MUCH!

[@CrustyCodger]

Thanks Brother, followed the instructions, flowed 10cc 2X, reassembled, power cleaned the head and it printed like new. I have to buy the .5 litre of cleaning solution for future maintenance! 🙂

[@patriciaking6126]

Everything is cleaned. Now when you say that if the scanner cable gets disconnected, its so easy to fix it, it's not worth you putting a video out. Well guess what? Some of us need that video!

[@wdguffey]

Where do the scanner cables reconnect? Did you do a video on these cables

[@michaelruszkowski1207]

It's Very simple to insert the cables. Why you pulled your's out ? Just look. They slide right in minimum resistance inserting. If you're not successful just take a second look. Simple Ribbon Cable in use since the 60's. Good Luck! Reply to me if you wish, I've been cleaning printers for 40 plus years. Take a chance you'll be fine........ Mike R

[@B24CPN]

My cables came apart also during the cleaning process and they are in such a tight space, I’m unable to get them re-connected even using a pair of fine jewelry pliers. Ugh! ;(

[@ZsoCreative1NJ]

@@B24CPN You have to take off the side panel and use a flashlight to see the minimum resistance inserting. I was able to reinsert mine with tweezers and a little patience

[@carinathegriffin]

I tried this on my Epson ET - 2800 which wasn't printing magenta or cyan. Now it is barely printing yellow and black is right out. Went to Settings, ran the nozzle scrub program (1/9 under settings). It started to improve after 2-3 rounds. Magenta worked, if not black. Went to a 110 weight piece of paper that would press a little more against the nozzles and it is up to 75% working.

[@mariposarayna1418]

nozzle scrub program? I'm in settings, and i don't have that option on the printer.

[@MrRenoman2011]

This is the best video seen on this issue thanks so very much.

[@BestPrinters]

You're very welcome!

[@heatherkundzicz4638]

The cyan was not printing, so bought your kit and followed directions exactly, including the part where the cables came unplugged, haha! What a b**ch to get those plugged back in, but in the end, all four colors are printing now. Thank you. But the top was too easily unhinged, causing those flimsy ribbon cables to come unplugged. My advice is to not let the top be raised more than about 45 degrees.

[@BestPrinters]

Glad to hear it worked!

[@williamirelan9332]

The hinges that attach the scanner to the main body just have to move a quarter inch and they disconnect yanking the two scanner cables loose . To prevent this tape the rear corners to prevent sideways movements and the hinges won't come loose. To release the catch for the scanner apply gentle pressure to the lower section below the spring and lower the scanner until you feel the catch snap out of it's track holding it to the rear raise the scanner.

[@BestPrinters]

Thank you for posting this.

[@rogersanders7572]

Yeah, had that experience just investigating what he was showing in the video. Took me a while, but I got them both plugged back in.... wow, what a job that was.

[@BestPrinters]

Printer Cleaning Kit - Get Yours Now & SAVE $! [CLICK THIS LINK] 👉 amzn.to/4d0Gnkz Epson ET 2800 INK [SAVE $] 👉 geni.us/O9Y0hO Expedited Support Membership [Limited Time Pricing] 👉 geni.us/BPChannelMember

[@ordie2011]

You should said that at the beginning of the video. :/

[@lashaundamccullough3253]

Yeah that would’ve been nice.

[@harleycoder]

UPDATE: I let the printer dry out for a full 24 hours before putting it back together. No animals or people were harmed when I put it back together and performed the deep clean. The nozzle check after the deep clean was PERFECT! This is great because I had absolutely NO black printing, and the colors were very broken. I had cleaned until the fluids ran clear and it was a great thing. So if this un-mechanical person can get this one with the success I experienced, anyone can. Great video - I will take steps to make sure this doesn't happen again - I guess my problem is that I hardly ever print anything. Thanks so much, Printer Guy!

[@BestPrinters]

You're very welcome! I'm glad my video gave you the confidence to successfully resolve your printer issues on your own. That's my mission accomplished :) Congrats on getting it working again!

[@elkereichenberg]

thanks for the instructions, I needed to remove the wrong ink and refill my printer with sublimation ink. Could not have done it without your video help.

[@BestPrinters]

Great to hear!

[@carloscasia5276]

Hi, Do you have a video on how to fix the LCD panel. The LCD panel for my ET 2800 is just blank, its not showing anything. Thank you

[@yennguyen7624]

Thank you very much! This video help me fix the problem! Your video was very helpful!

[@BestPrinters]

Great to hear!

[@ShannonHunsinger]

Thank you so much! I followed your video and my printer now works so much better! It wasn’t printing yellow or cyan but it is now!! Thank you so much for your very informative video!!!!

[@BestPrinters]

You're welcome!

[@MrRabidtroll]

I'm thinking that placing a plastic sheet under the paper towel would keep the fluid from spreading.

[@BestPrinters]

Yes

[@mrs.anonymous6291]

Where do the scanner cables get plugged back into if they get disconnected?

[@silverwolf1270]

did you figure this out? cause same

[@user-wu6se2gs1i]

I had trouble trying to take off the top cover of the printer. I lose up the screw at the front of the printer to be able to lift the latch but be careful not to lose up too much. I move the side panel slightly to the left and I was able to unlatch .

[@danaardiel4421]

I have yellow and Cyan that are blocked fully, Is it better to try this kit first before trying a power cleaning?

[@BestPrinters]

Try the power cleaning first. Consider changing out your maintenance box especially after doing a power cleaning. geni.us/ezqCcy

[@BeckyCrabb-ek8ud]

Thank you SO very much! I usually rely on my husband to fix stuff but I was able to do this myself! Your video was so informative and easy to follow.

[@BestPrinters]

You're welcome!

[@MsTish424]

Yeah I’m gonna need a close up vid of how to open the lid of the et-2800. Please & Thank you 😂😂

[@BestPrinters]

Oh no

[@MsTish424]

⁠​⁠@@BestPrintersis that a ‘“oh no” I’m gonna have to help you bc I feel bad for you 😮?’ 😢

[@MsTish424]

@@BestPrinters Nvr mind, I got it. I went over to TikTok! 🤭

[@elizabeth4053]

@@MsTish424I don’t use TikTok. Can you upload a short on your channel please?

[@decalpals8496]

Can I access the paper feed roller on the ET-2800 when I open it as shown in this video? I've printed 16.6K impressions on this printer much of it cardstock. I know that it's not meant to print cardstock but I figure if it's meant to print envelopes, it should be able to handle the Index card weight cardstock. I just need to get to the paper feed roller to deglaze it because it's not consistently feeding cardstock anymore. Thanks for this video. A power clean of my ET-2800 fixed my problem without having to resort to opening the printer up. The video is well made and easy to follow.

[@Zawjawear]

Do I have to remove all the old ink inside the tank wells or just clean the heads

[@mariejames8370]

Thank you so much my son had a Nerf gun bullet stuck inside my printer. If it wasn't for this video it would still be stuck,. THANK YOU AGAIN.

[@BestPrinters]

Awesome!

[@RetroResinCA]

nice video! on my 2850 the top part actually opens up all the way with out having to take any plastics off

[@BestPrinters]

Great!

[@Lorna955]

Could you do a video on how to reset the replaced ink pad/maintenance box. no one tells you, once you have to replace it you have to pay for a code. you can use the trial code, but only resets it to 80%, so can't do a power clean.

[@Kurosakiphoenix]

We used the printhead cleaning solution, and it worked really well. It was printing black again, which was our issue. However, a day later it slower started to fade until it wasn't working again. We used the solution again, following the instructions listed in this video. Now, we are getting no black. Any thoughts on what could be happening here? We have done nozzle head checks, cleanings, etc. over and over again.

[@BestPrinters]

So once you see that the cleaning has worked with the kit one time for the most part, you really don't need to use it again. Well you can do now is do deep cleanings, and once you start to print normally and a regular basis, you can pull away from doing those, but you'll have to do several deep cleanings and maybe even another power cleaning in this process.

[@cosmicfear6]

Thank you for your video. I have the same problem with the same model of printer.

[@BestPrinters]

Hope this helps!

[@TheRoddrickblow]

I can't get my 2800 to do a power cleaning. I press the buttons simultaneously but it never goes to that screen.

[@Y0uRnAmEe]

I accidentally disconnected the measuring tape, after reconnecting it, the printer gave me the paper jam error. Any advice? Thanks

[@BestPrinters]

Try reconnecting it, also make sure you didnt loosen any cables.

[@berkeyfamily9828]

For the less frequent printing home, in your opinion would saturating a papertowel with cleaning solution, after printing, and then moving the printhead over the top of the papertowel to rinse away the ink, be a more effective method to keep the ink from clogging, rather than having to pump solution through from the top of color inlets when they get real bad? It seems like taking the time to do it after printing would be less tediuos and use up less solution and ink.

[@BestPrinters]

Unfortunately, that would not be a good option because overtime you could have a carriage problem by having that paper towel under the carriage. To make sure that this doesn't happen is simply printing on a weekly basis even if it's just a test print, that'll keep the ink flowing through the print and stop it from drying.

[@adamberkey8880]

I wouldn’t expect that anybody would leave the paper towel under the carriage after cleaning the printhead. But I would expect that the ink in the printhead would not be wasted when the problem is dried ink on the surface of it. By cleaning the surface of the printhead before the ink dries and clogs at the surface of the printhead I’m suggesting wasting ink with a complete flush could be avoided.

[@dawndurkee8494]

Thank you for your AMAZINGLY helpful video with so many important details! It WORKED!!!!

[@BestPrinters]

Glad it helped!

[@vJ4purzu]

Thank you! Your video is the best & easy to follow. I have another Epson in storage that I think I'll bring back in because I bet I can get it working after watching this video. Keep up the good work.

[@BestPrinters]

Thanks for the support! Glad the video helped you!

[@912582]

Brilliant, very well explained, perfect thank you!

[@BestPrinters]

Glad it was helpful!

[@user-js5sw5ly3r]

My Epson EcoTank 2800 notes a jammed error and I've tried everything there is no jam. The screen will not allow me to move beyond the error jam message to do anything with it. Can you offer any suggestions

[@BestPrinters]

These types of codes are usually not fixable unless you want to get a technician involved. In that case it might be a little expensive and not worth it at the end of the day. It may be time to buy a new printer.

[@vickieroskom5175]

My brand new one is doing that.

[@amys6168]

Thank you for the video, but unfortunately my printer still won’t print black. What should I do next. Thank you for advice

[@BestPrinters]

Do another cleaning at this time warm-up the solution

[@B24CPN]

I used your video here to know how to clean and unclog my epson et-4800. I cleaned out tubes, dampers, and print nozzles. I was able to get all colors working again *except* for the black. Anyone have any idea what to do further? Essentially if I can’t get all 4 colors working it’s useless for my sublimation projects. Thank you again for helping me try!

[@BestPrinters]

do another cleaning on the black nozzle, try warming up the solution

[@LoveThatPhantom]

What would you recommend I do if I still have a color that won't print after doing all these steps? I had two colors that wouldn't print correctly. Black wouldn't print at all. And yellow was spotty. Now after following your steps completely. Black is printing fine. But now yellow won't print at all. Should I go through the process again? I even went a step further and used the syringe I had to drain the ink from the tube. Before cleaning. And then replaced it back before I started printing again.

[@Steven_Rowe]

I have an et2710. It prints magenta, I test print revealed no yellow printing, head clean didn't fix it so have bought a cleaning kit. One question. The headcis parked on the right hand side of the printer and appears to be locked in position, how do you get the head to the mid position?

[@BestPrinters]

Print a print quality test and unplug the printer while it is printing.

[@MTaropatchkeikis]

Is the fix just for this printer or all epson eco tank printers? I need help with my epson eco tank 16600 not printing black solidly.

[@BestPrinters]

Hi there, the Epson EcoTank 16,600 will have the same process of repair as the Epson 15,000 here is that video kzbin.info/www/bejne/hp_RmYybiL6Fnbcsi=k_tXbDjFhcvuQERO

[@MaryAnnSmith-eg9up]

My printer is only printing black ink. Got the top off and was ready to follow your steps to clean the print head and when I took the cartridges out I noticed that they were all empty- except the black. My tanks are currently about 80% full. Could my issue be the clog is in the lines? Will this print head cleaning work?

[@BestPrinters]

With your specific scenario, it seems like the lines may be clogged. That is the lines that go to the printhead so in this case, what you want to do is run a power cleaning, and that should push the ink through those lines into the printhead. so this cleaning may and may not help try doing the power cleaning first and if it solves the problem and you noticed that there's ink back in those cartridges then you're good if the problem persist you may wanna continue on with this cleaning.

[@CarlaBattermann]

I was fine on all colors except yellow. NO yellow at all. So, I did the your cleaning, got my printer put back together, waited the 24+ hours, did the power clean, and ran the nozzle check... I get a whole sheet of SOLID BLACK with a few blocks of color on the sides... I try to just print a document... SOLID BLACK PAGE!!! HELP PLEASE.

[@paraphoenix1898]

This was a really good video! It helped me out a lot! Idk if you still look at comments but I think I made a mistake and didn't unlock the print head before opening everything up. I ended up just pushing the block out of the way, but now I can't get it back in place. Will this damage the printer if I turn it back on without locking it place? Is there a way to get it back in?

[@BestPrinters]

All you can do is attempt to power on and see if it goes back in place there's really no other way.

[@paraphoenix1898]

@@BestPrinters it seems to have gone back in place and is functioning normally! Thank you!

[@jcscarpino8344]

My test prints are good, the purge print is perfect. But when I print a picture I get white lines . I'm at a loss...can you help

[@djsymons61]

So my ET 2800 keeps reading paper jam, in rear of printer. There are no paper jams at all. When I first turn the printer on a piece of paper loads and comes out the front with no problem. When I request a print it says there is a jam

[@BestPrinters]

It may be time for a new printer, there is no diy fix for that code.

[@djsymons61]

Great!!! It’s two weeks old!!!

[@elguerrero9140]

As soon as I started the “power cleaning” a minute after it hit me with “ink pad service” error 😩 it won’t let me print now😫

[@BestPrinters]

Oh boy

[@jmeza157]

Hi! I have the 2850 that keeps leaving black ink behind causing smudges, any idea how to get rid of this?

[@BestPrinters]

This cleaning may help, also cleaning the ink waste pad will help.

[@elizabeth4053]

@@BestPrinterswhere’s the ink pad thingy and how do I find it and clean it. Pretty please 🙏🏻 🍒🍰🧁

[@derekcheung1388]

Any other tips? I flushed the Cyan 3x already using 2 different solution. Still white lines for Cyan...

[@BestPrinters]

Aside from the cleaning kit, you will also need to use the power cleaning function on your printer. That is what is going to bring back the ink into your printhead.

[@kaimyahall7015]

My printer has been down for a week, I could really use your help . Please and Thank you. How do you reset waste ink counter?

[@BestPrinters]

turn off the printer for 24 hours and then power back on

[@pattyhadley7185]

How do you fill the syring???? Nothing fits on the thing

[@BestPrinters]

You should be able to fill the syringe before putting on any attachments.

[@sherithayates8779]

I cannot get ink to go into the printer. Is there a good way to clean or unclog the area where I actually fill the ink?

[@BestPrinters]

The power cleaning function should help you get ink back into the system

[@eciripsujiro6191]

Hey great video! I actually got a printer cleaning solution for my EPSON L3110. Got a question. Do I really need to heat up this solution to use it? Can I not just use it as is? And for heating, will microwaving to warm up for like 10 seconds or so work or will microwaving might affect the molecules of the solution?

[@BestPrinters]

Hi, if you feel that the unarmed solution is not breaking the blockage, you may need to warm it up. I highly advise you do not microwave the solution instead warm up a pan with hot water and slowly warm up the solution that way warming fluid up in the microwave is not safe.

[@mikegreen7992]

is the power clean required after doing the printhead cleaning with the solution?

[@CycloneCowboy]

Great video, covers the cleaning perfectly, but it's a semi-fail because there are no instructions for re-attaching the two, small ribbon cables that come off on a lot of first time cleaning projects. It's easy to see where these go if you look at the backside. They do require very careful reattachment, using a very steady hand, good illumination and needle nose pliers or forceps, being very careful not to pinch the cable and damage it. I strongly suggest taping the top cover of the printer to the body so it does not fall off. The blue-tipped ribbon cable only goes in a few mm, not all the way, so don't damage it by trying to push in too far. Blue side up. The bottom line, DO NOT LET THE BACK OF THE COVER COME OFF!

[@BestPrinters]

Thanks for sharing

[@CariCorene]

Is there advice on how to reconnect the fragile white scanner cords after they have detached? My printer is now unable to function, because the scanner (which I don't use at all) is now disconnected.

[@h.m.2434]

This printer has a head cleaning option feature (under the maintenance menu) that takes about 3 minutes to run. Does that really do anything?

[@BestPrinters]

Sometimes yes, sometimes no

[@ritawilson7017]

Hi ok I did the printhead cleaning solution and was trying to put more ink in my printer but the ink is not going into the part where the ink goes, what can I do to fix that. And do you have a video on that. Thank for your help

[@BestPrinters]

Hi Rita, I most likely do have a video of how to install the ink on the Epson Eco tank 2800. If you click on my channel icon and go to my channel page, then click on videos there should be a search bar where you're able to search up videos. It may be that you just need to do a upward and downward motion while installing the ink bottle and that would free up the ink so that it's able to flow into the ink tanks. If you require any additional help, please create a new comment so that I am notified.

[@markruggiero3321]

Hey Printer Guy, let me tell you about my ET-2803. It paper jammed, and I got it all out the front, nothing from the back. I say I got it all, and with the help of the comment below, I got the lid up and can see no remaining paper anywhere. When I tell it that it's cleared and push the diamond button "complete", the print head slams to the left, slams to the right, and comes back to rest left of center. I mean SLAMS. Then it says it's still jammed. I don't know how it determines it has a jam in the first place, or if there's a sensor somewhere that's still got a small shred in front of it. I can plainly see the mechanism it uses to determine if it's out of paper, but I'm not able to see a cause for my issue. Can you offer me any insight? Thank you.

[@BestPrinters]

Paper jams can be complicated. It would be worth consulting a local technician. They may be able to help you out.

[@arlenehuerta6231]

How do you empty ink and refill the ink do you have another video to show this process?

[@BestPrinters]

There is no need to empty the old in the only place that the old thing needs to be flushed from is the printhead. Which is why we're doing the cleaning. Simply add new ink and it will mix with the pre-existing ink and when you go to do a power cleaning, that mixture of ink is going to be pushed back into the system, and you should be printing normally again.

[@arlenehuerta6231]

Great thank you so much for responding!!! And that makes total sense cause that’s what I was thinking but I didn’t want to assume or break my printer because Epson doesn’t make it easy at all for you to empty the reservoir. And then you break it and boom gotta go buy a new one. Your video is great I just hope it all works for me! Printers are not my best friend!

[@bobr511]

On my 2750, Black and Magenta work. When I pulled out all 4 of the cartridges as you showed, it looks like Yellow and Cyan do not have ink in the cart. Is this typical or is there another issue that needs to be addressed?

[@holliwudsmith8425]

U have to connect hose and pull

[@B24CPN]

What is the purpose of waiting the 12 hours after doing the power cleaning procedure, and what does this actually accomplish?

[@BestPrinters]

I would say to actually wait 24 hours. The purpose and waiting this period of time is to ensure that any cleaner that may have gotten on or around the electrical components within the printhead have totally dried before you power back on you back on prematurely, you can cause a short circuit and fry the printer.

[@MariellaDelgado]

Thank you, I fixed my printer!! :D

[@BestPrinters]

Glad it helped!

[@PS-on7jm]

I have Ecotank 2710 and it had some problems with printing colours. I bought the kit on Amazon and I did the procedure. The printer does not print any colours at all anymore, except for black. Any advice?

[@BestPrinters]

that is normal. You will need to run a power cleaning after using the cleaning kit.

[@amandahugginkiss61]

Can I hit it with some compressed air to speed up that dry time?

[@BestPrinters]

That might spread the fluid to other components, just be careful.

[@amandahugginkiss61]

@@BestPrinters lol I waited it out and got it back online with no ill effects. Thanks for your video and subsequent advice! You make me look computer savvy with my kids but I’m just trying to save a buck. Couldn’t pay for that admiration so, thanks. Also couldn’t pay a tech to fix my printer so thanks for that too. You the real MVP!

[@catrenabritton109]

You said use warm water if the solution won't go through. What causes the solution not to go through at room temperature?

[@BestPrinters]

A dried ink clog will need warmed up solution to break the clog.

[@heatherkundzicz4638]

Warm cleaning solution, not water

[@roxydilbert4289]

What about if my printer was full of ink? Can i still do the cleaning?

[@BestPrinters]

Yes

[@merrybobosky4842]

so how do we reconnect the scanner cables back up mine came out and have no idea were they connect back

[@BestPrinters]

Google scanner cable port, image. for the ET 2800

[@merrybobosky4842]

yes sir i found them they were right under were cables came out thank you . @@BestPrinters

[@hotcheetobabe8722]

why do i need to be a rocket scientist to use my printer

[@BestPrinters]

I know right 😬

[@skfire6821]

AWESOME!!!!!! Thank You for the info.

[@BestPrinters]

You bet!

[@junkman007]

This is an amazing video! Thank you for the detailed instructions :)

[@BestPrinters]

Glad it was helpful!

[@dandee28]

is this the best way to flush out all the old ink as well and put different ink inside?

[@BestPrinters]

This is a partial flush, a total flush would have to start from the ink tanks.

[@HannahZachariah15]

Does this also apply if I want to clean out all old ink so I can replace it with sublimation ink?

[@monicagarcia-pg2ex]

Hi, last time I tried to do that. I broke my other printer so I have to get a new one, but it’s still giving me the same issue for some reason the cayman blue is the only one that gets messed up even in my other one is any other way that you can clean up without going through all this I bought my printer two months ago and it’s already gave me the same issue as my old one, and the other one only had it for five months

[@aagg3311]

Hello. I just did that to my Epson ET 2800 on Saturday. I just turned it on and is saying "scanner error" and is not letting me do the power cleaning. I promise you I put everything back very carefully. What can I do. Please help me. Thank you

[@BestPrinters]

Reset the printer

[@aagg3311]

Thank you for replying

[@SamShlivko]

Could you please link me to a tutorial on how to get my ET-M3170 to print. I can't seem to find anything on-point online. It is currently printing blank pages.

[@christinaphillips1739]

I tried all of this and now I have an E-02 error. I see a very thin white ribbon toward left rear area that appears to have pulled loose but I cannot see where it came out of. Anyone know? I cant proceed. The error wont let me even after powering down and unplugging.

[@dianagarcia8053]

I need help. My printer is drowning in ink when i put paper at the bottom

[@BestPrinters]

Can you describe the problem more detail? Does it happen when you print also please respond in another comment so I can get notified.

[@derekruddock6996]

Is there a trick to actually seeing the ink levels in the fron 4 windows. Ive never been able to see ink levels thru them??

[@BestPrinters]

I've heard of this issue issue. I'm really not sure of a solution.

[@studivan]

The problem with inkjet printers has never really been the ink, it’s always been the print heads, they never really get clean and a print head cost almost as much as the printer if you get it from Epson.

[@robinheater9554]

I still have lines. I have heard back. From you. Can you please tell me what else to do

[@BestPrinters]

Repeat the cleaning.

[@robinheater9554]

I have the Epson 2800. But we used the hippo ink. Do I need to stay with the same brand or would it hurt to go back to the ink that’s made for Epson printer.

[@BestPrinters]

I would stay with the same brand.

[@feliciarogers5250]

Please HELP!!! I can't fill the tank on the black. Will doing this clean fix that or do i have a completely different problem?

[@BestPrinters]

That is an entirely different problem.

[@feliciarogers5250]

@@BestPrinters do you know how to fix it?

[@spongebobuniverse]

There is another video with an Asian man fixing the problem you have. Search epson 2800 not printing.

[@tonyacena]

What if the one doesn't let the solution through? How do you unclog it then?

[@BestPrinters]

Then you need to warm up the cleaning fluid

[@annjerome8556]

Thanks for the video! However I must have pulled up to hard because the top came off completely. and the smaller white ribbon came unattached, so I have no clue where to reattach it. I get a -02 error scan code. If possible a close up shot of the ribbons would help me to put it back thank you.

[@annjerome8556]

I found a video that showed where to plug the ribbons back in. Thank goodness it is working great again.

[@TranquilLois]

@@annjerome8556 WHERE?!? I have been looking for HOURS! Please help me out!!

[@BestPrinters]

Great I'm glad that you found a solution. This comment will help others that may have the same problem. If you can share the video in an additional comment @TranquilLois is asking for it.

[@Bimtasprints]

Pls i need assistant on my new epson l3210 printer it prints a blank page

[@BestPrinters]

You need to do a printhead cleaning!

[@hing983]

hi my espon 2880 ecotank all the cartridge is empty tank how to prime the ink

[@BestPrinters]

The power cleaning will prime the ink, make sure all colors are full.

[@NicolesFactory]

I tried this and the black piece came off. How do I insert that back in?

[@BestPrinters]

Which black piece?

[@ised8m]

Thank you this fixed the problem!

[@BestPrinters]

YES!

[@vickieroskom5175]

Can u help me with new 2800 keeps saying paper jam or wrong paper.

[@BestPrinters]

The paper jam. I'm not not sure how to help you but for the wrong paper, you can go into the settings of the printer and make sure that the right type of paper is selected.

[@okccopswife]

I have performed this a few times now, but Cyan is still not printing at all. I did the power clean & still nothing. I’m afraid the block is in the tubes or up higher than the nozzles. Is there anything else I can try? My husband wants me to trash it. Ugh

[@BestPrinters]

Try doing the cleaning again but this time warm up the cleaning fluid. Don’t give up, be ruthless!

[@jazminandablo4822]

I try pushing the syringe but nothing happens is it that clogged?

[@juliaagresta9769]

I can’t even get past the first step. The black thing that I need to lift out/detach from my printer won’t budge and I’m afraid I’ll break it. I can’t see a thing in there to help me

[@BestPrinters]

You may want to get help from someone.

[@Julia-zz3gl]

The link doesn't seem to show that cleaning kit.

[@BestPrinters]

The first link?

[@shannonmcdaniel5198]

Hi, I did all of this and still having issues with lines in the black printing. I am not sure what I can do now. Any suggestions???

[@BestPrinters]

Try warming up the fluid and also make sure that you're black ink is totally 100% full.

[@jessicaeoffkms7788]

My Epson ET 2803 keeps stopping at about 30% and giving a W01 paper jam error. After a few times, it will say foreign material error. There is not foreign material. I have cleaned the rollers and updated drivers. Have you had any issues with this or other suggestions for fixing.? Epson won't help because warranty ran out a week before issue started.Teacher in desperate need of a working printer.

[@erinsuzy613]

Same thing just happened to me and my warranty is up next month. I'm so disappointed. I thought I was upgrading but my cannon printer was a workhorse and I should have kept it.

[@RJaime869]

Those cables disconnected on me towards the end. Where do they connect to? I can’t find that

[@heatherkundzicz4638]

Get an assistant to hold the top hinged-and-ready to close at about a 45 degree angle. Then get a bright little flashlight to look in from the back corner under the top, and find the connecters for the cables on the board, and wiggle them back in. It was not easy, but it can be done. If you have "fat fingers", you may want to enlist someone with smaller hands.

[@wendyward-wf3gc]

What if it spilled ink onto bottom tray under the print head.that white strip looks multi colored. Will it still be ok?

[@BestPrinters]

After it dries it will be ok.

[@briannabyrd-m1t]

followed all steps, now saying error and turn off. HELP please!

[@mtuipala1]

I did this and nothing is printing now… what else can I check on?

[@BestPrinters]

Make sure to run the power cleaning.

[@Angieram45]

my printer will not print nothing can not make the head where the ink is in help please i can not unlock it