Eride Pro SS jackshaft, pulley, belt change

Рет қаралды 756

Күн бұрын

Пікірлер: 29

@MsHodgey 27 күн бұрын

Finally a guy that gives clear instructions, and films every detail up close with perfect lighting to boot. Hats off to you sir. Well done.

@tumbles94 24 күн бұрын

Thanks! I was not going to film it but thought I would because I could not find a super detailed video out there on this.

@MsHodgey 24 күн бұрын

@@tumbles94there definitely is a need for installation videos for the e ride. Hope you film all your modifications like this. Super helpful.

@AnimalEv 3 ай бұрын

I really like how clear and concise you are with each step! By far, the best DIY video for the jackshaft to date. Well done Sir

@tumbles94 3 ай бұрын

Thanks! I figured I was going into too much detail. There was more I edited out for time sake.

@paulewing28 Ай бұрын

Very nicely done appreciate the step by step made it look easy

@tumbles94 Ай бұрын

Thanks! Yeah had to learn as I went.

@AdrianCasillas-qs1lf 2 ай бұрын

Thank you so much for this video!! I was a bit skeptical about doing this myself but now i can do it knowing what goes where!! Again tnx!

@tumbles94 2 ай бұрын

Glad I could help! Yeah, it is not too bad once you start doing it.

@sethdaniel9194 24 күн бұрын

Great video thank you for making this!!

@tumbles94 24 күн бұрын

Glad it was helpful!

@EmotoModsAndMore 3 ай бұрын

I’m not sure if you have seen my “ Eride Pro SS How To: Remove Belt Pulley “ Video I made but I have that same exact aftermarket belt pulley I got mine from MXpartshop I actually bought that pulley before I even bought my bike because I knew when I got my bike it would arrive with that shtty Version 1 belt pulley and I didn’t want to ride that stick one at all and I didn’t want to waste my time with the version 2 warranty belt pulley..at the time it was before warp9 came out with their jackshaft so I’m still running the stock jackshaft but I’m definitely upgrading to this warp9 jackshaft soon as I can spend more money on my bike😅…also in my other video “ cable management part 2 “ I used that same black plastic hose for my rear break cables like your bike haha 🤙🙌 great video I think yours is better than mine…🤷‍♂️

@tumbles94 3 ай бұрын

Oh yeah I watched to see how hard it was and it was helpful! You let me know what pulley you used and I got the same one. My bike had the one that needed to be replaced as well and thought this new pulley looked better. The Warp9 Jackshaft is nice and came with everything including new seals for the bearings on both ends. I use that plastic line coverings everywhere I can just to add some extra protection. I pretty much ride in the woods 100% and no street use really.

@Theonlyjezus_ Ай бұрын

How do you know if you got version 1 pulley or 2 on eride pro ss

@tumbles94 Ай бұрын

Go to this spot in the video and if it has welds like my old one then it should be changed. kzbin.info/www/bejne/qZaqlYCtaseAadE If it does not look like that and your bike is newer you may have the new one. It looks thicker on the side and has like little screw looking things if I recall. If you bike is under warranty you can get the new one sent to you for free.

@EmotoModsAndMore 3 ай бұрын

I like that number plate on the side of your bike how it’s zip tied on..looks kinda of ugly but I like that, people say my bike is ugly all the time because I have custom plastic side panels zip tied to the sides of my bike 😅

@tumbles94 3 ай бұрын

Yeah I had to make that on the fly for a woods race I did using some old signs they had laying around. I like how it look all homemade and stuff so I have left it on and it has held up. Yeah I am not worried what others think..lol

@barnescore2797 4 күн бұрын

great video with clear instructions i’m new to the e bike community what exactly is the benefit of getting a new jackshaft and pully?

@tumbles94 3 күн бұрын

I am new as well to e-bikes. There were some pulleys from eride on new bikes that would come apart while you were riding so they would warranty them out. I just replaced mine because I had one that was defective. While I was there I went ahead and put in a stronger jackshaft because I may upgrade the motor and battery later and this one can take more abuse I am told. You are also able to grease the bearings on it easier as well.

@mischifischi 3 ай бұрын

Thank you for showing this! Whats the width of the belt? Thank you in advance and keep it up 👍🏼

@tumbles94 3 ай бұрын

Thanks! I think it is 20mm width from the specs. It is the same at the stock Dayco belt. Gates 560-8MGT is the part number.

@mischifischi 3 ай бұрын

@@tumbles94 Thanks for the info!

@tumbles94 3 ай бұрын

I measured the old Dayco belt, which was 20mm if that helps you.

@mischifischi 3 ай бұрын

@@tumbles94 thank you very much for the effort!

@boomhowre 3 ай бұрын

Did ya clean your chain? ;)

@tumbles94 3 ай бұрын

Sorta then just added more chain lube on it.

@RedBeardMoto 2 ай бұрын

What size spindle nut socket is it?

@tumbles94 2 ай бұрын

Not sure. I got it from rev rides and it may be for a suron and I semi hammered it on. Once I bent the little tabs it fit fine. I can't find any part numbers for it from my recept.

@tumbles94 2 ай бұрын

Some people use a flat blade screw driver and a hammer to spin it.