EUC Bent rim repair RS-T Begode Gotway

[@windowmaker]

Nice. Just stumbled on this, will be useful later.

[@mataa_chrama]

Just happend to me on my msx, gotta try this, thx 😅

[@LS-jk3fk]

have a noticeable bend in monster pro rim and i think it was from when my tire pressure got really low at one point because of a huge bump, heard and felt the rim hit it ( i unknowingly rode it on 12 psi for awhile, I have it usually at 36 - 42 of course since I am a big guy) it is also causing the tire to look like it wobbles very slightly, but the ride doesn't feel off. hope it's safe to continue or should i just hammer the rim into place

[@roghaj]

Look up what a dead blow hammer is. If it feels ok, I'd leave it. I'll be racing a wheel tomorrow with a bent rim. I got the tire fairly straight.

[@360vroomers]

I have an RS with similar size dent. I have hit it with a heavier hammer but it seems to not straighten…?

[@roghaj]

You can have a little more control over the situation by using a car jack and finding a space that fits the car, jack and the rim and then begin putting pressure on the rim. There is a spot with two cement posts in the ground near each other. That works for me. But now I just use my hydraulic press.

[@goofynate9]

Good video as always Mann

[@roghaj]

Thank you again. What wheel did you end up getting to replace that Nicola?

[@goofynate9]

@@roghaj I have a Master sitting here still that is bricked. I replaced the upper frame, the wheel was still slightly crooked, even after the new frame. I was told by alienrides a calibration should straighten it out. I attempted and it died. Won’t turn on at all now. Nothing else looked broken. I inspected the battery packs. I’m pretty sure the controller fried. I have done a lot of work on my Tesla keeping it alive. 🤣

[@rayrokni]

nice job roger

[@joshuajones6113]

You mentioned that the Sherman Max tire had a tendency to fracture when doing this repair. Would gently heating it possibly help?

[@roghaj]

Heat does help. Most of us are lazy and like to do this with the tire still on. Makes heating sufficiently a no go. I recently found out that the EX30 rims fracture as well.

[@joshuajones6113]

@@roghaj thanks. I'm not overjoyed to tear the wheel apart either, but I figure a fracture is probably more annoying to deal with.

[@sbrianrowe]

@@roghaj😬 just bent my ex30 rim ouch

[@BlueSamurai88]

What kind of screw set is that. Are they special drill bits or something. My Phillips doesn't even match.

[@roghaj]

PH1 maybe. I don't remember. I miss that wheel.... sold it a while back.

[@Afritunez]

what type of wood is this ? and what are the dimensions ? thanks

[@andyhan5008]

Nice vid Roger. I got a master now too so let’s see who leads who on our next ride lol. Also what are ur thoughts on the master pro?

[@roghaj]

I might get one. So you think the Master is faster than a Monster pro? If you were behind me before, you'll be behind me again 😆

[@andyhan5008]

@@roghaj i been cursing at 52-54 just riding the beeps like a mad man. When I get my master pro it’ll be game over brotha 😝

[@roghaj]

@@andyhan5008 I can only hang in the 50’s for a minute or two before the voltage sag starts taking me down. We can get things figured out at Apple Valley speedway in November. Deal?

[@andyhan5008]

@@roghaj yessir apple valley it is bro. Hope u’re doing well n ride safe brotha

[@frankhernandez133]

With the rim being bent, I found that it is common for it be bent around the same area on the other side of the rim. Any suggestions about fixing the rim on either side while both areas are bent? How does this method effect the other side of the rim?

[@roghaj]

Oops missed this. The wood on the other side will address the bend a bit. If its bad enough, flip it over and to it again.

[@Blox117]

​@@roghaj if that wood block crumpled your fingers would be mashed. use a metal instead

[@CogitoErgoSum67]

Was the wheel out of true wobbling before and got better after? I have the same problem, mine is a smaller bent but the wheel wobbles so much, am hoping when I do what u did it gets better...

[@roghaj]

Felt like I was hitting a tiny bump every revolution. Wasn't a huge deal but now its perfect. Your issue might go away if you empty your tire of air and squeeze the tire off the rim and reinflate it. Good luck.

[@CogitoErgoSum67]

@@roghaj my tube blew up on impact and the rim bent a little less than yours, but the wheel wobbles from side to side, hopefully it works, gonna try later

[@Afritunez]

@@CogitoErgoSum67 how did go? Dame problem here

[@syamsulum]

Wow... Thanks

[@hertzdount]

Not sure where you are doing your repair - but aren’t you worried about damaging your floors?

[@roghaj]

1.24” thick granite

[@A-Viking]

Informative thanks

[@sek3ymisek3ymi]

Hey 👋 Can anyone tell me , i have a small bend in a v11 rim . The ride still feels basically perfect and no wobbles or bump . Can I continue to ride or is it dangerous and I need to fix it asap ?

[@roghaj]

Not a problem to keep on using it. I recommend not attempting repair unless it is causing issues.

[@sek3ymisek3ymi]

@@roghaj thanks for the reply and video!!!