I have seen a lot of how to videos for smoker builds and yours is by far the best one out there. You provide a lot of information that is needed that others do not include. Thank you.
@SmokerBuilder3 жыл бұрын
Thank you buddy! We try to put the best info to help newcomers all the way to experienced pitmasters.
@torreyball4447 Жыл бұрын
Information is a great thing when your making videos! Thanks
@markwarnke76804 жыл бұрын
Here's a tip I've found helpful for making the vertical lines around the tank. Use a roll of magnetic sheet vinyl. 3" x10' for $12-$15 on amazon. Great Videos by the way!
@SmokerBuilder4 жыл бұрын
Awesome tip bro! Thanks for sharing!
@465ryda3 жыл бұрын
It's nice to see another fabricator show off skill sets. It's pretty uncommon for older guys to show the shit they've learned over the years.
@hddm33 жыл бұрын
That is amazing. Watched it over and over. Very professional guys! And thanks
@tomstepp69452 жыл бұрын
Excellent video!
@thomasgillott78333 жыл бұрын
Do you have a complete bung removal and patch video?
@gmongard Жыл бұрын
Thank you Frank!!
@jray76563 жыл бұрын
If ya have the money flange wizard has a large bore pipe center finder. There super handy.
@timothyleger43854 жыл бұрын
Great information Frank !!👍👍✌✌🇺🇸🇺🇸😁
@SmokerBuilder4 жыл бұрын
Thanks buddy!
@timothyleger43854 жыл бұрын
@@SmokerBuilder 😁😁👍👍✌🇺🇸🇺🇸🇺🇸🇺🇸🇺🇸
@johnshull1023 жыл бұрын
Do you have a video on how to layout the holes that are cut in the round ends where the firebox is welded to the cook chamber ?
@Romas652 жыл бұрын
Man, I've been asking this question from all smoke builders, never get a response. Wish I could,,, been stalling on building my smoker due to not being able to figure this out.
@clinthart65414 жыл бұрын
That good info looking for a tank right know to build a smoker I see I need to by a new square like you have good tool. Thanks great video's
@jrcll78563 жыл бұрын
awesome video.... very well explained
@sklise14 жыл бұрын
love ur videos. I am going to try and make a vertical from a 100g propane tank. Not sure I will do an offset or just smoke from the bottom with an indirect plate.
@buckeyemtnman46713 жыл бұрын
whats the brand/make of that tape measure??
@johnallen13082 жыл бұрын
Can you cut at the 12 and 3 oclock marks or so you have to come in a couple inches on each mark then cut
@SmokerBuilder2 жыл бұрын
Hey buddy, yes you can cut at 12 o’clock and 3 o’clock. The only catch is at the door might be a little heavier at the 12 o’clock position
@johnallen13082 жыл бұрын
Ok thank you
@arthurwagar62243 жыл бұрын
I didn't know 3 4 5 works on a curve. Interesting. Thanks.
@jasonc97654 жыл бұрын
Where the heck did you come across the flexible tape measure? That’s pretty slick.
@hectormarines9231 Жыл бұрын
I second that.
@monte.est89254 жыл бұрын
This was a great tutorial
@SmokerBuilder4 жыл бұрын
Thanks buddy!
@airplanetrucker23162 жыл бұрын
Good videos!!!!! 💯
@edgarnava20253 жыл бұрын
I’m in the process of building a 250gal smoker. I have some questions. Are the cut out for the doors 1/4 of the circumference or slightly less? Does the cooking grate sit exactly halfway or slightly lower?
@joshwinters62493 жыл бұрын
any particular reason you remove the bungs rather than just plug them and flip it over?
@billyramsey86493 жыл бұрын
Where can I find the tape measure
@richardwyatt68983 жыл бұрын
Would you please tell me what kinda marker you were using?
@SmokerBuilder3 жыл бұрын
We bounce between soap stone (chalk) for the white or for the black marks. We use the Milwaukee marker red body with a black cap.
@richardwyatt68983 жыл бұрын
@@SmokerBuilder thank you very much I appreciate it
@SmokerBuilder3 жыл бұрын
Not a problem at all!
@caseycockburn16253 жыл бұрын
How much would you say a typical 250gal reverse flow smoker weighs?
@SmokerBuilder3 жыл бұрын
So many things vary, but normal would be around 1000 to 2000 lbs. every one is different depending on customer options.
@alfredomanzur99313 жыл бұрын
I need one smoker.
@garydutra88143 жыл бұрын
Do u sell smokers u build? What's your company name?
@SmokerBuilder3 жыл бұрын
Our company name is Smoker Builder. Yes, we build smokers from UDS all the way to 1,000 smokers with everything in-between as well!
@henrimoffett36833 жыл бұрын
That 10 thing is genius actually lol
@chadmjohn3 жыл бұрын
LOL, the tape measure starting at 10", I had to laugh. Not that you did it, just at the comments. I do similar, all my tapes have incremental inch marks after each 12 inches, so the first inch after 12 has 2 markings, 13 and 1, if i need 6 inches I start at 12 and read the 6 on the tape.