Your video is so cool! I am one of your fans in Korea. I always cheer for you. Stay healthy!
@CallofDoobie5853 жыл бұрын
Peace from the u.s.a
@dilliongargon69743 жыл бұрын
Love the rotisserie idea, cool
@davidprice493 жыл бұрын
watched you installing front hub w/bearings. they need to be torqued to 5-7 ft pounds. especially important if using synthetic grease. doing the old way just by feel,you can wind up with 25-30 ft pounds on the bearings(synthetic) which can cause bearing failure. did it once.
@pauldionne16653 жыл бұрын
I will remember that if I should ever do that (bearing replacement). Thanks for the tip.
@marcosmota10943 жыл бұрын
A car show that adds time to your life? Subbed.
@tolomirog3 жыл бұрын
Bravo super video je vous regarde depuis la France
@malamri4243 жыл бұрын
those baer calipers are sweet
@pauldionne16653 жыл бұрын
Yea that kit is some real eye candy for sure.
@bmstylee3 жыл бұрын
They are cool. The 6 piston kits are even cooler.
@Rangernpscience3 жыл бұрын
It's great that you have the skills and money to weld up axle ends
@pauldionne16653 жыл бұрын
That alignment tool was REALLY cool , sure helped him weld it together and straight .
@gernblanston49563 жыл бұрын
Welded it up, yes, skills, not so much
@teaguegearhart98513 жыл бұрын
kzbin.info/www/bejne/g5fLoGNjhqasi7c
@2511jeremy3 жыл бұрын
@@pauldionne1665 have a similar setup at work tho our alignment bar is not hollow
@caneighbors78753 жыл бұрын
Designed and made my own pieces years ago, from drop and scrap material when I found them, and lathe time (not a machinist). Bought a welder, did work; bought a bigger welder, did more work; bought a TIG machine, and continue to work. Learn something new every time I build something. Not a lot of money involved, just patience, effort, experience, and building upon that. We all start from square one, unless we make excuses for not starting (
@johnathansmith90593 жыл бұрын
Hope all is Good!
@1320Jason3 жыл бұрын
Nice!
@bigmikex23333 жыл бұрын
Huge Miller fan boy here.....why would Miller continue to build the Millermatic 190? 230 only, good up to 1/4". For another 300.00 you can get a Millermatic 211. 110 or 230 and good for up to 3/8"
@zippythechicken3 жыл бұрын
you're brave doing that
@drivexyz22973 жыл бұрын
that guy knows welding
@gernblanston49563 жыл бұрын
Lmao, that was a shit job. I would never trust that axle housing
@2511jeremy3 жыл бұрын
@@gernblanston4956 as a guy who makes housings for a living it was ok ish we tig weld everything including the housing and i have never seen welds that big that housing must of had huge gaps from the tubes. And our tubes are turned on a lathe never hand cut and grinded
@pauldionne16653 жыл бұрын
@@2511jeremy thanks for the tip Jeremy. I thought it was ok'ish as well.
@2511jeremy3 жыл бұрын
@@pauldionne1665 i meen it will do what they want with out falling apart but that housing was probably made for a 3 1/4 or 3 1/2" tubes and that company just filled it with weld looks awful
@RyanTheMalamute3 жыл бұрын
There's always the KZbin expert in the comments... just shut up. Currie has been around a lot longer than just this axle. I'm sure they know what they're doing, considering they're a national company.
@THROTTLEPOWER3 жыл бұрын
Nice vid!!!!!!!!!!!!!!!!!!!!
@dipe2773 жыл бұрын
Isn't the currie rear end a little overkill for a V6 not making 400hp?
@usMarinecuv9023 жыл бұрын
You could use the shims as feeler gauges.
@AndyFromm3 жыл бұрын
Nice 👍
@the_car_guy59153 жыл бұрын
I would like to put an Ecoboost in my '54 one day.
@paulvaso85243 жыл бұрын
Hey guys, what happened to the flat head?
@jamesdiehl86903 жыл бұрын
Stretch on the bolt when torqued? Like mains and rods studs?
@impavitus3 жыл бұрын
What I thought
@jamesdiehl86903 жыл бұрын
@@impavitus I've been watching several KZbin series; powernation, etc.. and they use a torque wrench with a specific Guage that measured bolt stretch when tightening studs on heads and main caps. The engines were LS and Coyote engines for street/strip use.
@zippythechicken3 жыл бұрын
more likely something on the threads
@impavitus3 жыл бұрын
@@jamesdiehl8690 there's definitely a science to what they do
@ronniejohnson3173 жыл бұрын
When you get bored, call Kasse to stress test that rear end.
@RaulNatera3 жыл бұрын
Great job!!, very good!!, where you find the power pack for the ecoboost?
@larryw54293 жыл бұрын
Needs more room between bed and tire.. Get a flat and you will have big problems!
@digranni1283 жыл бұрын
Eu não entendo esse KZbin, se o canal é gringo, pq o comercial é do Brasil?
@413x3983 жыл бұрын
That whole rear housing is overkill for that engine.
@bmstylee3 жыл бұрын
If you overbuild it you can drive and not worry about it breaking. Plus with tuning and bigger turbos that v6 can make some healthy power.
@413x3983 жыл бұрын
@@bmstylee The weak point here would be the standard gear housing and a clutch-type limited slip. If you really worried about a regular housing deflecting just weld on a common back brace. This is, of course, just a commercial for Currie's product and the bragging rights associated.
@allentrotter13273 жыл бұрын
Good thing it’s their build and not yours then.
@413x3983 жыл бұрын
@@bigboreracing356 Fine, but if you are going to go through the trouble and expense of that housing, then fit it with an appropriately upgraded center section, not some nondescript piece. This is mismatched.
@413x3983 жыл бұрын
@@bigboreracing356 It's a non-webbed case without through-bolts. You can bet racers that are actually using that housing as a race piece are NOT employing that same carrier. And what kind of an insult is "window licking we Todd"? Grade school? Oh, and this loser has twice as many 9-inch rears as you have fingers and toes.
@CallofDoobie5853 жыл бұрын
Did you guys know someone's suing Chevy because her ecoboost burned a certain amount of oil per miles etc. Dont ask where it came from lol. Saw it in a story
@miguelcastaneda72363 жыл бұрын
any one out there remember what maker back in 60s offered a two speed rear end
@americanpatriot2.063 жыл бұрын
There were three main manufacturers for 2 speed rear ends. International, Columbia, and Eaton. They are more commonly used on your commercial heavy duty trucks. As for the pre 80s medium & heavy duty pickups/trucks, years and models varied.
@mikepatton52513 жыл бұрын
Nice truck but I would put a different motor in it
@pauldionne16653 жыл бұрын
It will be interesting to see how long those turbos last! That little engine is a powerful engine though. The cost of one of those turbos might be the cost of another engine ? Love to see how long they last ( Twin Turbos ).
@bmstylee3 жыл бұрын
Since it's not a daily driver it's a non issue. Personally a Coyote would be cool. But availability wasn't great when they built this.
@pauldionne16653 жыл бұрын
@@bigboreracing356 wow that is truly incredible. That is alought more mileage than I expected. I have seen these turbos crap out with fewer than 50,000 miles, without the engine being abused at all. Ford had a diesel turbo in the 90's that was just poop. 35,000 miles was all 1 turbo would go.
@scootergeorge95763 жыл бұрын
How much of the Axle came from Ford?
@2511jeremy3 жыл бұрын
None the design is a ford 9" nothing was made by ford tho its the most common type because of the tail bearing on the pinion allowing for alot more hp
@scootergeorge95763 жыл бұрын
@@2511jeremy - I would call it a Curie or an aftermarket 9" Ford Design. The pinon gear is supported by three bearings and being able to set the 'pumpkin" on the bench instead of the entire axle is cool too. Lighter than a Dana 60 as well. The clips that retained the axles on the GM 12 bolt was a bogus design.
@scootergeorge95763 жыл бұрын
@@bigboreracing356 - Stock parts, Chevy 12 bolt vs Ford 9" diff. Don't know about you, but I'll go with the FORD unit. May be running a Chevy motor though... ; )
@scootergeorge95763 жыл бұрын
@@bigboreracing356 -Wow! That was stupid! The aftermarket starts with the Ford 9 inch which is vastly superior to the GM stuff. And by the way, your emotes add nothing to your worthless post. Try again.
@scootergeorge95763 жыл бұрын
@@bigboreracing356 - At least I'm smart enough to know how to spell "Stupid."
@rodlewis40473 жыл бұрын
Why are there no drain or fill plugs?
@2511jeremy3 жыл бұрын
Some customers prefer it but not many they went cheap cheap cheap
@SteveXNYC3 жыл бұрын
China looking good
@dannywilliamson33403 жыл бұрын
I thought you guys were going to ditch the Guitar Hero bit?!?
@WDMtea3 жыл бұрын
Product recognition that is always out of stock
@Mac_Made10 ай бұрын
Why? Why those wheels?
@waynecreech3 жыл бұрын
That is not a dial caliper...
@eracing94813 жыл бұрын
I feel like that bearing was way too tight
@CallofDoobie5853 жыл бұрын
Talking about the adjusters on the sides?
@eracing94813 жыл бұрын
@@CallofDoobie585 no when he spun it. It didnt roll freely like it should.
@harleybob73153 жыл бұрын
What happened to Mike Galley?
@harveylong58783 жыл бұрын
he left PN/EP
@harleybob73153 жыл бұрын
@@harveylong5878 I know that, so is he doing?
@harveylong58783 жыл бұрын
@@harleybob7315 last I had seen, mike valley had moved onto a different shop
@edwardhegarty7503 жыл бұрын
Seriously? Two passes are needed for welding the axle housing. Your single pass is marginal. your issues started with your bevel grind not being correct. About that parking brake.... Are you planning on disassembling it later to put in the rest of the mechanism?
@gernblanston49563 жыл бұрын
@@bigboreracing356 , LMAO
@damianstrochnetter97353 жыл бұрын
Great video. But, it's really annoying how you emphasize the las couple of words at the end of each sentence. Work on that and keep up the good work.
@bmxadict18163 жыл бұрын
I feel like you have really done a disservice to that truck American muscle doesn't consist of v6 engines!
@Sp00kyV0id3 жыл бұрын
You do know they had 6 cylinder engine back then right?
@noeluna58523 жыл бұрын
Could’ve gone a bit slower on the diy rotisserie. Still looks good though
@jonathansanchez20603 жыл бұрын
The video was sped up
@ahnafzahid94503 жыл бұрын
will this be 4x4 or 4x2?
@matthewmattson68813 жыл бұрын
I would assume RWD, if it were gonna be 4x4 they would have made a point out of it. Instead of an axle build bed be seeing a high HP transfer case video, or something. Who knows. Love me some all wheel launches though, would be wicked to see
@jeffatkinson68483 жыл бұрын
where is kevin
@harveylong58783 жыл бұрын
episode is ancient. Kevin hasnt been with PN/trucks in yrs
@jazzsounds81593 жыл бұрын
U should give the truck away when done.
@davidblalock99453 жыл бұрын
A procharged Ford 300-I6 would have been a far better engine than that over stressed boat anchor.
@DylanO05053 жыл бұрын
Sounds like something a boomer would say.
@pauldionne16653 жыл бұрын
With three in the tree. Now that's original. No need to be a boomer that's what the Factory made. But then they are doing it from someone else's work. Looks super COOL.
@bmstylee3 жыл бұрын
300 boat anchor is a better description.
@DylanO05053 жыл бұрын
@@pauldionne1665 who else other then a boomer wants to top out at 60 mph? Lol.
@markc76863 жыл бұрын
Way too many ads
@vsnofjohana3 жыл бұрын
If the only thing original is a cab, can you really call it a 1955?????
@pauldionne16653 жыл бұрын
In LOOKS ONLY. the rest is pure Power.
@dantheflyinman15763 жыл бұрын
Who farted
@SteveXNYC3 жыл бұрын
Watch me
@dantheflyinman15763 жыл бұрын
@@SteveXNYC lol made my day grate build by the way.
@SteveXNYC3 жыл бұрын
The welder learn from a robot in China invented by an American.
@hibiki543 жыл бұрын
Those welds look like shit, IMHO.
@eathanrichards63633 жыл бұрын
A v6... you couldnt put a v8
@gabriellindig3 жыл бұрын
I know they mean well, but this is just unholy. And when I saw them torque down the wheels with an impact driver...
@eathanrichards63633 жыл бұрын
@@gabriellindig i stoped watching
@basshead.3 жыл бұрын
1st
@chloehennessey68133 жыл бұрын
The guys sing song, specific delivery is upsetting. The pauses, nuance and inference, diction. I can’t pin it down. But he’s like a bad car salesmen went to a few courses on journalism 🤬
@shadowopsairman15833 жыл бұрын
Ecoboost are boring
@donalddavis5813 жыл бұрын
what a huge waist of time!
@Sp00kyV0id3 жыл бұрын
@@bigboreracing356 heh
@Degenerate1243 жыл бұрын
Day 79 of becoming the most subscribed KZbin channel with zero video’s so I can live the life. 💪🏼🙎🏼♂️🤙🏼.
@willemp64323 жыл бұрын
I would like this so much more if it was like all over the world..... Metric... Ⓜ