Factory reset Brother HL-2270dw Printer HL-2240 HL-2230

[@93karamgill]

This worked like a charm. I was trying to reconnect to a new router after having moved to a new apartment. Did the reset, followed by holding down the WPS button on my router and the push button on the back of the printer. After a few seconds, a page should print out the new connection. I hope that helps anyone stuck trying to do the same thing.

[@AirDyran]

Tutorial starts at 0:22 and ends at 1:00 1. Open up top front panel. 2. Turn on power switch WHILE holding green GO button. 3. Three lights should be lit, let go of the GO button. 4. Press GO button 10 times in succession. 5. Close cover. 6. Press GO one last time.

[@303electronics]

Thanks

[@tracyhill7339]

Oh my god! I've tried everything and nothing made sense - turning power off and then holding Go button - but your directions were PERFECT!!! Turn power on WHILE holding green GO button, etc.! Amazing. Kisses and hugs!!!

[@emzywillrich7243]

THANK YOU, THANK YOU, THANK YOU!!! I thought I was going to have to purchase another printer. Your instructions worked beautifully.

[@kristensvensson5568]

Thank you for the help with this issue. Saving printers from landfills and people from stress!

[@303electronics]

Thank you so much for your comment. Very encouraging. Have a good day!

[@kyrareneeLOA]

Thanks so much.... by opening up the backside found paper that got caught and couldn't be seen from the front. Your video did help me, so thanks!!

[@BigMoney10x]

Thanks… fixed it just like your video! Thank you for your service to humanity… and the planet!

[@briwade8540]

Yo!! Thank you for this! I was getting frustrating! But this saved me. ❤❤❤

[@303electronics]

I'm glad you got it to work. Thanks for the feedback. Have a great weekend!

[@Tasman9]

Thanks so much i was struggling with error ts-07 but your reset method solved it for me. Big thanks

[@itz4u]

Hi, very informative video. It worked up to point. I have a Brother HL 2040. I did as you did in your video but all that happened was that after I closed the front panel, and click the 'GO' button again, the printer goes into warm up mode , the Yellow light goes on for the drum and toner and the rollers start rolling and doesn't stop. When I tape on the 'GO' button the red light make a clicking sound for every tap but nothing happens except the rollers in the back and top just keep rolling and the Yellow toner and drum stay lit. I have to unplug it and repeat it over but the same thing happens Thanks It went from all lights on till just the problem I have now so I know something progressed

[@raymondng3763]

Thank you so much. You have just resuscitated my HL-2270DW!

[@nara49veera12]

Thank you. It worked for my 2240D. You helped to reduce one more electronic garbage !

[@deanlindsay3286]

So helpful thank you. Cleared a persistant Paper jam error (with no paper jammed).

[@303electronics]

Glad it helped!

[@tremayne3]

Would this process also clear the memory of the printer?

[@rahulrathan]

Thank you for your service to the society.

[@303electronics]

My pleasure! Have a great weekend!

[@PatsUnmadeBed]

Thanks. The printer is now working smoothly.

[@303electronics]

That's great! Thank you for sharing. Have a great day!

[@kaitsang7020]

Your reset does not clear the static IP address set on my 2nd hand HL-2270DW printer. Sharing what I found.... Actual factory reset (clears IP address settings) is: (1) Turning the printer off (2) Holding down the "GO" button and turning the printer on (3) Keep holding it down until the top three printer lights come on (Toner/Drum/Error) (4) Release the "GO" button (5) Press the "GO" button 6 times in succession Also to print out Printer Status (3 pages): Press the "GO" button 3 times in succession The default password for using BRAdmin is "Access"

[@jollibee027]

This worked for me! Thank you!

[@balasekar2565]

Hi. I have hl-l2300d. My drum light is blinking light yellow. I tried drum reset multiple time and still no luck. Any advice is appreciated thanks

[@Dilbertic]

You may need to do a few things, if you are using ethernet, watch the back lights at the port when the printer resets and the lights dont turn on next to the ethernet cable then it didn't reset correctly. I had to do the toner then unit reset for the ethernet to turn back on. update The printer will default to wireless after some firmware updates and the ethernet port will be turned off !! If the ethernet port is turned off try the above and if that doesn't work do the following; Turn off the power to the printer, hold down the GO button and continue to hold it down while you turn on the power to the printer, when the 3 lights on top of the printer turn on, release the GO button and then press the GO button six times, the printer will reset.

[@303electronics]

Thanks for the input! This will help someone for sure. Have a great day!

[@Dilbertic]

@@303electronics I added some updates, messed with the printer for 2 hours last night thought it was dead ethernet port..

[@arabianights]

I concur on this - about firmware update messing up printer. at some point when I upgraded firmware on my HL-2270DW printer, afterwards it hadn't be able to stay connected to network anymore via ethernet to my router. finally I had enough and got around and called Brother for troubleshoot, they told me to print test page showing its settings, it has both ethernet and wifi enabled :o , by pressing 'Go' button 6 six times seem to reset network, with only ethernet connection active, however a few hours later it got disconnected from home network again. this time I did factory reset according to this video, followed by tuner reset, drum reset; it seems to fix the problem, 2 days later at time of writing, the printer is still connected to my home network.

[@byronbunning7877]

Hey, do you know how to do this on the HL-6180DW? Cheers

[@periclespatrick]

Good afternoon! after the reset process, the printer turned off all the lights and did nothing else! What can it be?

[@303electronics]

Hi. Sometimes you may need to unplug the printer, plug it back in and press power button.

[@animatter1696]

I turned off the printer during while it was printing, and now it shows error light. I tried resetting, but it didn't help. Do you know how I could fix this?

[@303electronics]

Did you check all paper passageways to make sure that there is no paper anywhere? Pull the toner out, check there, and open the back door of the printer where the fuser is and also check there. Then restart the printer. Off, then on.

[@elizabethgray6522]

@@303electronics OMG, yes!! stupid I didn't think to check for a paper jam. THANK YOU

[@evgenyfiks9243]

Hi, I followed all steps but the error still blinking. What to do?

[@jonorlick6168]

You're a lifesaver!

[@303electronics]

I'm glad it was helpful. Have a great weekend!

[@relic46]

Thank you. All fixed now

[@303electronics]

Great! Thanks for the feedback!

[@johnburke9352]

Unfortunately, this did not work for me. I have an HL-2240 and right after I press the Go button 3 times it never resets and attempting to press the Go button after never lights up the Go button anymore. My PC restarted during a firmware upgrade .😔 Ever since any time I turn off wait 8 secs turn on the printer again none of the lights come on but for a 1⁄2 sec and the printer never makes any startup sounds. At least with the factory reset attempts, I can get lights on the display, just never restarts.

[@303electronics]

I'm sorry you are having trouble. Thanks for sharing.

[@kaitlynnickels9647]

The exact same thing is happening to me with the HL-2270DW! Except I stupidly turned off the printer during an update..

[@FLHouseAccount]

@@kaitlynnickels9647 guess we are just SOL. Let me know if you ever find something that works

[@andrew5032]

My printer says error what do I do

[@inlightenedbeing]

Brother MFC 7820 it is saying the door is open but it is closed how do I fix the error message?

[@milafoo9469]

My HL-2270WD didn’t worked on printing, it keeps saying error. any one can help what to do?

[@303electronics]

Make sure you are selecting the correct printer. There may be 2 of the same printer model installed on your computer and only one of them is going to be the one that you have. What is the error message?

[@Shasha8674]

I pushed the cancel button too strongly to try to tell it to stop printing so may have hurt that button so now it is on error/paper, but I fixed the paper already. It still is not working.

[@yujiehu6825]

I held the go button but nothing happened

[@bihinix]

awesome. now how do i find the WPS_pin so i can finish the setup? We have updated our router so havent been able to get this connected.

[@beingsneaky]

If you mean the physical wps button it is under the usb plug

[@bihinix]

@@beingsneaky no when i go to connect it to my network i get a box saying enter the WPS pin for your printer? cant find that anywhere on the printer

[@beingsneaky]

@@bihinix hmm press and hold the wps button on the printer for more then 2 seconds it will print out a sheet with the pin

[@bihinix]

@@beingsneaky Thanks! i did this and it printed a page with the pin code so i thought yay. i put that number in and it says connecting, then says it is the wrong pin and to try again. The printer worked fine on our old modem, we upgraded to fibre with a new modem so i thought by following this video i could reset the old set up? this all worked as shown i got the three page printer settings pages but still it wont connect to the network. should i try anything else or give up? the printer does work when connected by usb to my pc but i dont want everyone disturbing me to print.??

[@beingsneaky]

@@bihinix I got mine to work by pressing the wps on the modem first... them pressing the wps on the printer for less then 2 seconds a quick jab. Then it connected takes awhile will spit out a sheet saying connection ok????

[@c.caruso7010]

I have followed these instructions four (4) times. Each time the printer starts again, but states the printer is disconnected. The first time I pulled out the USB connector and put it back in. STill not connected. I tried this three more time, making sure I did not move the printer so as to not disconnect it. Nothing changes. anyone have any additional ideas? Thanks

[@bihinix]

this was the same for me. i deleted all set up on computer settings (so delete device from printer settings) then i followed these instructions: support.brother.com/g/b/faqend.aspx?c=ca&lang=en&prod=hl2270dw_all&faqid=faq00002794_004

[@bihinix]

i had no joy in steps 1-3 but it all installed from step 4

[@KpxUrz5745]

After doing these steps the error light comes back on.

[@303electronics]

Could be a differnt problem. What is the error message?

[@KpxUrz5745]

@@303electronics Thanks for reply. Problem solved. Had removed the jammed paper. There had also been driver problems since moving printer to another computer and location, so those issues threw me off. On further checking, found a 2nd jammed sheet down deep in the machine. Now it's ok.

[@nausheenzubair1184]

hey brother I love you.

[@aleadiann]

Thank you!

[@stacyhackney6100]

Thank you

[@nanitaylor8073]

my toner light wont go away no matter what i do. ive reset this thing no less than 10 times. i will never purchase another brother printer. this thing is a piece of crap.

[@303electronics]

Did you get a new toner? Also, could it be the drum that needs resetting, not toner?

[@om73982]

Printing slow

[@shreepaldupare8566]

Problem solved

[@Mendtat111]

this is wrong

[@lorraine.-.]

I’ve got a 2340dw - not used for a while but turned it on & am getting maintenance 4 error. Tried trouble shooting tips but buttons are all non responsive- any ideas what is wrong or is it ready for the scrap heap?

[@303electronics]

Brother printer "Error 4 Unable to Print" error usually refers to a mechanical error somewhere in the printer. Remove the toner and drum and see if there is anything in the way/ Also, try spinning the rollers on the drum and toner to make sure they are not stuck. That may cause the error. Check the back of the printer where fuser is and see if there may besomething thre or out of place. DO NOT TOUCH ANY ROLLERS WITH BARE HANDS. Hands will leave skin oils and cause print quality distorion. Use clean disposable gloves.