Failure Fatigue Analysis in SOLIDWORKS Simulation

[@amr.a-m8350]

Good video but . I hope to know at 17:21 the number of cycles is approx. 10,000,0000 larger than 7000000 for the second part which indicating failure will be occurred especially using 64 % from the default cycle.

[@divyeshdodiya7853]

Hey.. I made one plastic pot ni solidworks I want to check how many load is good for my pot in inside and pot shape remain as before I want to check how many load I give in it so it will break ... Can u please guide me.. I'm waiting for your positive response... THANK you

[@ernesttan8090]

Is the location and magnitude of stress the sole determinant of fatigue failure? Isn't this fatigue analysis simply applying a scaling filter to the stress heat map?

[@OnlineStudyLearn]

can you please tell me difference in contact set and component contact in simulation.

[@mahsahamidpour5297]

Can I have the drawing file of the crank shaft? Thank you

[@divyeshdodiya7853]

Hiii I saw yr video it's really useful bt I hve a question what's meaning of cycle(N) like u put 100000000000 and or but what it's indicate day, year, hours, second,......

[@alexfryproductions]

thanks for the video. how can you define the max and min stress for the fatigue cycle. i noticed you only input the mean stress?

[@Alignex]

+Alex Fry - In this case we are actually setting up a Static study that calculates the Max stress everywhere. Then in the Fatigue study we set the number of cycles and Loading ratio. In this case I did a zero based load which gives me a loading ratio of 0. The loading ratio is defined as the Min Stress/Max Stress. So the Static study calculates the Max stress at every node and with a load ratio of 0 the software calculates the Min stress as 0. From this the software also determines the Mean stress from the equation Max+Min/2. So the Mean stress calculated from this is actually Max/2 which is calculated at every node. Thanks, Eric

[@andyarceye]

Very informative video on how to set up the simulation to compare different designs. It is a good way of testing multiple designs to see which is most likely to last longer. However the numbers are only relevant for comparison testing and of no use to real life. But more important,, Why is the wrong side pedal being used... It's bugging the hell out of me

[@Ciupremo]

Ye that pedal hurts

[@EdwinMedina147]

Hi, great video. I would like to know why I get a lot deformation in my part when aply force, knowing that it does not happen in real life? I fit my material Aisi 4340 steel.

[@parthmittal7658]

go to edit definition of stress/displacemtn or whatever study result and choose the "true" tick box instead of automatic which is pre-ticked. u will get the right deformation

[@ahuizotllopez7172]

how do you get the s-n curve of 6061???

[@tacticalvictorian5371]

by a special dark magic called "engineering data".

[@NguyenHuuLinh_]

i have a question. for example that failure due to fatigue is likely to occur after approximately 16,510 cycles. but i don't know 16,510 cycles approximate how many hours or days?. thanks alot

[@91722854]

if you know the frequency, you just need to divide cycles by the frequency to get time (s) and then finding out how many days, months etc

[@LuisFernando-hy6gn]

It depends on the operation of your part. The frequency or rotational speed and hours of work per day

[@chetnaprajapati9483]

how to sync two circle example:- one circle dia75mm and secound circle dia1000mm dia1000mm (1000mm-100mm=900mm) so change dia 75mm change (75mm+100=175mm) mins i one circle dia minuse so secound dia pluse is value how create बहुत बढ़िया पर मुझे ऐसा काम कुछ इस तरीके से करना हो तो कैसे करे कृपया बताये जैसे के एक circle 75mm dia का हे और दूसरा circle 1000mm dia का हे अगर में इन दोनों में से किसी की भी साइज़ बदलता हु तो वो एक दुसरे में pluse minus खुद्ब्खुद हो जाये जैसे के अगर में 75 mm dia में 25 mm जोड़ता हु तो वो dia 100mm हो गया पर जो दूसरा dia जो 1000 mm का हे वो 975mm खुद्ब्खुद हो जाये बस ऐसे कोई भी एक dia अगर pluse होता हे तो दूसरा dia खुद्ब्खुद minuse हो जाना चाहिए और कोई भी एक dia minuse होता हे तो दूसरा dia खुद्ब्खुद pluse हो जाना चाहिए हा पर जितना हम pluse या minuse करते हे उतना ही value एक दुसरे dia में pluse minuse होना चाहिए कृपया करके ये बताये ये कैसे हो सकता हे solidwork में ?

[@jeeeeeeva]

and can u please share the SN curve data for the aluminum 6061-T6 till 10000000 cycles i got a SN curve through this link www.osti.gov/scitech/servlets/purl/10157028/ but not sure about its correctness.

[@masoncnc]

um ah um ah um ah um ah, ah, um um