please the PAS is not working with this controller ? what is the reason , i used 3 different pas and not working , thank you
@gadh987 ай бұрын
hi tnx for the guide. when i in the settings menu (p-settings) , and i long press the power button, the "A" in the bottom line changes to "D". do you know what is the purpose of this mode A/D ?
@sktv1112 жыл бұрын
I've lost a rew numbers 8 12 n so on how do I get my zero 10x bk to normal
@nahariguy63 жыл бұрын
Hey please help me, i have the zero 10x and Under the cable shield in the handlebars there is a wire inside which there are 3 wires inside of him: red, green and black and they were wrapped in white tape in a bad way so I wanted to replace the tape and then suddenly the scooter stopped working and did not open again... please tell me what to do if you .
@FalconpevSg3 жыл бұрын
We can’t help without pics. Pls email us at sales@falconpev.com.sg
@fighter67 Жыл бұрын
hallo habe faulty comms between controller and LCD was kann ich machen danke für die hilfe
@MaeRiGee5 жыл бұрын
I don't have P8 power level. But the P15 is 100. By any chance the power level is P15? Then again i don't have Cut off voltage. Kindly advise.
@jorenpatrickflores5706 Жыл бұрын
How to get my zero10x taillights standby? If I hold the mode button to turn on the lights. It lights the front only. Back light works if I just press the breaks.
@E69apeTheMatrix4206 жыл бұрын
p17 is Cruise mode you said if you want cruise set it to 1 and if you want cruise set it to 0. that was a confusing bit? how does the cruise control work please? kind regards.
@darkwish30x5 жыл бұрын
@M. Nurhaikal Hold the same speed for 4-5 seconds and it will be on (signaled by a blue icon on the dash).
@zingzing776 жыл бұрын
someone had a problem error 09 (contoller) in his lcd for his scooter, What is the problem ? how to resolve it or réinitializing it please ? he can not use it now same scooter was dammaged
@snake89455 жыл бұрын
How the electronic braking works ?? Thanks
@instars20273 жыл бұрын
2 years ago I remember I was able to turn on "6kmh cruise" mode for my Zero 10X by pressing and holding some buttons. It was very useful when walking and pushing the scooter, but I don't remember how exactly I enabled it. Do you have any information how to enable this walking cruise mode?
@haskarmilayayang343 жыл бұрын
How to change speed,i buy bolzzen dynamo, original just can go 19kmh,i aready set P8 100,but nothing change just go 19kmh..pls advice
@ryzjazz9884 жыл бұрын
New batch of zero8v2? What should be default number of magnets? Based on the video it should be 30 but i receive it 28 only please confirm which is correct
@shlomodadash336 Жыл бұрын
I have Regen on but when I press brake it is only stoop giving power to the motor and the wheel is still rolling
@sarahp82314 жыл бұрын
What do to if the charger light don't turn from red to green even though the step is fully charged (i can see that on my screen and my voltage is 65. I have a 60V). Can it do damage to my battery? Thanks!
@rickmark83256 жыл бұрын
Can I settings each mode of max speed? e.g. Mode 1(low) is 10kmh , Mode 2 (Mid) is 20kmh, Mode 3(high) is 30kmh. How to do it??
@fingerkol47905 жыл бұрын
P08 - Power Level (0-100)
@grigorisk94275 жыл бұрын
If I put volt from 48 to 60 the top speed will be higher? And can it does problem to the motor? What if I change watt I will burn motor?
@nosgold68616 жыл бұрын
Hello, if I set to 36V instead of 48V on my Zero 8 I will have more autonomy ?
@xorbe25 жыл бұрын
No it will probably cut out a lot sooner
@Hijo-del-Chico Жыл бұрын
hello. I have an electric scooter and it has the same display, or is it very similar. I would like to know if you could help me with a question that I have. Today when I was going to work, the scooter lost power, but when I stopped, I saw that the display and the ignition were still on, but the accelerator did not work. So I turned everything off, and turned the contact back on, but when I went to turn on the display, it doesn't respond. then at home, I was able to see and verify that the current reaches the display connector perfectly. . Is it sure that the display will be the problem? I also see that there are many models that are the same or very similar on the outside, how can I know if it will work on my scooter? Thank you
@FalconpevSg Жыл бұрын
You cannot simply buy any display, they have to be synced with your controller. Go back to the person you bought from
@Hijo-del-Chico Жыл бұрын
@@FalconpevSg Thats the big problem,. since I bought it in AliExpress, and then the store stopped selling in AliExpress, so I can't use the same store that I bought the scooter.. So... if I buy one with 6 pins, and I review the cables, each one in its color... it won't work? thank you
@FalconpevSg Жыл бұрын
@@Hijo-del-Chico no it’s in the software
@nahariguy63 жыл бұрын
Hi, i have a question, when i enter the P settings and long push the on/off button, the letter ''A'' on the bottom left changes to the letter ''d'' And I wondered what it does... so if you know please tell me :)
@RICORSL3004 жыл бұрын
Hi, for the Zero 10 X what's the regular settings for P15? Is it 42 or 44? Pls advise
@scottireed20939 ай бұрын
Did you find an answer? I'm struggling
@darkcrystal4383 ай бұрын
@@scottireed2093 Mines set at 42
@scottireed20933 ай бұрын
@@darkcrystal438 thank you for replying!
@darkcrystal4383 ай бұрын
@@scottireed2093 no problem mate! Im currently setting the steering tension on my 10x right now ha ha.. was a bit stiff.
@QUAD84 жыл бұрын
Is it possible to use that lcd to gyro corp (gyro g air plus scooter)? My lcd has no display and i want it to replace that kind of lcd...tnx!
@agennello14 жыл бұрын
What is the red (!) on the top right when you hit the brakes Zero 10X? I am not sure my electronic brakes are working.
@FalconpevSg4 жыл бұрын
Hi Red Exclamation mark means brakes are on!
@DanceySteveYNWA3 жыл бұрын
It means your brake lights are flashing in hazard mode
@patmccaffery15434 жыл бұрын
If I'm in eco mode, can I switch to turbo mode by pressing the turbo button or do I have to go to gear 3 first..??
@daralee78795 жыл бұрын
Does electronic braking on this actually work? I didn’t see any difference when I tested it up on the chair so the wheels can freely move and I didn’t notice any difference after letting go of acceleration whether electronic braking actually works, I went through level 1 to 5 in P11 and didn’t see any difference
@daralee78795 жыл бұрын
Ahh I can confirm it does work. Once you get up to higher speeds and you pull the brake lever lightly the regen brake kicks in and you can hear the motor whine
@miguelvera97062 жыл бұрын
How can you adjust the batterie level.?
@liad700 Жыл бұрын
When i try to go into P menu it shows me a big 50 number and asks for some kind of 4 digit password, which i dont know
@445crompton5 жыл бұрын
Thanks for the heads up! One question when my scooter is under load the battery shows it near empty, when I release the throttle it climbs back up? Is this normal?
@husse8435 жыл бұрын
i can tell u that mate! when u use the throttle at 30 % battery it shows you, if u hold this acceleration u get this far . but if you now take your throttle at 70% it shows you how long u can get at 70% throttle, sorry for my bad english !!
@modzmetropolis95582 жыл бұрын
@@husse843 Translation 3 years later = If you hold your acceleration at 100% the voltage will drop as your sucking more juice and will show you how far you can travel at 100% throttle. If you hold it at 50% throttle instead of 100%, it’ll change and calculate the new distance you can travel based upon power consumption being used from pulling down on the throttle. Lighter throttle = less juice being sucked out = more distance available to travel before battery dies.
@reuven201011 ай бұрын
@@modzmetropolis9558 actually there are no calculations or anything fancy, the reason the bars drop is because they are based on current voltage if you are using the throttle you are putting load which drops the voltage
@xorbe25 жыл бұрын
Thanks, goodness I couldn't figure out how to turn on the headlight.
@chrisizme25 жыл бұрын
After you change the settings, does it automatically save or you have to readjust every time? I didn't see a save feature after you exit the settings menu at the end. Thank you for the informative video!
@AtomicWaffle4 жыл бұрын
It saves
@abundantharmony Жыл бұрын
Is this the same throttle as the jue Shuai x48?
@FalconpevSg Жыл бұрын
Model is QS-S4
@d.rascals49413 жыл бұрын
P-Settings are all the same on all brands as long it's QS-S4?..My eks brand is DOUBLE D VA40P also QS-S4 throttle.
@FalconpevSg3 жыл бұрын
Yes all the same
@meskafe5 жыл бұрын
How to eliminate the 25km/h speed limit? from all3 modes with P08 to 100 only get 25km/h
@raulsolera60963 жыл бұрын
How can i see the remaining voltage in the display? The bars are not accurate. ¿Cómo se puede ver en el display el voltaje restante de la batería? Las barritas no son nada exactos.
@bosskenjei71344 жыл бұрын
I know this been so long ago.. Can ask why my scooter battery guide is allways 100% I mean full green bar but . I'm driving then suddenly batery empty..
@honeymaemaceda17504 жыл бұрын
Sir may i ask i have a problem with my parameter, the battery indicator is blinking into a lowbat but the volt is 41v, i charge its only 3 hours then the light indicator on charger is green, but still the icon of battery is still blinking,but the scooter is working and running, i want to send a video to you but cannot here, please help me thank you.
@dubaiofw4 жыл бұрын
check ur controller voltage...if 36v ....in P3...change to 36.....
@MorningSessionsTube5 жыл бұрын
Up to which speed does P12 settings make a difference in acceleration?
@AtomicWaffle4 жыл бұрын
Mostly at start
@luciddreamer60003 жыл бұрын
Does anyone know if the QS-S4 LCD throttle unit for this Zero 10X scooter will be compatible with Mototec Thor 60V scooter? I am looking for a spare QS-S4 for my Mototec scooter and they are sold out everywhere.
@geestang26623 жыл бұрын
So 10x when receiving out of the box it's not set yet so I have to set the controls before riding
@nandotec122 жыл бұрын
Hey bro, What is the configuré to E5?
@borisevraev81902 жыл бұрын
Hi, after the long press on power and mode buttons i get screen with password "SO" do you know what is the pass ? TAI
@FalconpevSg2 жыл бұрын
It shouldn’t have that
@ormaza4 жыл бұрын
Do you know how desensemble conector to wire from controller? It is view in video alltime
@sujanshrestha42704 жыл бұрын
I brought a this set controller but when I connect the wires( only battery wire and 3 phase wires ) "warning sign" blink and when accelator is increased "countinous speed " signs appears, any one can help me please.
@golani44555 жыл бұрын
How to clear the odometer p16? Thanks
@ozzythegr84 жыл бұрын
Thanks for this video! When I try to get the P program menu it goes to a menu PO from there I can’t access to the program menu! Its posible that my scooter has that menu locked?
@FalconpevSg4 жыл бұрын
Oswaldo Hernandez where did you get your scooter from
@ozzythegr84 жыл бұрын
Falcon PEV from israel! It’s another brand but the same controller (QS -S4), should I ask the seller if there is a password? Thanks for your answer!
@paulfonfonocho56183 жыл бұрын
Please to claim a heal i want to know Please because I am not able to claim the heal with my 0-10 scooter electric
@krawutzelgesicht4 жыл бұрын
What exactly does the high beam symbol do when hold mode button ? Is there a cable from the controller that is switched on ? If , what color and voltage ? Thx
@liteglow20004 жыл бұрын
It does nothing :)
@vipermanx994 жыл бұрын
thanks for the info but is there any added setting on the Zero x11???
@liteglow20004 жыл бұрын
Can anyone help me. I got this LCD and controller. I got 3 modes. But I need to start slowly. Why is it not possible to change speed? Why is is only 3 speed settings? It makes no sense.
@shimonsd23622 жыл бұрын
halo can you halp my i need the pin cod to p setting please my qs s4 thenks
@ziedonispetrovs54804 жыл бұрын
Is there a way to display riding time? Additional to voltage and trip distance.
@victorciobanu15 жыл бұрын
I managed to set a password using s1 function that i cannot remember. any idea how to reset it ? or is it even possible?
@Rosa_AI5 жыл бұрын
I managad to figured that out myself it took me a while , 1. turn the scooter on and enter the password you have so it will go into the on state. 2. hold power button and mode button together (you'll get a popup for a password) 3. enter "1111" 4. it will ask for a password again this time enter "0000" 5. this will now make your scooter without password and should allow you to turn it on and off without pass. if you need help go ahead and PM me,i can always make a video if needed.
@jfoldger11844 жыл бұрын
Florian De Graef make a video please
@liambreust894 жыл бұрын
9221 then hold power
@markp33513 жыл бұрын
How does the Eco/Turbo button differ from the gear select?
@defile6675 жыл бұрын
How long do you have to hold the throttle down before cruise control is engaged?
@fosy9527 ай бұрын
9 seconds
@haroldjacinto72572 жыл бұрын
Hello I Have zero 8 my scooter is not changing gear.
@FalconpevSg2 жыл бұрын
Controller issue
@idangabai19552 жыл бұрын
Hello what is the Code for Zero 10-Z ??
@mahidm18043 жыл бұрын
How i accidentally changed p07 setting. How doni undo it
@yohvh4 жыл бұрын
I've had send the following:: P01: Backlight brightness, level 1 is the darkest, level 3 is the brightest; P01 defaults to 2 P02: mileage unit, 0: KM; 1: MILE; P02 defaults to 0 P03: Voltage level: P03 defaults to 60V P04: Sleep time: 0, do not sleep; other numbers are sleep time, range: 1-60; unit minutes P04 default is: 10 P05: Boost gear: 0: 3 gear mode; P05 defaults to 0 P06: Wheel diameter: unit, inch; precision: 0.1; P06 default is 11 P07: Speed measuring magnet number: range: 0-255; P07 default is 30 P08: Speed limit: Range 0-100km / h, P08 defaults to 100 P09: Zero start, non-zero start settings, 0: zero start; 1: non-zero start; P09 defaults to 0 P10: Drive mode setting 0: Power-assisted drive (The power-assisted gear determines how much power is output. The handle is invalid). 1: Electric drive (drive through the knob, the power assist position is invalid at this time). 2: The power drive and the electric drive coexist at the same time (the electric drive is invalid in the zero-start state). P10 defaults to 2 P11: Boost sensitivity setting P11 defaults to 3 P12: Boost start strength setting P12 defaults to 3 P13: Type setting of power magnetic disk P13 defaults to 12 P14: Controller current limit value setting Range: 1-20A P14 defaults to 12 P15: controller undervoltage value P15 defaults to 49 P16: ODO clear setting Long press the plus button for 5 seconds, ODO clear P16 default is 0 P17: 0: Disable cruise, 1: Enable cruise; Auto cruise is optional (only valid for No. 2 protocol) P17 defaults to 0 P18: display speed proportional adjustment Range: 50% ~ 150%, P18 defaults to 100 P19: 0 gear enable bit, 0: with 0 gear, 1: without 0 gear P19 defaults to 1 P20: 0: No. 2 protocol 1: 5S protocol 2: standby 3: standby P20 defaults to 0 So the P11 is regen brake or something else?
@Highfocus894 жыл бұрын
Can you explain what p18 does? When I got my mx60 my settings were different..p18 only went upto 100. It is possible that I accidentally programmed my LCD controller for a different scooter? All my settings have changed. Is there a way to change it back?
@dennishurd6199 ай бұрын
How do you reset the time
@squal69lyonlaurelli725 жыл бұрын
Bonjour quels sont les meilleurs réglages pour une zero10x merci beaucoup je suis en france
@merdenoms44 жыл бұрын
Could you please tell me what does it mean the exclamation mark on the left side of the lcd?
@FalconpevSg4 жыл бұрын
Lucy Diamond it’s nothing. It will go away after a while.
@bobbyhooper67283 жыл бұрын
whats the code for SO Mode
@maeaballe7834 жыл бұрын
Where can I buy this universal LED?
@FalconpevSg4 жыл бұрын
Mae Aballe here you go www.falconpev.com.sg/products/zero-8-throttle?_pos=1&_sid=1d8f9ce05&_ss=r
@maeaballe7834 жыл бұрын
Falcon PEV | PAB PMD E-Scooter E-Bike Shop thank you so much
@ChuppyCata3 жыл бұрын
I messed with the programming stuff and i almost died on it. Is there any way to reset it to factory settings or something? Scooter wouldnt stop and brakes are really violent. Please help!!!
@DanceySteveYNWA3 жыл бұрын
Did you do the reset?
@ChuppyCata3 жыл бұрын
@@DanceySteveYNWA thanks but i figured it out. I activated the electronic brake by mistake
@DanceySteveYNWA3 жыл бұрын
@@ChuppyCata oh, I was going to help you with it, but if you're good, no problem. Safe riding.
@toddlauretteHabsforlife4 жыл бұрын
Hey, how can i find out what my cut off is? Like when my voltage gets too low, i believe it cuts off when the battery reaches a certain percentage. Anyone know how to check that? Thanks in advance.
@tedtedsen2694 жыл бұрын
go in to the p menue and volt on my scooter not zero i can adjust the cut off higher and when it cuts i have spare power to take me home like a reserve fuel tank WARNING don adjust it lower you wil have more range yes but it can damage the battery
@CarleyEspritPhilip3 жыл бұрын
Did you find out?
@toddlauretteHabsforlife3 жыл бұрын
@@CarleyEspritPhilip Yah, mine was aet at 42 and the actual cut off i believe it 41, or maybe 40, u could google it to be sure, but mine is a 52 volt, and the cut off is at 42. Have fun and ride safe!!
@hashedhakahol3 жыл бұрын
Help i cant find the 4 digit code
@mikshooter25364 жыл бұрын
can i ask sir ? is it possible to change the lcd ? for minimotors lcd?
@FalconpevSg4 жыл бұрын
100 % Pro nope
@mikshooter25364 жыл бұрын
Falcon PEV and why sir ? thank u
@klunk645 жыл бұрын
i need a video on how to put a electric voltage monitor on this lcd ...you already have one for the older 8 but i have the newer 8 with this controller
@nahariguy63 жыл бұрын
what does it mean cut off voltage? and why mine set to 39? (P15)
@FalconpevSg3 жыл бұрын
it means the lowest battery voltage that the controller can support.
@nahariguy63 жыл бұрын
@@FalconpevSg thanks
@swave12342 жыл бұрын
My LCD don't don't turn on the power button won't work. I bought a new LCD and it still don't power on what's the problem of my zero 8x please help
@FalconpevSg2 жыл бұрын
Can your scooter charge?
@swave12342 жыл бұрын
@@FalconpevSg no it won't charge either
@FalconpevSg2 жыл бұрын
@@swave1234 so it’s not the lcd it’s the battery
@swave12342 жыл бұрын
@@FalconpevSg so my battery is broken? But I only used the scooter for 1 year
@swave12342 жыл бұрын
Do I need to buy new battery?
@RICORSL3004 жыл бұрын
I think someone change my P15 settings, I need to adjust it again to the factory default for P15, what's the default for Zero 10x. Thanks for the help
@FalconpevSg4 жыл бұрын
hope you figured it, however if its not done yet, please do send us a video through whatsapp or email at sales@falconpev.com.sg
@victorciobanu15 жыл бұрын
when i enter programming mode i get an S0 message and it asks me to input a 4 digit code. any ideas what is the default code? help would be appreciated
@victorciobanu15 жыл бұрын
it's 6666 for programming... don't type 1111 as you will have to set your power on password...i forgot mine :( i'm locked out.
@baloute45844 жыл бұрын
J’ai les 0000 au démarrage Comment la débloquer???
@D.hobbyist3 ай бұрын
19 makes it so theres a gear zero so when you hitt the trottle the scooter wont move try it out😊
@baanteelanka-theupsidedown82445 жыл бұрын
hello. what is the expected range for the 10x in a dual engine mode and speed between 40kmh and 55kmh?
@kindzius5 жыл бұрын
Baan Teelanka - The UpsideDown House of Phuket 20 km max at this speed, I make about 50 km,average speed 27km/h
@baanteelanka-theupsidedown82445 жыл бұрын
@@kindzius thank you for sharing. can I reconfirm. you have a zero 10x and with double engine on and aggressive riding you only do 20km on a full charge ? and you reach 50km in which driving mode? single engine low speed with ECO off? I do 30km in dual engine. and 45 in ECO mode. I have complained to shop they said is below standards. they sent me another battery I changed but is exactly the same. now waiting for a resolution
@kindzius5 жыл бұрын
Baan Teelanka - The UpsideDown House of Phuket Yes,I have 10x with dual engine and if you drive agressive with both engines I get 20 km,if you drive with one engine 95% and use both engines when you want to climb to hills you will get about 50km speed about 25-30 km/h. P.S. my weight is 98 kg
@chrisandshazza012 жыл бұрын
I’ve gotten 83km out of a charge around Perth (Australia). It was very relaxed riding on cycle ways going slow. Was a great days cruise along beaches, rivers and cycle ways🤘 I’m 98kg
@Highfocus894 жыл бұрын
Hi falcon I really hope you can help me as my vendor isn't being very helpful :( So I bought a mercane mx60. I tried to unlock the full speed and I believe I made a mistake as the settings are different now. P18 only used to go to 100, now it goes to 150. I am wondering. Could I have accidentally programmed it for a different scooter? Althought I have changed the speeds it feels slower and more sluggish than when I first got it and the speed (p8) was set to 35 :( Also, sometimes when I turn it on or press buttons I get a red exclamation! And a "e" comes up then goes away. Sometimes I set the settings and they will change on their own. It is a really heavy scooter and now it barely moves in single motor Please if anyone can help I would really appreciate it. Thank you
@zuheir5354 Жыл бұрын
did u get a response on how u could reset the entire scooter? please help
@АртемРоманихин-х3р5 жыл бұрын
How to enable electronic brake on x10 ? I set P11 to 0-5, all not working :(
@FalconpevSg5 жыл бұрын
Артем Романихин because yours is not the zero 10X
@russellphan62603 жыл бұрын
Do you know how to reset the red wing standard LCD?
@FalconpevSg3 жыл бұрын
What’s red wing
@russellphan62603 жыл бұрын
@@FalconpevSg the LCD on the red wing scooter
@Saitama-nu6jf5 жыл бұрын
What's the Voltage level of Zero 8 V2 (with 13ah battery) and its Controller cutoff voltage? Thanks!
@Saitama-nu6jf5 жыл бұрын
Never mind, just found it. It is 48V and the cutoff is set to 39.
@kerwindapog5 жыл бұрын
@@Saitama-nu6jf Can you tell me how did you find it. i have a 10x 52V. what is the cutoff of a 10x? Please
@jfoldger11844 жыл бұрын
Thanks for that comment, I accidentally changed it on my zero 8 the other day and could find the default
@jfoldger11844 жыл бұрын
What does voltage cutoff mean exactly?
@BudgieFan1014 жыл бұрын
Very helpful, thankyou.
@FalconpevSg4 жыл бұрын
David Michael thank you!
@samier094 жыл бұрын
thank you so much. just received my 10X.
@carlamor3233 жыл бұрын
Help: battery bar empty even when I am fully charged
@FalconpevSg3 жыл бұрын
What scooter do you have
@Mario-nm5dr2 жыл бұрын
My headlights and horn won’t does anyone know how to fix ?
@FalconpevSg2 жыл бұрын
Horn? There isn’t a horn function in the 10X
@witbk8885 жыл бұрын
How to max Speed and Power? P12 only?
@kerwindapog5 жыл бұрын
What is the default settings of (P15) for a Zero 10X?
@M.Rosenburg5 жыл бұрын
Did you have this Settings ? Because My Controller Jas also wrong Settings
@oscargomezarango91843 жыл бұрын
P3 = 52/ P15 = 44 is approximately 28% of battery; the manual says the Voltage 42 =15% of battery approximately. For 52v 18 ah
@racismitsstopswithme74443 жыл бұрын
@@oscargomezarango9184 thanks heaps Oscar, i appreciate your help, and maybe you happened to know for 52v 23ah? cutoff voltage?
@TnTckoo5 жыл бұрын
Can i change cruise activation time ( p17 )? How?
@ericksonsasot21294 жыл бұрын
What is cruise activation means or for? p17) no idea at all. Thanks
@-Calmyoursoul3 жыл бұрын
i dont think so, default its about 4-5secs.
@oleg_36545 жыл бұрын
How do you fix the "Error 08" in the Controller?
@fuceye4 жыл бұрын
slow down or reduce charge current
@mange0132 жыл бұрын
i cant put on the lights the symbol shows but no light
@FalconpevSg2 жыл бұрын
Your dc converter light module is damaged maybe
@saltydegen4 жыл бұрын
Please help I brought my 10x from you guys So happy!! I had a full charge on the scooter and completed a 4 mile ride and then turned it off. I returned later the same day and turned the scooter on to find the battery Barr apparently was empty and was flashing with the red warning triangle next to it.. Thank you.
@saltydegen4 жыл бұрын
E 10
@FalconpevSg4 жыл бұрын
How is the Error coming along? Provide us an email for us to communicate better.
@gdkrycha5 жыл бұрын
What should be cutoff value for 52V battery?
@Cajunrich3 жыл бұрын
44v I think
@nicolasl4824 жыл бұрын
Mine didn’t shoe p2 menu , why ? , helpppp😪
@lambo795 жыл бұрын
How to enable cruise control while riding? Pull a level? Double pull?
@FalconpevSg5 жыл бұрын
Daniel Looi hold for 5 seconds maintaining the same speed
@lambo795 жыл бұрын
Falcon PEV thx will try it out
@kerwindapog5 жыл бұрын
What is the default motor magnet for zero 10X?
@xorbe25 жыл бұрын
28 is the setting
@ptescreen185 жыл бұрын
xorbe2 what about zero8x?
@ziedonispetrovs54804 жыл бұрын
Default is 30. Read the manual guys.. www.falconpev.com.sg/products/zero-10x?variant=12223484657731 Find the e manual pdf
@peterchoy528 Жыл бұрын
Nice thanks
@rjshhooba98573 жыл бұрын
So it has no blue tooth?
@rjshhooba98573 жыл бұрын
it has no android app?
@FalconpevSg3 жыл бұрын
Nope, you don’t want those as they are a huge hassle.
@norsco2724 жыл бұрын
Thank you, very helpful 😁
@serious-rc9334 жыл бұрын
Can i somehow reset the km?
@smator64224 жыл бұрын
do u found a solution yet?
@smator64224 жыл бұрын
i think he sad that p16 is gone reset it
@piccolociccioo2 жыл бұрын
P15 ? zero 11x battery 72v 32 ah
@Haunuva Жыл бұрын
Thank you!
@Blox1174 жыл бұрын
i get e10 on LCD what does it mean?
@FalconpevSg4 жыл бұрын
E10 is connection issue between lcd and controller