WEIGHT DISTRIBUTION HITCH - Why We DON'T Use One - RV Life

Our travel trailer towing setup does NOT require a weight distribution hitch. Check out this video to see why!
☆THE DYRT PRO CAMPSITE FINDING WEBSITE:
*UPDATE* The Dyrt is now offering a 30 day FREE trial to The Dyrt PRO instead of 10% off as shown in the video. Click the following link and use promo code Fate! thedyrt.com/pro...
☆HITCH INFORMATION:
Weight Distribution
www.etrailer.c...
auto.howstuffw...
Standard Ball Mount
www.curtmfg.co....
www.etrailer.c...
☆PATREON SPECIAL ACCESS:
/ fateunbound
☆FATE UNBOUND RECEIVES A SMALL COMMISSION WHEN YOU SHOP THROUGH THIS AMAZON LINK:
amzn.to/2UaGUZx
☆SOCIAL MEDIA:
Instagram: / fateunbound
Facebook: / fateunbound
Check out the rest of our videos: / fateunbound
☆SPECIAL THANKS to our Patrons who have pledged $5+ at / fateunbound to help make this video possible!
⭐ Allan & Karen K.
⭐ Allen H
⭐ Andy
⭐ Andy U.
⭐ Bill & Cathy O.
⭐ Bill C.
⭐ Bob K.
⭐ Bridgette & Ryon
⭐ Bryan A.
⭐ Caroley
⭐ Chad K.
⭐ Chris & Doreen W.
⭐ Colette K.
⭐ Crystal C.
⭐ Curt E.
⭐ Dalaina N.
⭐ David & Brenda H.
⭐ David C.
⭐ David D.
⭐ David E.
⭐ David R.
⭐ Donald W.
⭐ Doug S.
⭐ Elizabeth S.
⭐ Franklin G.
⭐ Gary & Diane H.
⭐ Greg L.
⭐ Jeb & Barb B.
⭐ Joe & Cheryl P.
⭐ John A.
⭐ John C.
⭐ John L.
⭐ John T. L.
⭐ Joseph H.
⭐ Kari S.
⭐ Kathie S.
⭐ Kathleen M.
⭐ Ken & Hariven C.
⭐ Kyle O.
⭐ Larry M.
⭐ Lisa H.
⭐ Lucinda M.
⭐ Lydia W.
⭐ Mark & Melinda A.
⭐ Matthew H.
⭐ Melissa M.
⭐ Michael S.
⭐ Mike O.
⭐ Nancy D.
⭐ Nathan & Stacey R.
⭐ Rachel B.
⭐ Rico G.
⭐ Rily C.
⭐ Robert C.
⭐ Ron & Susan H.
⭐ Ron B.
⭐ Ron B.
⭐ Schylar B.
⭐ Scott @ Go Small. Live Large!
⭐ Scott & Charlotte R.
⭐ Sigmund K.
⭐ Stephen C.
⭐ Steve C.
⭐ Steve H.
⭐ Susan R.
⭐ Vern & Kathy J.
In our three years as full time RVers I have been asked again and again why we don't use a weight distribution hitch. The simple answer is that our truck is over-rated to handle our particular travel trailer, we experience no sag at the rear of our truck, and we experience no trailer sway at highway speeds.
I've heard many RVers incorrectly state that every travel trailer towing setup requires a weight distribution hitch or sway control. I believe this is because RV dealers have been spreading misinformation regarding this topic to sell more weight distribution hitches and line their pockets.
So, to clear the air, in the video below we explain how a weight distribution hitch works, the reasons someone may need one, and why we do not use one.
*Affiliate Disclaimer: As an Amazon Associate I earn from qualifying purchases.

[@normblais7527]

I’ve been a mechanic for over 40 years now ,five of which were spent in a custom hitch shop, and I will say this you’re absolutely correct I often see people removing critical tongue weight with these devices.

[@FateUnbound]

Exactly. A lot of people seem to believe that WD hitches always improve your towing setup. But they only improve it if there's excessive rear sag resulting in too much tongue weight which also pulls the front of the truck up resulting in not enough weight on the front tires. Putting a WD hitch on a setup that doesn't need it forces the opposite problem which is equally as dangerous: not enough weight on the drive tires and too much weight up front. It's very simple to use a CAT scale to determine tongue weight and if it's over 15% of the weight of the trailer, you need a WD hitch. If you don't have enough weight distribution, it is called Under Distribution, and can cause loss of steering and braking control. If you have too much weight distribution, it is called Over Distribution, and can cause brake and axle fatigue and failure.

[@RoadieWingZZ]

You should ALWAYS use a WDH if you’re towing over 4000 lb and experience more than 2” of rear sag and 1” of front rise. Period. Proper adjustment is the key.

[@calebc6028]

Oh so they don’t have it setup correctly, if you follow the manual you won’t loose weight on the hitch rather the angle your towing at it keeps your truck in line with the trailer it doesn’t remove weight that is physically impossible, you just made that up

[@GregoryByerly-eg6vq]

@@FateUnboundwrong sag isn’t what it’s all about it’s a long empty box all trailers sway you could pull it with a tractor trailer and it won’t matter the rvs still sway

[@annej5699]

One factor I have not heard mentioned in your (or anyone else's) videos about towing and weight ratings is the actual hitch (not the ball or shank) rating itself. I climbed under my pickup to look at my hitch (the part permanently attached to my truck) and found it had two weight ratings, depending on whether or not weight distribution was being used: Without weight distribution a max of 5000 lb towing and max 500 tongue weight With weight distribution a max of 11000 lb towing and max 1100 tongue weight I realized that without weight distribution the trailer I am planning on buying can, once loaded, exceed the safe maximum rating for my actual hitch. Your truck is burlier than mine, so it likely has a stronger hitch than mine (you could climb under and look to verify). But I thought it worth mentioning this often-overlooked but important weight rating.

[@whatdoyouthinktodd]

He could but he won't cuz I could prove him wrong He's an engineer, can't teach one of them anything. Yep y'all brought to you by grammarless sounds stupid yeah not using a weight distribution hitch sounds stupid too.

[@jakemedley7423]

@@whatdoyouthinktodd hey don’t lump all of us engineers into that. I have towed since I was a kid and WDhitches and sway control are super nice and the only time you should undo is when you are off road or need the better maneuvering of now sway bars.

[@whatdoyouthinktodd]

@@jakemedley7423 well sir I am very sorry to lump you in with the group so there is at least one engineer that is not hard-headed You should be think by everyone that has to deal with a normal engineer and a daily basis Thank you for your service any engineering world and I'm not joking and I'm not bashing you one little bit truly thank you for being someone who actually can think and take others seriously. Sorry there's no grammar in this I'm speaking into my phone and I do not have the time to do so.

[@UncleSarkis]

The hitch receiver is what is usually bolted to your frame. The hitch goes INTO that receiver.

[@hoytoy100]

The ford towing guide is very clear in the limits with and without WD. An accident without the manufacturer guidance can lead to some liability.

[@jessicam.4148]

Also be sure to check your vehicles manufacture's towing guides, for example Ford recommends for the F-150 a weight distribution hitch, any time the tongue weight is over 500lbs

[@aliciabrowndocken4660]

We had a weight distribution hitch with our travel trailer and loved it. We had a front bed with 40 gallons of water storage underneath it (320 lbs) and a rear bathroom with two 40 gallon wastewater tanks (Grey & Black). Just imagine how much tongue weight "Change" we had between Going and Returning. I had 2 Completely different settings on the Spring Bars depending on whether that 320 lbs of water was on the Tongue or behind the rear axle. Then there were the two 30 lb. Propane tanks on the tongue. When I took 400 lbs off of the Tongue and Placed 320 lbs on the very back of the Trailer behind the Axle it was a Game Changer. I don't have any Issues with my current setup. 7,000 pounds of truck and a 650 pound flatbed trailer for 2 Dirt Bikes.

[@mattc3169]

Even with no sag or rear squatting of the tow vehicle you may still experience a porpoising effect while towing. For those that don’t know what that feels like, it’s like when you’re in a boat and you feel rocking front to back after going over a wave. It can definitely get you feeling a little motion sickness after a while. The weight distribution hitch helps tremendously with that effect.

[@davidcoulter7671]

This is the only reason that I use a WDH.

[@anthonyfragale9862]

@@davidcoulter7671 I’ve been using a wdh for 10 to 15 times since I went from a half ton F-150 to a Ram 3500 srw with a heavy “as in lbs Diesel engine block. “. I had some porpoising from concrete to bridge to concrete joints. But with all the proper settings of these items: 1. Height of trailer front 21.5” back 21.5”. 2. Height of truck front back before trailer weight and after to within 1/2 inch. Of previous measurements. As stated in directions. This last trip from Huntsville through Houston to Galveston TEXAS was like on a ocean.

[@anthonyfragale9862]

Like a small boat in the ocean. I removed wdh bars for return trip and was able to go over 70 mph over these uneven road transitions flawlessly. No sway at all either partly because of a 4door longbed 1 ton truck. If I were in windy conditions I would pull over and put them on for the friction of the ox round bar. No chain wdh. Safety chains of course.

[@dwighthapeman6590]

You used to have to hand crank cars to start them and in the 1960's air conditioning in cars was an expensive option. We have come a long way. My weight distribution hitch is wonderful for towing my 7,000#, 27' Lance with my Silverado 2500. Absolutely no sway on the highway. Solid and stable. I wanted to see just how the rig performed without the bars on the hitch, so I tried it. It was like night vs day. The hitch makes an amazing difference. The hitch was expertly installed by my dealer and dialed-in for my truck. My trailer and truck are perfectly level when towing with it. To each his own, but as for me, I'll go with the technology. BTW, I love your channel.

[@joej2353]

Totally agree. I don’t think every rig NEEDS one, but I think most all would BENEFIT from one.

[@westmountainadventures3606]

Our 30 ft, ‘07 Wildwood Sport LE , has a dry weight of 7480#. When we get our tow vehicle we will be putting a WDH on it as we will be over 8k# for sure. Maybe closer to 9k. D.

[@jdmixon80]

WD hitches are just bandaids. Get the proper sized tow vehicle.

[@Fudgieguys1969]

I am like you. I have a 2018 RAM 2500 (Gas) towing 2018 Keystone Outback 266RB, the dry weight is 6700 LBS. No, I probably don't need a weight distribution system, BUT! I have found out over time, there is a big difference and I have confirmed on CAT scales to prove my weight distribution system is almost perfectly set up on my truck. Even weight distribution over all axles. That is why I use a weight-distribution system. You do not want to be pulled over by DPS to check if you are legal on your axles. Now in town, I tow without the distribution, but again that is only in town going to and from the RV dealer for maintenance.

[@cyumadbrosummit3534]

Sounds expensive and cumbersome , no thanks.

[@ng1663]

I pull a small light 17 foot travel trailer. By using a weight distribution hitch with a relatively large truck, I am actually overloading the single axle of the trailer by forcing it to carry some of the weight of the larger truck.

[@herb7877]

You hit the nail on the head; "Do your own research" ! I am not disagreeing with your 4 points about needing a WD hitch but I'd also add; It doesn't hurt to take the extra measures for unforeseen circumstances that can avoid trouble. Although I may not "require" a WD hitch I use one and air bags. I feel a lot more at ease with my towing experience. I have ~40+ years of experience and have had blowouts, bearings burnout, sudden stops and high cross winds, snow .... It's just inexpensive assurance & insurance for me.

[@hughtruex]

Another issue is litigation in the event there is an accident. A lawyer might pick you apart. I have an F350 4x4 and my trailer is is also 24'. I use a ProPride. I am sure I could tow without weight distribution but want the piece of mind.

[@RV_with_Noni_and_Beard]

Combining a WDH and air bags is usually a terrible idea. The air bags end up cancelling out the weight dustribution.

[@herb7877]

@@RV_with_Noni_and_Beard I do not believe so. The air bags reduce the 'porpoising' when crossing wavy roads and large bumps. The WDH is transferring weight to the front end of the truck and axles of the trailer. I'm taking little to no additional weight off the coupler with the bags, the WDH is doing that . Made a good improvement in making the leverage point a lot more firm. I am NOT using them in lieu of the WDH as some people are attempting. They DO NOT replace a WDH.

[@RV_with_Noni_and_Beard]

@@herb7877 go to a scale and measure. Just do it.

[@herb7877]

@@RV_with_Noni_and_Beard Just as an FYI ... I did go to a State scales this weekend. Weighed each axle (both truck and trailer) with WDH & without. Airbags inflated to 35#'s. Weight is being transferred as it should be. You'd be defying the principals of physics if it didn't. The Nov. 2020 issue of "TrailerLife" page 34 has an article on it as well.

[@scottsammons795]

You are right. We had a 2000 version of your truck Duramax, 2500HD Crew cab Short bed. We towed a 25BH without any issues at all. We now pull a 21QB about like yours with a Mercedes ML400. No ifs ands or buts, It needs a load leveler. I tried it without and it was a handful. Now, even in wind my Curt makes it drive as though it was on rails. As you said, different rigs, different requirements.

[@robertcoleman4696]

I’ve been driving a big rig for twenty two years. You have just been lucky so far. High winds have blown big trucks right off the road. Hopefully you’ll never have to say, I really wish we would have gotten a sway bar setup.

[@jonathonhigham2793]

A 5th reason to use a WD hitch, My owners manual states any trailer over 5,000 lbs requires a WD hitch or warranty is void.

[@bradbain1099]

Wouldn't you leave the trailer at home when taking the truck to the dealer for repair?

[@magnapilot]

So if he's out of town and needs to stop by a dealer for a emergency warranty repair, he's just supposed to drop the trailer at a random parking lot?

[@ColeTowsley]

@@bradbain1099 It would also be problematic if you get into an accident, even if the accident isnt necessarily the result of the trailer configuration. If you're not adhering to manufacturers specifications, your insurance company may not be required to cover you.

[@bradbain1099]

@@ColeTowsley If your insurance doesn't pay when you screw up, what's the point of having insurance? You realize every day they pay for damages caused by reckless driving, speeding, running red lights, driving drunk, and 100s of other questionable actions. Why would exceeding towing recommendations be any different?

[@ColeTowsley]

@@bradbain1099 operating outside a specific legal area and exceeding manufacturers recommended operating limitations are entirely different, and in many cases participating in illegal activity resulting in an accident WILL void your coverage. Depending on your policy restrictions, you might be surprised what your insurance company will fail to cover.

[@lessard2020]

I feel much safer with my weight distribution hitch on my 6500 lbs dry trailer, it takes 5 more minutes hooking up, but I feel safer and it handles better, my two cents! Most manufacturers suggest it because you probably need it. From a Ford Towing Guide : CLASS IV EXTRA-HEAVY-DUTY • Over 5,000-lbs. gross trailer weight • Most applications require a conventional weight-distributing Cheers

[@shawnchong]

A weight-distribution hitch is definitely safer! Most people who wear seatbelts never need them, right? But that one time it saves your life...

[@jbouvet]

Glad you’re saving a couple hundred dollars and minute amount time to post this information. I had to reply here because I absolutely agree with these responses. You don’t need it until you need it. Why is it so difficult to use a a safe hitch? Do you stay well below highway speeds? Do you exceed the speed limit? I’ve driven trailers, RV’s, and trucks for over 30 years. They all sway and at higher speeds its more dangerous. Yes, do your research and don’t believe this video. Mitigate risk, wear a helmet, click your seatbelt, and use a safe hitch. The costs are negligible to the benefits.

[@VOOODOOO37]

agree totally..

[@CandyMan69007]

Ty for the information now I know what to look for on a f-150 . Waiting for the 2024 to come out

[@bradleyliebl2931]

You also need to watch state laws, as the tongue weight in some states will determine if one is needed or not.

[@jam471975]

I agree that you can get away with pulling that size of a trailer with a 3/4 ton truck without a WD hitch. But I have a feeling they have not tried a WD hitch to see the difference it makes even with that truck and trailer combo. There are weight distribution hitches out there, like the Andersen WD/Anti-Sway hitch, that does not reduce the turning radius at all and that hitch is super easy to hook up. I had a 2020 Wolf Pup 16FQ TT which weight about 3500 lb with my gear in it and I thought I could get away with not using the WD hitch behind my 2019 Silverado which has a 7200 lb GVWR.... but after a couple unpleasant experiences pulling that TT in moderate wind I quickly realize that I wanted a WD hitch. WD hitches just makes such a big difference and towing much less stressful.

[@lawrencewiddis2447]

My Silverado rating from Chevrolet states I don’t need a WDH for my 5000-5500 pound travel trailer fully loaded and I’ve stopped using one. Detect NO difference.

[@zero_cool817]

I have a 2005 2500 HD Duramax, my travel trailer weighs 6k lbs. I pulled my TT one time without a weight distribution hitch and it didn’t seem too bad. But Using the weight distribution hitch made a huge difference I will always use it. I was blown away with how big of a difference it was.

[@yeahthatshouldwork]

I have similar setup as you. I have pulled with and without WDH on my 7K trailer. Having the bars on certainly makes a difference. Pulling without is certainly doable.

[@azxp]

I worked with Torklift on my setup. I have 6.0L GMC ext short bed with a 1/2ton camper I haul, and I tow a flatbed trailer with a Jeep and camping gear on it. Torklift also said with my setup I did not need a weight distribution hitch. They also said that if i was going to have a weight distribution hitch I would need a different one depending on the load on my flat bed trailer. They also said that most people buy the wrong distribution hitch anyway. There is a science to it and only works if you are towing the same load every time. I have multiple different trailers. They said with the class 5 hitch and extension and the truck I have it is more than enough to haul my trailer safely. I have since put on 10K miles travelling all through Utah up and down the Rockies with no issues whatsoever. Like you I have no sag, and I do have compensating air bags. Thanks for putting yourself out there beyond popular belief.

[@chaosncheckt9356]

Pulling an 18' teardrop with a Jeep Grand Cherokee. Factory tow package on the jeep, the only thing we added was a sway bar. Since our Jeep's tow package came from the factory, our vehicle once the ignition is on, will level (use of air bags in the rear suspension), giving us a nice level ride. We have been told by many that our 18' weighing 3100 doesn't require a sway bar, but for us it's a peace of mind. Of course we have electronic trailer brake setup as well and have never had an issue and we've pulled ours for almost 20k miles. Good video, very informative.

[@Synergy7Studios]

weight distribution systems can handle tight turns, you just have to ditch the swap control bars once you get to the camp site. Then it behaves just like a regular ball hitch setup.

[@johnhines3591]

First, Read tow vehicle owners manual. It tells you exactly at what point you need a WD hitch !! You should always have some kind of sway control..

[@williambranham6249]

Interesting and informative. I have owned two used RV/truck combos: an Airstream / Suburban. and Casita/F150. I asked each owner to sell me the truck that had been used to pull each RV . I made it clear I didn't want the trailer without the truck. They reluctantly agreed. I went this route because I was flying blind. I knew nothing about hitches, etc. It worked out for me., never had a problem. Not a bad way to go if you have no experience. All this info is engineering science. David, you and Roe are the best. Being from Indiana doesn't hurt either.

[@likeachamp91]

I would still recommend a gen y boss hitch or shocker hitch. You spend this much time towing you’ll appreciate a smoother ride

[@grantdavis5992]

Not only does your truck have a long wheelbase, your diesel engine puts more weight on your front axle.

[@charger7022]

i think you missed one key thing that alot of people over look. some class 3 hitches may be rated at 10000 lbs but that is only while using weight distribution. it may only be 5000lbs without weight distribution. just cause the truck can pull it don't mean the 6 bolts holding the hitch on will.

[@Weak_juan]

GOod information. Take the rig to a cat scale and verify your axle weight, then you'll know 100%.

[@RVFishingAdventures]

Just watched this today and this is excellent information! Most people who have WDH systems are also running too much pressure on the weight system too. Many people follow instructions from the manufacturer for general use but don't really tune their setup for their rig. We had an 31ft, 10300lb Airstream we towed with a Chevy 1500 that was more than rated for that weight (on both GCWR and Payload). It had some sag, and so we used a WDH to level but I only adjusted it to remove just enough of the sag to make it work properly and no more. This is critical because WDH's can overload a trailer frame and cause it to bend or crack. One other note is that people often refer to hearsay "rules" when it comes to loading a hitch on a trailer. There is a misconception that the weight on a trailer tongue should be at least 10% or more of the trailer's weight. When in fact, the trailer manufacturer sets the hitch weight amount as a "rating". Meaning this is what your hitch weight should be, not more, not less. This concept goes completely against what many people think and why they tend to overload their trucks because they load their trailer excessively forward causing too much weight on the tongue which causes them to use a WDH when they actually didn't need one. Why? Because they should have loaded their trailer to match tongue weight *RATING*, and not followed the myth of weighting their trailer excessively forward. This is especially important with exceptionally light trailers which take large payloads like toy haulers. A toy hauler is designed to have a large load in the garage. This load ***removes weight*** from the tongue if properly loaded. Until there is a proper load in the "garage" there could possibly be too much weight on the tongue especially with the kitchen and bedroom forward of the axles. As an example of how wrong people think about tongue weights, there is a very popular KZbinr who goes to dealer lots on a regular basis to review RVs. In one of his reviews he went around reading the tongue weight **Rating** on a trailer and the got a trailer tongue scale and weighed the actual weight of the tongue of the empty trailer. He then made the extrapolation that some tongue weights are higher and that you should plan on your tongue weight to be higher than the stated rating. Again, the mistake he made is that it's NOT AN ACTUAL WEIGHT. It's an actual RATING. This means if a trailer weighs heavy on the tongue when empty then it's expected, based on where the cargo is, that once you load the trailer that the tongue weight will become lighter as is the case with a toy hauler. The reason this myth has formed: We don't weigh our trailer tongues loaded (or properly!). Therefore we have no idea how to balance our trailers. So we have excessive sag because we have overloaded the tongue and then we add a WDH to put a band-aid on the real problem: Improper trailer balancing. The basic principle of loading a trailer is this: A trailer is loaded properly when loaded at the maximum weight rating of the trailer yet the actual tongue weight is loaded no more than the weight rating listed for that tongue. Left, right, front, to back, the trailer should be loaded correctly to the appropriate weight ratings. Any unequal loading will cause trailer sway. Truckers know this. Movers know this. RVers are insanely dumb in this area and we need to get this one right. Fixing this one misconception could help an awful lot of people eliminate their WDH and have a better and safer towing experience overall.

[@RVFishingAdventures]

One easy way to weigh a tongue weight is to go to a CAT scale and unhook the trailer from the truck (chock it!) and have the tongue on one scale and the wheels on another scale. The tongue jack does throw off the weight slightly vs weight sitting on the ball, but this is enough to know how close you are. If your trailer is excessively over the tongue rating, the trailer is overloaded to the front and will tend to sway or worse, will attempt to jack-knife in an emergency even with a WDH installed.

[@ScottReedKC]

You don't need one until you need one, then it's too late.

[@brandonkoff]

You're not going to be able to tell this guy anything. He's a pro and knows everything about it because he's been pulling a travel trailer for 3 years. I've got a 3/4 ton pickup as well and it could easily handle my travel trailer but I'm not an idiot so I use a weight distribution hitch. And I guarantee That's a straight fucking lie that he's never experienced trailer sway even in high winds. I also want to know what the reason is he needs to blur out his license plate. Does he think somebody's going to get his personal information because they see his license plate on a KZbin video?

[@danielzatkovich4659]

@@brandonkoff Grow up.

[@gilianrampart8514]

@@brandonkoff I agree! Never experienced sway? Bullshit!

[@gilianrampart8514]

@@danielzatkovich4659 Get rational!

[@blueschild61]

This guy is an idiot. He has super powerful portable speakers (like nightclub speakers) that he takes out in to the woods to scare animals with. That, right there, tells you everything you need to know about his decision making skills.

[@kpd3308]

Ball mount drop/rise does not affect vehicle sag. It only affects whether or not the trailer is level. Also it helps weight distribution if the ball on your truck is as near the bumper as is practical.

[@larrynone6354]

I can tell you that what one you have makes a difference. I changed mine out to a different one, and what a different I have better control going into turns my brakes and more control it almost feels like my truck and trailer are all one unit.

[@stanburk7392]

easy way to do this. go to a scale get your axle weights with the trailer and without. just because your truck is sitting level does not mean you have not shifted axle weight off the steering axle. a common misconception is with air bags they make the tow vehicle sit level yes, but actually transfer weight off the steering axles. was something I have argued against but the video proved me wrong. Fastway trailer does an excellent video with actual scales to prove this. the video is entitled the difference between using weight distribution and air bags to level your load. I like their video it shows the whole process they use so its not just hearsay. this obviously does not apply to 5th wheels since their load sits directly on the axle.

[@JavierPadron]

Yes you can pull it and safely get down the road. There are benefits to ride quality and sway on a really windy day. I run with one because I like the way it rides hooked up smooth as butter. But they are expensive for the good ones like equalizer hitch. Judge your application know your weight and make a good choice if needed, and yes spend the money if needed. Btw: I run a 2015 2500hd leveled suspension with 7300 pound 32 foot trailer. Thus why I use one aswell to help keep my front end planted after a leveling kit.

[@DG-ss1gc]

You have a relatively small trailer . I have one , but the thing is a beast to put the bars on.

[@Yellowstonetim]

I am with you 100%!! I always use a sway control bar, but not a weight distribution hitch. Our trailer is small and the tow vehicle has adequate suspension to tow level and proper. No need for the extra work at all. I tow a 2017 Coachmen Clipper 17FQ with a 2015 Ford Explorer Sport with tow package. Tows level and solid.

[@pgrant7688]

I have a Ram 2500 w/a Cummins TD, & a 6500 # trailer for 5 years. I had to tow it to the dealer & I only had a ball hitch. I towed it 35 miles on a major US interstate and it was fine. No sway, no dip. Every other time, I used a WD hitch. Why? Because there were no problems at all, and I’ve towed the trailer across the country multiple times. I’d rather have that security even though I might not need it. This is a great channel, I enjoy listening to your insights.

[@connorplassins8693]

Do you NEED one? No. Does GM (Chevy & GMC) require a weight distribution hitch system for any trailer over 5,000 lbs? Yes. Can you? Yes. Should you? No.

[@agentorange2554]

Also-2015 Chevy Silverado toungue weight limit is 500 lbs w/o, 1200 lbs with a WDH. I'm looking at it right in the owners manual. Ignore these limits and get in an accident, your insurance is worthless.

[@salamancadingding]

It really just depends on your vehicle and trailer combination at the end of the day. If I have a 3/4 ton truck pulling a 16' wolf pup, I'm probably ok without a weight distribution hitch. If I have a 1/2 ton truck pulling a 32' Jayco, then I'll more than likely require one!

[@dewrus2153]

Love your videos...thanks for all the great content. Since you actually asked us to do so, I do have to clarify a few things. 1. You said a WD setup can limit turning radius but I have to point out that is only with old-school chain/bar setups. Most WD hitches today use slide bars. I have a Fastway E2 and it does not limit turns at all. 2. You mentioned your truck experiences no sag at all with your given tongue weight. By looking at the side view in your video, I can clearly see sag. It's not a lot but it's there. I guess the question is what is the difference when your trailer weight is not on your ball and when it is? I'm sure it drops at least a few inches since most trucks are raked from the factory. Along the same lines, there are those who experience sag and correct it solely with airbags instead of a WD hitch thinking that since it's level that they're safe. It's good to be level but "level" doesn't equal "safe". Science shows that when you correct "level" using only airbags, you can actually take even more weight off the front axle making it even more prone to sway, and loss of braking and steering control. 3. The real test would be to weigh the front of your vehicle (one or both front tires) without your trailer and then with it. If you experience little or no weight reduction, then a WD hitch won't be advantageous. If you see weight reduction on the front tires, then a WD setup would help even if your truck appears level. 4. You mentioned WD hitches take longer to connect. Ours might add 1 minute to the time to connect. So, you're correct but the time required is very negligible. 5. You are correct in that you probably don't need one for your setup but you should also note that it still has benefits that are valuable even if you can get by without it. For instance, I wear my seatbelt every day even though I've never been in a serious car crash. So the logic that I don't need to wear one because I've been driving for 35 years and never really felt a need for it isn't logical...just like the unforeseen future emergency you might have to make one day when the difference between a close call and a terrible accident is a $300 WD hitch. I guess what I'm saying is that just because you can get by without one doesn't mean it wouldn't be better and safer with one. We all care about you guys very much and always want to see you being as safe as possible. 6. Okay, I just want to finish by reiterating I love your videos. Even though I've been camping for many years, I always enjoy seeing what others are doing and am always learning from others experiences. I've learned a great deal from your experiences and insight since you've had your channel. Please stay safe and keep the great content coming. Have a great day!

[@kathleenvitello6233]

We just got the Andersen WD hitch system. Will we have limited turning? What would happen if I try to do a 90 degree turn? I'm having trouble finding the answers... Thanks in advance.

[@xxRock81xx]

@@kathleenvitello6233 the design of that setup has no turning limits.

[@gregorypecaut7164]

The trailer will hit the truck before you even get to 90°.

[@gregorypecaut7164]

Remember, WD is for going down the road. Remove It before backing into tight spaces. If you want tight maneuvering, consider a fifth wheel.

[@renner8668]

was going to leave a post but you said it already. i have been towing for over 25 years and there is definitely a added benefit to using weight distribution even on light loads where you don't really need it but it just makes the towing experience that much better. I have not invested in the new TruTrack style that is a combination of distribution and sway control, I use the Curt round bar 15k setup an all my trailers and have no issue with tight turns at all and since i know my setup it literally only ads a few seconds to hook it up. This setup i prefer over the oldest trunnion style just because i find it to be smoother and less noise but any type is definitely worth the investment specially if your towing all the time. Another good addition is air bags if needed to level a load out and to help minimize bounce. 2 things i always have when towing to make my experience the best that it can be. Just like my firearms, better to have it and not need it, then to need it and not have it.

[@Ben-sj4pu]

I weighed my rig with and without using truck stop scale. It measures individual axles. That helped me make my decision.

[@Spridle60]

I don't use weight distribution. I do use a friction sway bar.

[@billbarrett6196]

Never go against the manufacturer's recommendations. And, most (not all) will recommend using a weight-distribution hitch when towing over 5000 lbs. Even the eTrailers link hints at this. But, check with your owner's manual to find out what your limits are.

[@kjellmagnestubhaug2839]

So agree 😎 and the only thing that can make your ride better is with a Shocker hitch 👌😎

[@roberto.peterson9917]

Weight distribution set ups could possibly bend trailer Frame when going thru construction zones or off road towing depending in trailer manufacturer frame used to build the trailer lighter frames have tendency fail when distribution hitch is used

[@davidbarbour9929]

Thank you, finally someone said it. I have a 2018 Ram srw 3500 Cummins, I pull a 7k travel trailer with 700 lbs tongue weight. I don't run my wd hitch, I don't need anymore weight on the front axle with that diesel, and 700 lbs on hitch just makes it ride better, even levels it out a bit. I've never had sway problems even on windy overpasses. Just my experience.

[@joej2353]

I agree that not every travel trailer/truck combo needs a weight distribution hitch, but I think that most all would benefit from one. That said... love you guys. Always great info. Keep on truckin!

[@ebolawarrior451]

If it doesn't fold your frame.

[@skydouglas996]

Question: let’s say you agree with this guy and don’t use a WDH and the SHTF from wind or whatever and you crash…are there any legal liabilities for not using a WDH or will you have problems with the insurance coverage? My truck will handle twice my trailer but I use one to be safe and not have the added stress of those questions.

[@edrodrigues3333]

Maybe I missed it, but he didn’t talk much about tongue weight or what the receiver hitch on the truck is rated for. The rating on the receiver is different when using the a equaliser option, almost doubles it.

[@bladedspokes]

A civil jury would be easily convinced that not using a WDH was negligent.

[@monster-pq7ln]

But he has a Bachelor's Degree and stuff.

[@philc.9280]

We pull an ultralight TT less than 2500 lbs with a half-ton Nissan Frontier and never had used a weight distribution hitch. I've never driven in high side winds yet but it seems to glide on the freeways. Those things weigh a lot and we are trying to minimize as much as possible

[@rangerguy196]

WDH's take all of about 5 minutes to put on. I cant speak to every situation, but I've used WDH's on a long bed F350 and a 6.5' F150 and I've never had issues with turning radius.

[@coastsider7645]

really good advice, one must make one's own decisions, ty David

[@dirtrider88]

actually sometimes the law makes your decision

[@brianhightower971]

I use an Anderson distribution on my small single axle trailer - more for bounce. Also, no grease.

[@FateUnbound]

This is one thing I failed to mention in the video, that a WD hitch will tie the truck and trailer together and greatly reduce bounce at the hitch point. Excellent point Brian 👍 -David

[@TomLentz]

@@FateUnbound I agree with your reasoning for not needing one, but if you ever change your mind (like if you get that 4WD truck you want) I also recommend the Anderson for a trailer your size. They work pretty well. Not the best for amount of weight transferred but good enough for smaller trailers, no bounce, light, simple, quiet, clean, quick and easy on/off, can back up, good sway control...

[@khoatran9482]

I'm with Brian, everything you hate about WDH's in your video other than cost is negated by the Anderson. I absolutely love my Anderson WDH. Easy on and off (if I even take it off). Can back up with it take TIGHT turns. And weights so little (less than 15lbs).

[@rclewen]

We also have a single axle trailer (4500 lbs GVWR) and tow with an F250 (10,000 lbs GVWR). It tows well, but I do notice more bounce, so I am considering adding the Andersen WDH to help with bounce.

[@jamesglenn520]

If you are experiencing Bounce it could be as simple as Shocks. You should run a little stiffer shock on your truck for towing. And check the condition of the shocks on your trailer if it is equipped with them. Towing will shorten your shock life on your truck faster than most people realize 👍

[@pineychristian]

You speak of trailer sway when towing with dual axle trailer. Single axle trailer dont track as good and tend to have trailer sway much easier

[@thegoodbible8270]

Thanks for the app, getting it now.

[@ronaldpigeon4713]

We did not use wd hitches years ago, trailers were smaller, folks had experience driving different conditions, idiots did not cut you off, and we did not drive so fast. Overloading and driving fast probably cause most accidents.

[@kerischneider1476]

I use a f350 desil no distribution hitch also my truck is normal Hight and my trailor the axle is not flip and no lift it rides great

[@brianbeach2071]

Great insight, I appreciate all of the information you provide. I'll point out that the tongue weight, as a percent of the trailer weight has a huge impact on stability. Most travel trailers are designed so that at least 10% is on the tongue. Don't do anything that would make the tongue weight less than 10%. I towed boats, as part of my job for a number of years. Basically, the more tongue weight you have, the more stable the rig will be in terms of sway. Sway control is not a substitute for adequate tongue weight. I think you provided good guidance as to when an equalizing hitch is needed.

[@richardnead4840]

Good info, as a former transporter for many camper manufacturers the rule of thumb was if your camper is 30' or longer we had to use our distribution hitch.

[@yzhang8629]

I think the getaway is, when the combination of truck cargo and trailer doesn’t exceed GCWR and GVWR, if there is a significant sag, use WD; if you experience sway, use sway control.

[@guloguloguy]

....IMHO: It's better to have it, and not need it, than to need it, and not have it!!.... What about the actual receiver bracket?! What is need to support a "weight distribution hitch"?!....

[@brianfreeman5257]

I agree in your case. Your truck can easily handle that trailer. I was pushing my half ton suv with 6500lb trailer. The weight distribution hitch was essential. Bottom line: know your numbers.

[@FateUnbound]

This right here. Some setups need a WDH, some don't.

[@joe1071]

@@FateUnbound weight distribution, no. Sway control, yes. After my 1/2 died our travel trailer, we upgraded to a 3/4 ton truck. I had a good conversation with the tow truck operator, and he pulls travel trailers as well. He said he would always use sway control even with a 3/4 ton truck no matter what for safety. Said he tows trucks and trailers everyday with axle failure or other significant issues, and when you experience an issue like this you will 200% want sway control, or else you have no control even with 3/4 ton. It’s not for the regular tow days, it’s for when things don’t go as planned 👍

[@dhrandy]

Your max tongue weight is 800 lbs with that truck and your trailer is between 500-800 lbs, maybe more if you load it down. The right weight distribution hitch will allow a higher tongue weight.

[@shoresguy48080]

One thing missed Is tires I have found is the higher the load rating on the LT tires the less sway you have. I have a F150 it had stock tires which were designed more for fuel economy I Switched to a heavy duty Light Truck tire the difference was huge

[@carjack69]

David G very interesting point about those tire...what brand is these for f-150?

[@dewrus2153]

Good point David. I am the same. I had the stock Goodyears on my F-150 and it rode nice but felt like I was riding on marshmallows once I hitched-up. I switched to BFG KO2's with a load range E...difference is like night and day!

[@mrnotnomis]

Our WD hitch takes about 5-6 minutes to connect, and the sway control has to be disconnected when we back up. So, yep, inconvenient! But my MAIN worry is that WD hitches put a LOT more strain on the tongue of the trailer. I have seen a several people (and lots of comments) on videos where the tongue has bent during a trip, especially after hitting a bump. I can't really go without a WD hitch though. We have a Chev 2500 Duramax short bed and a 33 ft 9k lb trailer. Wheelies in that rig don't sound fun to me. I have towed without a WD hitch. The trailer was a 29ft camper with an unknown weight similar to what I have today. I had a F350 CC long bed 4x4. The front axle felt light and had more bounce than I was used to, but I had no issues towing about 400 miles over the worst highways that LA, MS, AL, and FL have to offer. Great video! Thanks for sharing and providing perspective from both sides.

[@franksmythe6969]

You should connect your trailer to your tow vehicle, then see how many inches off level your trailer is. At that point you can choose the appropriate ball mount.

[@johnnyebelindabewley4536]

1. Have your vehicle inspected for all towing weights. 2. Have your towing gear in your vehicle repaired. 3. Get the tow wires brakes on your vehicle repaired. 4. Remember to check the weight of your hitch and ball are part of the weight of the tow tongue weight. 5. Subtract that weight from the load of the rest and you have remaining weight distribution needed if that.

[@groofromtheup5719]

I picked up a large enclosed car hauler/multi-use trailer. I towed it with 2 vehicle. primarily a 1/2 ton Chevy Avalanche. secondarily a 1 ton SRW standard cab F350 V10. They were both about the same WB. The trailer was rated for 10k gross and was like 4400 empty. Without a WT hitch, the 1/2 ton was scary even with the trailer empty. The 1 ton was OK empty, but didn't feel as good as the 1/2 ton with a WD hitch. Loaded (I used it to move, so a few trips), both NEEDED the WD hitch. My goal with the WD hitch was to bring the front ride height of the vehicle back the it's unloaded height.

[@itinerantrebel1799]

The reasons we don’t use a WD hitch are that it reduces weight on the back of the truck and the more weight, the smoother the ride, also part of the reason for going from 20 lb to 30 lb propane tanks. Also, the WD hitches make noise that is annoying. We tow an 8,200 lb, 30 ft travel trailer with a Ford f450 and we do use a friction sway bar because in strong cross winds that is needed. We boondock a lot and put generators, fuel and other equipment and toys in the bed of the truck. It really smooths the ride out compared to when not towing. Also, towing with the fresh water tank full also helps and is needed for boondocking. Even with all that going on the rig stays level. Between the tongue weight and the cargo in the truck bed and the family in the cab we’re able to get the weight in the truck up to half of its payload capacity and that makes a difference in ride quality. The sway bar is a necessity though in high winds traveling across the Great Plains.

[@magnapilot]

If you aren't worried about manufacturer's warranty liability, insurance liability, and many state's towing laws, sure, go ahead and tow without one. It's not so much on "if" your truck can tow with it or not, it's more on if in the event of an accident (and subsequent insurance claim) , or a bored state DOT police officer, are you willing to be without it? Are you willing to be sued for gross negligence in the event of an accident for not following manufacturer's specific weight ratings for the hitch?

[@AztecWarrior69_69]

If you think that 2:25 is level then you are either lying to yourself , being disingenuous or you need glasses.

[@tomperley8399]

It’s all about tongue weight. A weight distribution hitch can be used with or without sway control, it is, as you mentioned, designed to distribute your hitch load across all axles. You missed two items, what is the rating of the receiver hitch, they are often rated with and without a distribution hitch (usually 1000/10,000 or 1200/12,000), and what is the capacity of the drop hitch? That capacity is different than the rating of the hitch ball. Your trailer is 5400lbs loaded, your hitch weight should be around 10% or around 540lbs which is well under the 1000lb capacity that your receiver should be rated for without a distribution hitch, so you definitely are safe and don’t require one. Everything else you included is great info, this is just more food for thought. Love your videos, keep up the great work. Also, I am sorry for your loss, and hope that you able to enjoy this time with your family. Stay safe!!

[@runningscout14]

His truck if he has the factory hitch on it is only rated for 500lbs and going off the empty weights for his trailer the tongue weight is 515lbs.

[@AmericanSurvival001]

I found that people that drive Ford F1 50s which are light in the pants I don’t inherently have adequate anti-sway bars use weight distribution hitchs and some Chevy owners as well but in general I’ve driven several model Dodgers and I even have a Durango which is half ton capable(older model) and I don’t use A wait distribution hitch either and it drives fine with 33 feet of trailer behind it.

[@benjaminapeterson]

WDH and Sway Control are often packaged together but are not the same thing. You can use one without the other.

[@BeefNEggs057]

The new ones are integral. The bars that distribute weight also provide the resistance to sway. You couldn’t separate the features.

[@waltergrasmick5615]

Not all are integral, a lot of newer ones are however and would not require sway also. In situations where WD is not required, you can still get sway control that can be beneficial.

[@kenhuth1762]

Thanks David, the sticker on my one ton ford van states a weight distribution hitch is required for trailers over 5,000 pounds. While I’m sure I don’t need it, that might come into play in an accident while towing. Insurance companies will try to get out of paying a claim if they can. Worst yet being on a witness stand and offering that even though your vehicle and trailer specs require a WDH you determined that you didn’t need it. Not going to fly with a jury. Please follow all OEM requirements or risk financial liability.

[@drylakesranch9880]

He said do your own research to determine what you need. His truck doesnt have that same manufacturer requirement as yours. So your point is moot. He said not everyone needs WD, based on truck and trailer, etc. You are claiming he still does need one because your truck does, and implying that he is wrong and irresponsible. You need one, he doesn't.

[@kenhuth1762]

@@drylakesranch9880 the last sentence says to please follow all manufacturer’s requirements is hardly a moot point

[@deadswarmaking1135]

You are giving bad advice, you've been lucky because your trailer is right at that limit of being required to use a weight distribution hitch. You are just barely over your 50% GVWR and most manufacturers require the use of a weight distribution hitch over 5000lbs to achieve max towing ratings. Again you're right at that limit.

[@kenneyruggles4394]

He said not to take his advice. Use your best judgment. This was just something that worked for him

[@MrAlittle5150]

I am pickup my camper this weekend and I am new at this. I think I have a close tow setup you have (my camper is shorter). My camper is a Keystone Springdale 1750RD and I have a 2005 Chevy 2500HD. I don't think I need a distribution hitch, but I've had people tell me I do. But watching your video I think I'm going to try it with out.

[@DanBlackRacing]

Oddly my 2024 Keystone Rv Springdale single axle 20' TT at 3000 Lbs give me near sag (bring the truck down to level) on my 2021 6'-4" box V6 Warlock with the OEM 1" lift and HD rear springs. We got a 49911 WD hitch to bring it up a small amount to support heavier load outs when boondocking. What is even more odd is my max total weight is close with the truck being 5200 and the TT at 3300 loaded.

[@Denali_Rebel]

You’re the first person that says you don’t need a WDH for every trailer in all circumstances. I read about people with 2021 3500 Sierras towing a 5,000 pound trailer that insist on WDH. Doesn’t make sense to me

[@jeremymcmichael7371]

That trailer can't have that much hitchweight.

[@williamhudson4938]

The one thing you didn't address was tongue weight and loading your travel trailer to adjust same. If you load all your canned goods and other heavy crap forward of the trailer axle center, you're exacerbating the problem of balancing the entire rig. You really should have at least touched on this subject. Otherwise, good video.

[@Joseph-C]

Too light of tongue weight causes extreme trailer wag

[@doubled8247]

Best deciding factor is put the truck on a scale, empty and with trailer. Looking level has nothing to do with it. Airbags can make you look level while overloading rear axle.

[@Mayfairkid2]

How do you deal with trailer bouce? Without the weight distribution hitch, we experience bounce over bumps, even though the truck and trailer are level

[@jamesglenn520]

I would make sure that your Shocks on your Truck and Trailer are in good condition. If you are running Stock Shocks on your truck you might need a little stiffer shock. Just something to check first 👍

[@allens7476]

Not all WD hitches have sway control. Sway control requires friction, so hitches like the Equalizer have it built in. Otherwise you need to add a sway controller. I'm always surprised to see WD hitches only on RV's, never on horse trailers, motorcycle trailers, flat beds with bulldozers, boat trailers, etc.

[@orygunguns8521]

I use a WD hitch on my flatbed and horse trailer. Why? Because I only had a ram 1500 when I bought them and the factory hitch is rated at 5,000/500 (trailer weight/tongue weight) weight carrying but rated at 10,000/1,000 weight distributing. My trailers regularly weigh around 7,500 pounds. I don't use it on my f250 with class 5 hitch though. I'm probably the only guy that actually pays attention to the weight limits. Most people just go buy a stinger and ball from Walmart rated at 5,000# and hitch up a 7,500 pound trailer. Seriously. I've seen idiots hauling mini excavators on a 5,000# rated Walmart hitch.

[@duaneroepke8840]

I agree each to their own. I personally use torsion bars with out sway control when pulling heavy trailers. They make the truck and trailer ride as one unit. Don't have much bucking when going over(example) bridge joints. If the example you gave of the truck still saging with torsion bars, means that they didn't know how to properly adjust them or they had entirely too much for the bars or the truck. A side note...you can transfer too much weight off the rear axle also by NOT having correct torsion bar adjustment. Another part of the equation is proper trailer load weight distribution, very important for maintaining control and ride. Another part that is overlooked is tongue weight, not just gross trailer weight. Even the tongue of the trailer has the max weight stamped on it. Don't just go by your weight rating of the ball, but also the hitch shank weight rating (what the ball is mounted on). Some are hollow square tubes and others are solid with different weight ratings. Good material. Keep the vids comming

[@imxploring]

Excellent points.... the weight of the trailer is one issue.... how that weight is distributed in the trailer is another. Shifting weight rearward to lower tongue weight is a big negative and will result in loss of control and major sway issues.

[@larryprimmerjr8099]

I am in the same camp. I have a 3500 Silverado Duramax long bed/crew cab, I tow a 6.5k lbs 28 foot camper. Obviously my truck can pull this camper without a WD setup, but I find it helps with the 'bucking' or whatever you wish to call it. IMO this causes a lot of torque on the camper frame as well as causing all the items inside the camper to move about more. I think there is more to the story than do you need one or not based solely on truck/camper combo.

[@penrynbigbird]

We don't use the sway bars, but for bumps in the road, having the weight distribution hitch attached definitely dampens the effects of that bump, at least in our rig. We drive a 1-ton truck pulling a 31' TT. We have none of the four reasons you mentioned for having it...

[@spankymagee]

Load your trailer right is the biggest key

[@therealdeal67]

Great information video!:You hit all the key points. When people buy a travel trailer or truck to pull it with, it's extremely important to do a thorough research on all the weight of the truck and trailer to see if one needs a weight distribution system put on. David and Jenni y'all have the perfect set-up. no distribution system needed. A important thing for people to know is watch your speed when towing. If the trailer started to sway when one is going to fast, it would to late to slow down because the trailer or truck would have done flipped. Y'all due a super job on speed control. Take care and God Bless You Both.

[@burncon2]

You asked for comments…so: I’ve been towing for 45 years. Judging by your photo, you may need to lighten your load if you plan to continue not using & given the 1/8” steel used on hitch frames today, I can’t blame you. WDB’s will fold those frames in a heartbeat on a bad bump. You are far from level and an emergency FULL stop will educate you. I tow a 17MKE with a 3/4 ton diesel. I don’t use the load bars but DO use anti-sway. One trip on the wrong day on I-80 through WY will educate you. Happy towing. I’ll pray for you 😊

[@fastdadgarage-northsouthch4418]

The white Ford was a perfect example a vehicle that needs one.

[@gavinbitz2563]

Be smart and pull a trailer. Great job on the video.

[@Factory400]

I chose to get a Blue Ox WD hitch on the basis of 'just in case'. Saved me a lot of time researching and testing to figure out if I really needed it. What I did NOT want is to learn a hard lesson in the middle of nowhere. I put it in the insurance expense category.

[@mrc1539]

A few things you forgot to mention, how much tongue weight the trailer has, how much your rear bumper drops when hitched ,and how much the front bumper comes up when hitched. The only true way to know is by going to a scale and weighing each axle unloaded, then again with everything loaded and reddy to hit the road. And you are right about salesman , most are more into sales than safety.

[@michaelf.3846]

Keystone's suck-ass it's all about Grand Design

[@BadmunkyWRX]

I tow a 5,400lb 24.5 foot Camper with my 2015 Silverado 2500HD without a weight distribution hitch. I have towed the trailer in high cross winds with no problems. And the truck and trailer both sit level when loaded and hooked up. I have never felt I needed a weight distribution hitch or sway control. Now my mom pulls a 32 foot TT thats 8,200lbs loaded with a Ram 1500 and she MUST us a weight distribution hitch or her truck will almost be sitting on the bump stops in the rear when hooked to the trailer. I would likely also need the weight distribution hitch if I was towing her trailer. Tho I have never tried to pull her trailer to be sure.

[@bofa83]

Just watched a video where, because of the way a wdh puts weight back on the A frame of the trailer, they hit a bump in the road and it buckled the frame of the trailer. Mostly because of the thin metal used to make the frame, but it probably wouldn’t have happened without one.

[@dougsyd1662]

I probably don't need my weight distribution hitch but I feel better using it anyway.

[@Glock2201]

You don't need one because you have a 3/4 ton truck. I have a 1/2 ton and have a trailer with a dry weight of 5800 so it is a great idea for me to use one.

[@FateUnbound]

Absolutely, 1/2 ton pickups towing a travel trailer like this definitely need a WDH 👍

[@shiptime8108]

I’ve been towing for a long time and I never heard of these until recently. Is this needed because most people pull overweight and highway speeds+? I really wish a license was required for towing after a certain size. I have a Cdl and cringe every time I see somebody fly by with a massive camper. Stay safe folks.

[@docholiday1034]

If you cringe? Maybe stay off the interstates. Guess you never pulled doubles

[@jamesm568]

You should be able to pull a travel trailer safely at 80 miles an hour when properly equipped for short distances(passing) and continuously maintain 70 MPH full-time if desired.

[@burlingtonbill4687]

When in the army 70 to 72, Rosie and I went from fort to fort with everything we own in a 1966 Mustang. ( 66 mustang, written by me on burlington bill You Tube) Shortly following my service we purchased a pop-up (tent camper). After two of these units we researched and talked with lots of RVers and decided on a fifth wheel. I think now we are on our 6th unit and have never regretted our choice. Everyone has to decide what is best for them, but the fifth wheel is great for us. We have logged many miles from Maine to California to Alaska and down to the Padre Islands in Texas ( cue my song Can't get there from here). We are now in our 70's and just ordered a new truck to keep us going for years to come. I like your channel. Keep up the good work. Maybe see you on the road sometime. Check out my music!

[@kenschmidt6522]

Also, airbags/airshocks are no substitute for a distribution hitch.

[@greggdpa]

3 years? Hmmm I’ve pulled very heavy weights for 36 years. I think that makes me more qualified? By your own analogy If you have this equipment, USE IT! Sway may not happen, but when it starts, it exasperates itself! Once it reaches a certain point, hang on for life! I’ve witnessed dozens of ruined vacations because of your assessment!

[@marlomarteja3007]

I agree. Why wait until you get a sway? Why put on a seat belt? I've been driving for over 3 years and no accident. I can tell you, you don't need a seat belt. Thats what he sounds like.

[@clintfaulconer9816]

He isn’t wrong it really is a simple math problem to determine. However driving experience and comfort level is also a very big factor. If you’re not familiar with towing there’s really no harm in it. The big uptake in the weight distribution/sway control is simple actually the last 15 years or so camp trailers have gotten lighter, taller and drastically increased ground clearance height. Trailer sales always up sell the stuff 1. To make money and 2. To stabilize the whole thing if you’ve got a diesel and a pre mid 2000’s trailer it’s gunna go down the road without all this stuff. But again driver comfort level and confidence is really the deciding factor at the end of the day.

[@tombrennan6312]

Weight distribution and sway control are different subjects. If you put about 12%-15% of your loaded trailer weight on the tongue you won't sway. Hitch makers encourage fear of sway to sell gadgets.

[@jdmixon80]

I completely agree! A WD hitch is just a bandaid. Use the proper sized tow vehicle.

[@tombrennan6312]

@@jdmixon80 IME many RVers know how much they can pull but no idea of how much they can carry-their payload.

[@jdmixon80]

@@tombrennan6312 Great point. When towing payload comes into play. Most people only know tow rating.