Faulty what condenser fan motor or relay???

Is it a bad condenser fan motor or a bad relay. We are going find out www.amazon.com/shop/miheatingguy
Milwaukee 2131-20 M18 ROCKET Dual Power Tower Light
amzn.to/3pe2hYH
Milwaukee M12 Surge Hydraulic Driver Kit 2551-22
amzn.to/3n5offb
Makita E-01563 Impact XPS 3 Pc. 6" Magnetic Nut setter Set
amzn.to/2JdAcku
Milwaukee 48-22-6330 Tongue and Groove Pliers Set
amzn.to/3kfch0R
GoPro Hero 8 Black Action Camera with Accessory Bundle
amzn.to/34AGamf
Veto Pro Pac Tech XL Tool Bag
amzn.to/2U1QqPF
OLIGHT Bundle H2R LED Headlamp, 2300 Lumens Rechargeable Flashlight
amzn.to/370rGiq
Amprobe AMP-320 Clamp Meter
amzn.to/2GNxUHe
Fluke 117 Electricians True RMS Multimeter
amzn.to/3iFZP9t
Milwaukee 2364-20 M12 Rover
amzn.to/2HNvitK
Milwaukee Rocket light 2132-20
amzn.to/341OTPm
#MIHeatingGuy

[@brandoncoffee8044]

Just a thought... could you just block off the top of the non working condenser fan motor? At least with one working it could still pull air through the condenser and not through the opening of the bad motor. Just to get them some cooling until the motor is replaced. As long as you head pressure didn’t get to high of course. Keep the videos coming. Glad to see your back!!

[@ThermalDynamicSevices]

I take the black wire and put it on the load side of the contactor if I question a relay or fan lol

[@donnierobertson3088]

Nice job and video

[@notanewbie1718]

You go to a lot of trouble carrying that camera around to your jobs. It is appreciated.

[@andygalindo8978]

Bad condenser motors hold a charge with the capacitor. Since fan blade don’t turn it won’t let some charge escape. I may be wrong.

[@RyanAnderson-jj7xj]

Switch fan leads, quick and easy, If it still doesn't run. Done and gone.

[@RJMaker]

I bet you got capacitor bit. :-) I have learned the hard way to shunt any caps with a working voltage 460v and above.

[@throttlebottle5906]

yep, just takes a bad motor winding open or loose wire and contactor to open/chatter at just the right portion of AC sine wave to leave a cap charged to line voltage or higher from motor running/back emf on relay/disconnect open, then you grab and ZAP. Also it will be "DC" high voltage charge with enough current to kill you instantly, so BEWARE a meter on AC won't read anything or just momentarily blink a number, many techs do not know that making it more dangerous to themselves :)

[@bigclivedotcom]

I never trust the discharge resistors in capacitors (if they even have them). They often fail over time. The meter wouldn't have shown much if it was set to AC as the residual charge is DC.

[@throttlebottle5906]

the start capacitors usually have an external bleeder resistors, the run capacitors do not and that's a run capacitor :)

[@raymondleighton9059]

instablaster...

[@mechanic8031]

I like your content, good luck dear friend.

[@rayesboy3]

As Steve Lav world say, “She ain’t no Taj Mahal”

[@johncarcamo6772]

you know Steve has an APP its called Steve Lav Soundboard

[@throttlebottle5906]

I can only guess one winding of bad cond. fan motor open, and it charged the cap when powered up or when contactor chattered at unhooking jumpers. though it was unclear what you was touching when zapped. it could simply be stray/inductive voltage from wires in close proximity, say between thermostat and line wiring causing very low current yet high voltage. on 120vac stuff it;s not uncommon to see as high as 90vac, it could be higher on other voltages and will certainly tingle/wake you up brushed against the back of a hand/finger or other body part. flat grabbing the leads would make it go to near 0 and not feel anything

[@jerryr6713]

amp clamp suspect fan motor wire to see if power present.

[@hvac97849]

I would guess that the fan never turned off due to the stuck relay, hence premature failure. Nitrile gloves would be in your best interest, just sayin

[@amadeusrocks4967]

the cap most likely