First drive in my cammed Silverado on 37s | TSP chopacabra cam

[@joshritchie_media]

You’ll never hear a set of tires howl more than my Mickey tompson deegan😂

[@blameitonchina2022]

I got those mine are so quiet

[@joshritchie_media]

@@blameitonchina2022 well then mine r cupped 😭

[@joshritchie_media]

Great work 👍 looks and sounds even better

[@harleystillwell7519]

Thanks man!

[@joebass517]

Looking & sounding great!! 👍 Z Life.

[@dylanfinch6186]

Your face when you turned it on 😂

[@boostboy787]

You do hp tuners after the cam or you used the ct3 tuner u already have to tune the truck?

[@harleystillwell7519]

I sent my computer out to mailordertuner.com and he sent me it back tuned and ready to go

[@loweredyote8416]

Just curious on why you’d do shorty headers AND straight pipes? If you’re gonna have such minimal exhaust, you shoulda atleast made a difference with some longtubes

[@harleystillwell7519]

Well I had the straight pipes before I did the motor work. And I didn’t really want to mess with long tubes but I needed headers because the stock manifold’s were in such bad condition. So I wanted to go with shortys for now so they’d just bolt right back up but I can easily Change that in the future

[@loweredyote8416]

@@harleystillwell7519 ah that’s fair. I just kinda assumed you’d done full new exhaust. I found this vid while trying to find a exhaust setup for my Escalade since I’ll have Same cam

[@harleystillwell7519]

A cammed Escalade? That’s the most bad ass thing I’ve heard today🤟🏼 and nope just left all that alone and focused on getting the engine taken care of for now

[@loweredyote8416]

@@harleystillwell7519 yessir. 04 with the lq9. Cammed, ported/polished ls3 style heads, longtubes, 3200 stall convertor. Gonna do a fast 102 manifold later down the road. Should make 380-390 rwhp spinning truck tires thru an auto

[@csosbe251]

​@Harley Stillwell is this motor a 5.3? Dual straight pipes?

[@lunatic_durango5154]

One question, is ur transmission upgraded???

[@harleystillwell7519]

Yes it’s a built 4L65e with a shift kit, different servos and pretty much anything to make a 4l60 as strong as possible

[@ixxloose]

What heads did you put on it? Stock dish pistons?

[@harleystillwell7519]

Stock heads just had them cleaned up and valves checked and new seals and springs to go with the cam. Stock 230k mile pistons

[@chrishansen7004]

What gear ratio you have? I'd look into a set of 5.13's, I imagine with 37's it would feel like a stock truck with 4.10's. I know how long those gears feel in a 4L60 way too well 😅 if your really balling in the dough look at a gear vendors as well im pinching pennies for one whenever I get around to building my truck

[@harleystillwell7519]

I have 342s😂 and somehow it felt pretty normal in town except for on the interstate it won’t even go into 4th gear till you let off haha, so it just screams in 3rd

[@chrishansen7004]

​@@harleystillwell7519 damn man that's gotta be rough, definitely get a set of gears in there soon. tall gears and big tires puts alot of stress on the trans

[@maikololiver293]

How much is the price for the edge tuner

[@harleystillwell7519]

Mine is just a monitor, around $300. The tuner is more like $600

[@maikololiver293]

@@harleystillwell7519 another question, the edge shows you what speed you are in, I say when you are in overdrive

[@benjamintchappell8557]

How much did it cost for you to rebuild your motor?

[@harleystillwell7519]

I have a stack of receipts I’ve been planning to go through and make a video. But if I was to guess I’d say a little under 2k

[@alexortega1237]

will you make a video on how you did your brush guard with the body lift?

[@harleystillwell7519]

Yes sir I will

[@cody6.6max]

Wha 2014 bumper goes on a 2500 lb7?? 2500 or 1500 2014 ?

[@harleystillwell7519]

2500

[@harleystillwell7519]

Well either, the plastic on top is just different so 2500 would fill the gap better

[@tylersmothers1724]

How does this cam do with towing?

[@harleystillwell7519]

It does okay ish is all I’m gonna say. My truck has 3.42 gears which absolutely suck so going down the interstate it doesn’t want to just cruise in 4th gear with a trailer anymore. But I pull my 2,200 pound boat a couple times a week a short distance and it feels the same as it used too. The only noticeable difference is interstate cruising

[@tylersmothers1724]

@@harleystillwell7519 thanks for the reply I really appreciate it as I have the same gears. I don’t do alot of hwy towing but have a landscape company and do a lot of city towing. How is it in the city?

[@harleystillwell7519]

Totally fine in the city I would say you’re perfectly fine. Plenty of torque to get moving it just doesn’t like to cruise over 80 mph. You’ll get a lot of customers when they hear your truck chopping!

[@tylersmothers1724]

@@harleystillwell7519 awesome again I really appreciate ur feedback. it’s been hard to find a driving video of these cams. Stuck between this and the truck Norris cam,. They’re basically identical just slightly Different sounds. I also have a built trans with a stock converter like you so I’ll be good in that department. My truck has 280k with a lifter tick,. I’ve got a brand new short block 5.3 I just Got from machine shop. Going to just do a mild build looking for around 425ish! You gained a follower for sure,. Love Your truck and build 🤩

[@harleystillwell7519]

Sounds like you’re all set up😎 thank you man i appreciate it!! And good luck. You’ll love either cam

[@timmacrae328]

Did you install the roof rack?

[@harleystillwell7519]

Yep. It came off of a suburban and I cut it down to fit

[@cadenfaris1005]

Does it chop in drive?

[@harleystillwell7519]

It does a little bit, you can definitely tell it’s cammed. But I think my tune has the idle set way to high. It’s at like 850 rpm at red lights so no it doesn’t chop like it does in park

[@Joecookjr1]

What size lift?

[@harleystillwell7519]

3” body and 4” rough country suspension

[@lspaul13]

What tuner is that

[@harleystillwell7519]

Mail order tuner out of Texas

[@IsaiasGarcia.IG.]

Do u have link to tunner or info ph number website

[@harleystillwell7519]

mailordertuner.com/?gadid=495484421197&gclid=EAIaIQobChMIqpLC0J3X_gIVQQGtBh1ZVADCEAAYASAAEgK_EvD_BwE

[@boostboy787]

You do hp tuners after the cam or you used the ct3 tuner u already have to tune the truck?

[@harleystillwell7519]

I sent my ecu to mail order tuner down in Texas for the tune. I just use the cts to monitor it