Fitting a Victron Smart Shunt to My Adria Twin

[@kev1ncook]

Hi Nick, thanks for this, it really helped me unravel the mystery of what all those wires were doing. Followed your guidance and no power to the shunt…. Changed the fuse in the supplied lead all now working!

[@nickharper6436]

Glad your up and running and thanks for your comments.

[@bc312070]

Hi Nick. Great demo of fitting the smart shunt. I find it interesting to monitor what's coming in & out from the solar panel & DC TO DC charger to the lithium battery, I am glad you also fitted the aux cable as I did to the starter battery a lot don't it's so easy now to check the voltage, puts your mind at ease. Great stuff!

[@nickharper6436]

Many thanks for the comments Peter and glad you found the video useful.

[@videodomination]

Thank you, this was very useful! Keep it going!

[@nickharper6436]

Many thanks for the comments

[@jontymo]

Thanks Nick - looking forward to see the setup for gas

[@brianreay4104]

Just an inspired guess,that stray harness in your cab battery area is similar to the one which plugs into the interface box for my tow bar wiring. My harness was added when I had the tow bar fitted, perhaps yours is supplied with the harness or the vehicle had a tow bar previously. On my Ducato (2018) based motorhome the other end plugs into the vehicle lighting harness by the rear axle, near side. There is a large connector there. Another spur goes to the tow bar.

[@nickharper6436]

Yeh it could well be, apparently other Adria Twins have the same so it’s obviously meant to be unconnected. I got the vehicle from new so I didn’t have a tow bar previously but it was a factory option so I think your guess is probably right. Many thanks for your comments.

[@betterthanlastweek9670]

Exactly what I needed. One is on it's way, thank you!

[@nickharper6436]

Cool, glad you found the vid useful!

[@PlatisTobbe]

Great video, I also have that Shunt but I havent installed it yet!! You have a new Subscriber

[@nickharper6436]

Thanks very much for your support and I hope the video helps with your installation.

[@neilwr7442]

Great video, clear instructions. Thank you👍

[@nickharper6436]

Many thanks Neil and glad you found it useful !

[@MarkSlaski]

Really helpful video Nick. It looks like you were able to lay the seat on its back while you were fitting your shunt - were you able to keep seatbelt pretensioner plug connected during the fitting?

[@nickharper6436]

Hi thanks for the comments and yes it wasn’t disconnected!

[@wynparry971]

Thank you for the video very helpful.Can you tell me if there are any airbag issues when taking the seats off ?

[@nickharper6436]

Thanks for the comments. Not for me personally as I left every thing connected and just laid the seat to the rest giving access to the batteries rather than taking to seat completely out of the van.

[@porcorosso]

Thank you for the video My car is also Adria TWIN It was very helpful！ I subscribed to your page.

[@nickharper6436]

Many thanks for subscribing and I’m glad you found it useful. Happy Twining!

[@davebrown4719]

Hi Nick, great video. Please could you put a link to where you got the 2 off negative hook-up cables and bus-bar box. Thanks in advance Dave

[@nickharper6436]

Hi Dave, thanks. If you search T Tocas bus bar in Amazon it will come up. It’s not cheap though! £33 😳. The 2 negative leads I got from Halfords. Hope this helps Dave

[@chrisforbes2124]

Hi Nick. I am going to do the same upgrade as this. Thanks for a great video. Can I ask the approximate length of the cable used. My campervan has the same electrical setup. Thanks Chris

[@nickharper6436]

Hi Chris, do you mean the battery cable? If so I bought them pre made up at Halfords. They were about 12” I reckon.

[@PrinceHale]

Hi Nick, great video! Can I just check, what diameter cable from shunt to battery did you use and were all connections M10?

[@nickharper6436]

Thanks for the comments and yes M10. The leads from shunt to battery were bought from Halfords I’ll have a look later

[@PrinceHale]

Thanks again, I installed this following your video today. The seat with the cables attached was a pain, had to find something to perch it on whilst undoing the plate to access the batteries!! I used 16mm cable each 9” long with an M8 one end and an M10 the other. All sorted and working a treat.

[@nickharper6436]

Cool, sorry I didn’t get back to you regarding the diameter of the cable Kevin. Anyway looks like your sorted now 👍

[@mikegilsenan1962]

Thanks for the info Nick...! What value did you input for battery capacity in the app? Was it for a single battery (e.g. 100 Ah) or X2 batteries 200 AH? Cheers again!

[@nickharper6436]

I put 200ah but aware that I can only use 100ah max to preserve the life of the batteries. I then set the discharge floor to 50%. Hope that helps and thanks for the comments

[@lukejamesharper4382]

Great video!

[@nickharper6436]

Thanks Luke

[@Braapncamp]

Brilliiant video Nick! I have the batterys BMS with app doing this for me, very useful. Can't imagine to be without it now. Cool LPG bottle, can You refill it by yourself? I have two PC10 (10Kg lpg) bottles that looks very similar (composite). In the van i use two steel P11 (11Kg lpg). The PC10's was used all time before and are alot less weight to handle. I have to refill them at specific station where tve staff must do the work or just swap tbem in an 24h automat. (Both P11 and PC10). Keep it up, all the best! /Mattias

[@nickharper6436]

Thanks Mattias, The safefill bottles are designed to be filled by yourself at the LPG pump. Once I’ve filled it I’ll post a video 👍

[@Braapncamp]

@@nickharper6436 Thats interesting, over here they must be fixed installed. This is news for me. Cool!

[@nickharper6436]

Apparantly there are some garages over here that think you are filling an exchange bottle but once they see it is a safefill bottle hopefully it won’t be a problem. Morrisons supermarket garage are a safefill partner so I no I can fill there. Getting exchange bottles changed here in the ik is getting extremely difficult !

[@martinalund3384]

Great video, THANKS!

[@nickharper6436]

Many thanks Martin and glad it was useful !

[@duncancleveland2221]

Great video Nick, a couple of questions, 1) have you thought about lithium? and 2) where did you get your safefill, everywhere seems to be out of stock. Thanks

[@nickharper6436]

Hi Duncan, yes I have thought about lithium and will probably go that route once my AGMs are past their useful life. I believe www.marinepowerltd.co.uk might have some in stock. That’s where I got mine from.

[@sandymerry9172]

Enjoyed your video Nick. Just about to do the same. Could you please tell me what gauge cable you bought from Halfords and were they made up with the required connections or did you do that yourself. Many thanks.

[@nickharper6436]

Thanks for your comments Sandy. I think they are 16mm and I had to have a bigger spade connector to allow it to fit the shunt which have M10 bolts on I believe. I got a local dealer to fit the spades as I didn’t want to purchase a crimping tool just for that job. Hope this helps!

[@sandymerry9172]

@@nickharper6436 Cheers Nick. Made my decisions much easier.

[@sccobyste]

We have just ordered an auto trail but wondered what’s the lead time on these

[@nickharper6436]

Not sure on auto trail to be honest but Adria is about 18 months. The dealer will be best placed to advise you on that.

[@mikeainsworth5840]

Hi Nick, great video. Just subscribed to your channel. I have a 2020 600 SPB as well so I'm very interested in what you're doing. I'm going to fit the battery monitor so your video was very useful. Can I ask what you mounted the bus bar too? It looked like you screwed it to the battery.

[@nickharper6436]

Hi Mike, thanks for subscribing it’s appreciated. So I secured the bus bar and the shunt with double sided 3m sticky pads. Probably the screws you can see on the bus bar are to secure the cover.

[@brianreay4104]

A helpful video, thank you. Can I ask, how do you find the Bluetooth range? I know what to expect from normal BT devices but some have commented elsewhere this device has a short range for BT.

[@nickharper6436]

It certainly works ok as far as I’m concerned and I can check the power from the bed at the back of the van and the shunt is under the front seat. It has a signal strength indicator on the app and it’s at full strength when I’m at the back of the van! No problems as far as I’m concerned and I did see those comments myself and did wonder.

[@MotorhomeDIY]

I don’t know if you noticed tho but your starter battery also drains when you turned the lights on the starter battery dropped This did it with mine after 8 months I had to change the battery I don’t use the wire anymore to the starter battery I have a battery sense Victron on the starter . Apparently it does this with the starter battery with bad ground 🤷‍♂️ I couldn’t find bad ground so removed the wire fed up of the battery drain And yes even with a new battery I tried it drained agsin

[@nickharper6436]

No I didn’t notice but thanks for the heads up. Interesting !

[@alanbenham4139]

🙏

[@kev1ncook]

Hi Nick, thanks for this, it really helped me unravel the mystery of what all those wires were doing. Followed your guidance and no power to the shunt…. Changed the fuse in the supplied lead all now working!

[@nickharper6436]

Kev glad the fuse sorted the problem. There is nothing more frustrating than something not working when it’s all installed correctly!