Fitting of Electrochemical Impedance Spectroscopy data with Zview 3 2b!!

[@juanengineer9937]

Here is a new link for those that can not download it from the previous location! I would appreciate you to give a Like & share the video, and please SUSCRIBE! Hope it works for you all. Thank you!! Download the Zview 3.2b for unlimited EIS data point fitting: drive.google.com/file/d/1_cAKdfg9CUqvntm-H0FCAsIO9rTGKuLg/view?usp=sharing

[@mome123]

Very good video! But the version you uploaded, only show limited points, its the demo version. Do you have a cracked version ?

[@MrShiska]

Hey juan ! Thank you so much for the help! I have a question after following every step mentioned by you in the video when I click the run fitting button it gives me an error that the input pending in the graphic 1. Can you help me what could I be doing wrong. Again thanks for all the help!

[@sonu-yadav-1001]

@@mome123 vd.y

[@ottikam]

any other link to download the software

[@yogapalani4420]

this link is also not working

[@이홍근-e7b]

What a great video. Thanks a lot!😊

[@muthusaru3527]

Thank you so much really very useful plz continue yout valuable knowledge to us..

[@chaithrajchaithra1594]

Thank you so much sir

[@anyeshachakraborty5056]

Could not download Zview from the link even from the comment link. Please provide me the link to download the software and thank u for ur wonderful work

[@inimuftiali]

thanks a lot man

[@logeshm.5416]

Dear sir, Kindly teach with cursor. I cannot identify that where you are clicking.

[@juanengineer9937]

Oh I'm really sorry, in which part/minute of the video specifically do you need help with?

[@priyankaroy6804]

My solution resistance is negative with standard randal circuit as equivalent circuit what does it mean??

[@mani2263]

i am facing this issue too. Did you resolve it?

[@akshitasharma5340]

unable to download from the link...plz provide the new link

[@Khanjar996]

I have a question ? how do you understand about make resister first and the parallel (?) can you please explain.

[@juanengineer9937]

When you are designing the equivalent electrochemical circuit, it has to have physical sense with the system you want to simulate. In this case it starts with a resistance because there is a solution-metal phase, so it's the solution's resistance, I know is almost minimum, but still you have to add it to the circuit. The parallel goes after, because according to research in the metal surface its formed a double layer capacitance (Cdl, constant-phase element) and at the same time, the metal provides resistance therefore a resistor. So when making the equivalent circuit you should look for all that is between the electrodes. Kind regards

[@sumedharajput7013]

Thanks for such helpful video. I have a doubt - How to select type of data weighing ? I means how would I know that for my data, which data weighing option should be chosen ?

[@anamartinezm]

Hello, it is not very clear where you click or what you do without the cursor visible. Anyway, I got what I was looking to learn. Thank you.

[@juanengineer9937]

Gracias Ana, me alegra que te haya servido!

[@saadawan7247]

can you tell me the how to plot nyquist graph in Zview ..Thanks

[@messaoudmeraghni5606]

thank you so much for everything can you help me how to calculate double layer capacitance Cdl

[@avatar7gavric]

Hello...when I save excel data to .txt format it doesn't wanna to load in ZView...do you have any solutions? :)

[@juanengineer9937]

Are you using period (point) as decimal separator?or try to save your data in notes block from windows, that's how I saved it. Please send me an email with more details (video, picture) of whatever appears when you try to download your .txt to Zview.

[@ElectrronCoundoctivity-hc1hf]

I can't fitting because i have at least two points in that side that is near to circle

[@patnayakunitulasirao4524]

Not working above link

[@UsmanAli-lq9hj]

Hello, i Have a problem. How i Can draw the orginal values and fitted values on Origin Software. I Can Copy Original value from the clip board. But from Where i get fitting values to draw on Origin.

[@juanengineer9937]

Hello Usman, 1. Choose the fitting values in the uppercenter tab, (where is shown "EIS.txt" in minute 4:06) 2. Afer choosing the fitting values, just save the document with as txt and the open it in Origin. Is this what you were wondering?

[@nehatewari2626]

hello, could you do one video for the one with warburd impedance, mainly seen in batteries? as it in not fit by instant models. thanks

[@nehatewari2626]

also , this isnt properlt fit, how to properly fit it?

[@juanengineer9937]

For sure, can you send me an email about the exact batteries model you are interested about? [e-mail]

[@juanengineer9937]

@@nehatewari2626 the proper fit depends on the elements you will add to the Equivalent Electric Circuit but always in accordance with the physic sense of your experiment, every element in the circuit should represent the behaviour of an element in the real world. For instance, to represent a physical layer that hinders the flow of the current you will use a Resistor(R), in case you want to represent charge-storing you would use a Capacitor(C), or more accurately a Constant Phase Element (CPE), and so on. In this order of ideas, it is bettter to choose a model that has physical sense with no so perfect fit over a model that fits 100% but has no physical sense at all.

[@muthusaru3527]

How can we find the equivalent circuit for our data.. Does it vary for each and every data

[@OnionManSteve]

It is entirely dependant on the type of material you have (semiconducter etc). The best way I have found is to look in the literature for similar materials, and develop a model based on the published data.

[@atmanemanou4087]

thanks

[@jjlqq8286]

Hi, When I input my data (Frequencies from 20Hz to 2MHz ), it just shows a part of data, (Frequencies from 20 to 300Hz). I don't know why.

[@juanengineer9937]

You should do right click into the lZl vs Frequency graph (Hz) and then arrange the domain, the ranges of frequency that you would like to see in the graph.

[@deepikayadav3755]

do you have the cracked link for Zview?

[@elquimicodavid]

Hola Juan. cuando cargo los datos desde el archivo txt me dibuja las curvas solo en un rango de frecuencias (el intervalo de frecuencias que he usado va desde 10E5 a 10E-3 y entre 10 y 0.001 Hz no me lo dibuja las curvas. No tiene que ver con la escala de los ejes porque ya las he modificado. tienes idea de que puede pasar?. gracias. un saludo

[@juanengineer9937]

Hola! depronto tiene que ver con cómo tienes escritos los datos, es decir el orden o la notación, como por ejemplo poner "." en vez de ","

[@sdfgvvjs434s]

que tal Juan, esta version de Zview tienes el crack o algo asi? para hacerlo full, o ya viene full ?

[@juanengineer9937]

Hola si, es un crack Daniel!

[@katiahebbache1936]

Have you software voltamasterPGP201, because i need it

[@mani2263]

Can anyone share ZView software?

[@anilohlan8025]

From where i get the cracked version of Zview

[@mome123]

did you find it ?

[@juanengineer9937]

@@mome123 Please send me an email to [e-mail] requesting the version of the program.

[@juanengineer9937]

Please send me an email to [e-mail] requesting the version of the program.

[@juanengineer9937]

Hello! Please send me an email to [e-mail] requesting the version of the program.

[@vipin_cyriac]

Unable to download the software.

[@juanengineer9937]

Hello! Vipin Please send me an email to [e-mail] requesting the version of the program.

[@achwa7665]

@vipin do you have the software :!

[@kurniapamulianti4559]

I really need cracked version of Zview, please send me the link download. I've sent email to you, thanks in advance

[@rajeshwarimirji1928]

Link is not working I hope

[@juanengineer9937]

Hello, Please send me an email to [e-mail] requesting the version of the program.

[@JessicaSmith-j4v]

Kristian Street

[@쌍거풀단발]

얍쓰~

[@teerapatkotpatjim1226]

Unable to download the software

[@kurniapamulianti2723]

I really need cracked version of Zview, please send me the link download. I've sent email to you. Thanks in advance