FIXED. PS3 Slim Green Light of Death (GLOD). No video/No audio/No controller sync

[@abrahamadekanye5714]

Wow great repair job👍 Mr Idrees, i have like four consoles with this exact fault, will chk the bison resistors. Great job Greetings from Nathan.

[@michaelolayinka441]

Did this fix it for you?? 🥺

[@DarthSimous]

Great repair, Master Idrees ... Another 3000 series Slim saved ...👍

[@bonk_playz9495]

Hi, my ps3 slim has a similar problem where it turns on but there is no display output. Also the controllers work absolutely fine and are able to sync to the console. There is no video output on both AV and HDMI ports. Please help

[@idreestech]

It’s good to hear your controllers are syncing since that confirms the system is booting. Here's a step-by-step guide to troubleshoot the no-video output issue on both AV and HDMI: 1. Reset Video Output Settings Sometimes the PS3 outputs a resolution your TV/monitor doesn’t support. To reset: Turn off the PS3 completely (solid red light). Hold down the Power button: Keep holding after the 1st beep (Power On). Release after the 2nd beep (about 5-10 seconds). The PS3 resets its video output to standard definition. Connect using both AV and HDMI (to ensure you test both outputs). 2. Test HDMI/AV Cables and Ports Use a working HDMI cable on a known good TV. If still no display, test with the AV cable (red, white, yellow wires). Ensure ports on the TV and PS3 are not damaged. Test another HDMI input on your TV or a different monitor. 3. Boot into Safe Mode Safe Mode can bypass video configuration issues: Turn off the PS3 (solid red light). Press and hold the Power button: 1st beep: Power On. 2nd beep: Power Off (keep holding). Release the button after you hear two quick beeps. Safe Mode menu should appear. If successful, choose Restore Default Settings or Rebuild Database. If Safe Mode doesn’t appear, it’s likely a hardware problem. 4. Check the Hard Drive A failing HDD can cause display issues. To test: Power off the console and remove the hard drive. Turn on the PS3 without the hard drive installed. If you see a prompt asking for the storage device, the HDD could be faulty. Replace or reformat the hard drive. 5. Internal Hardware Issue: RSX (Graphics Chip) If the above fails, the issue may be with the RSX (GPU): Symptoms: System boots, no display output, controllers work. Cause: RSX chip’s solder joints may have cracked or weakened over time. Possible Fixes: Reflow the RSX: Temporarily fixes solder cracks using controlled heat. Reballing (Permanent Fix): Replace old solder balls under the RSX with new ones. Note: These are advanced repairs. If you’re not confident, consider taking it to a professional. Next Steps Start with the reset video settings and Safe Mode attempts. If no success, test the HDD. If still no display, it’s most likely the RSX chip, and a reflow/reballing is needed. Let me know how it goes, and I’ll help you further! 👍

[@bonk_playz9495]

@idreestech Thank you Sir! I'll try out these fixes and update you accordingly

[@bonk_playz9495]

@@idreestech Hi, I have tried all the above mentioned fixes but none of them work. When I boot it into safe mode there is still no display . However if I boot it into safe mode and try turning the PlayStation off I hear 3 quick beeps. I've also tried removing the HDD but that doesn't not work. I've seen a youtube video on how someone fixed a problem similar to this by adding coins between the rsx chip and the heatsink. The uploader stated that this was done to add pressure onto the joints which has loosen because of overheating. Do you recommend trying this?

[@sussysussy513]

My ps3 slim 3004b turns on for 1 second then off syscon shows error 3010 Do you know ho to fix

[@abdilnas7563]

That could be a faulty power supply, try to replace it.

[@davedm6345]

im having some similar but wen i apply pressure on cpu, then when not i power on and the green light going off. what could be?

[@idreestech]

@davedm6345 It sounds like there might be an issue with the CPU's solder joints, possibly cold solder or a loose connection. Applying pressure may temporarily reconnect the joints. A reflow or reballing of the CPU could help resolve the issue. If you're not familiar with these techniques, I recommend seeking assistance from a professional repair technician. Let me know if you need more details!

[@lynchdemartini]

If the resistor is bad will it be too hot to touch when the console is on?

[@idreestech]

I have never experienced like this.

[@pashamamedov6773]

Как он узнал среди кучи резистораз, что именно тот неисправен...

[@kdesignmail]

Great job! With my PS3 i can play for several hours, but if i turn it off and then on again it will not show image... i have to let it cool and then try again.

[@zerogaming8967]

My ps3 slim 3000 series turns on and then off after 3 seconds no light , changing the psu didn’t work

[@idreestech]

Please watch the videos I've created that address the errors at hand.

[@Mobile-Tech72]

hello bro ps3 only beap no any lights......?

[@AiNolimits14]

Im getting something similar its on but not showing any image no signal and stuck on green light hard drive blink but the ps3 fan takes like a minute to be on 😢

[@idreestech]

@AiNolimits14 It sounds like the HDMI encoder chip might indeed be the issue if there's no display but the console seems to function otherwise. You can confirm it by swapping it with a new one, the encoder chip for any signs of damage or overheating. If faulty, replacing the encoder chip should resolve the issue. Let me know if you need more guidance! kzbin.info/www/bejne/rV6ZoaR_pLOrl6csi=b7CrHmmUdt-SjSXZ

[@AiNolimits14]

@@idreestech I was thinking of that actually I'll check, ty

[@AiNolimits14]

@@idreestech then there's another problem the fan started making a big rapid noise like a jet , and it won't let me hold the power button for the second beep

[@idreestech]

Good luck with your repair!

[@idreestech]

Try this (kzbin.info/www/bejne/Z6vbf6elp8RkfJosi=oO_va5YXSjBVNCJZ)

[@sunnyhenry7947]

This is great job, please how can I can get this reading meter I mean the one for the resistor

[@michaelolayinka441]

I think i have a similar issue, it started as flashing black screens. Going in and out of HDMI display while gaming. Now it doesn't display at all. Can a jumper work for either the 0.387n &/ the 0.508n resistors?

[@idreestech]

Absolutely, the jumper will serve its purpose.

[@michaelolayinka441]

@@idreestech I'm doing that now 🤪 💣💥💣 Thanks in advanced

[@michaelolayinka441]

@@idreestech the jumper didn't work for the exact one you changed what do you advice, should I jump the one perpendicular to it. Cuz it failed to boot when I jumped the one parallel to it. My RSX is hot I'm not sure it's a reflow I need

[@t0mbell]

I have ps3 phat cechl with ver-001 board. After start- green light and no image/sound, and no usb voltage. Can i catch errors in this case via uart or i need to manually check board components ?

[@idreestech]

First get the codes.

[@lunarhail3559]

@@idreestechdo you have a video of you soldering the wires to get the code?

[@reshwan_]

I measured the 500ohm which shows 450ohm and the 55 ones is correct..do i need to change it? I think 450 is okey..so what causing the issue?

[@idreestech]

Maybe some other component causes it. It could be the GPU as well. HDmi port or its component.

[@Aleksa.09]

Why is ps3 slim so unreliable ?

[@rabiusharefbabina2844]

Pls my teacher I have super slim PS3 such is the problem like this how to fix it ?

[@idreestech]

You have to configure the fault. If you have tools, you can do it. I have made some videos on PS 3 super slim too. You can watch them.

[@RelaxingNature1-n6r]

How to fix PS3 HDMI flickering and blanking problem.3004 A model.

[@idreestech]

The HDMI flickering and blanking issue on a PS3 (3004A model) can be caused by a few different factors, ranging from HDMI cable issues to hardware problems. The cable might be faulty, so try using a different one. Inspect the HDMI port on both the TV and PS3 for any debris or damage. Sometimes dust or a loose connection can cause flickering. Turn off your PS3, then hold the power button until you hear a second beep. This will reset the display settings, which might fix any resolution or compatibility issues. After resetting, manually set the resolution to match your TV's native resolution (e.g., 1080p or 720p). Sometimes auto-detection can cause flickering if there’s a mismatch. Try connecting the PS3 to a different HDMI port on the TV. Some TV ports may have different processing capabilities that can affect signal stability. Connect your PS3 to a different TV or monitor to see if the problem persists. This can help you identify whether the issue is with the PS3 or the TV. In rare cases, the HDMI flickering can be caused by a faulty HDMI IC on the PS3 motherboard. If none of the above steps work, it could be a hardware issue that might require replacing the HDMI IC chip or inspecting the GPU for possible damage. If the problem continues after trying these fixes, the issue might be hardware-related, and further diagnosis or repair may be required.

[@RelaxingNature1-n6r]

@@idreestech thanks 👍

[@reshwan_]

whats the value of that resistor

[@idreestech]

I could not remember all component's values but for some. You have to verify it from another good motherboard.

[@kondwanibanda4219]

My ps3 slim has no display and the gpu is not getting hot

[@idreestech]

Check for the HDMI encoder chip or replace it with a good one.

[@szwnnn]

Me : Are you having a good time Mr. Idrees? Him : @4:52

[@idreestech]

I enjoyed fixing such a mess.😀

[@adangzls1655]

Hello, I have a fat ps3 with glod, I have noticed that the rsx does not heat up, do you think that is the problem? Thanks

[@idreestech]

Then check power section for RSX. Switching inputs on inductors.

[@MichaelDaponte-fy9ji]

Could you just buy the resistor

[@idreestech]

Yes, you can definitely buy the resistor! Just make sure to get the correct value based on the schematic or the part you're replacing. It’s a straightforward fix if that’s the issue. Let me know if you need help finding the right one!

[@MichaelDaponte-fy9ji]

@@idreestech thanks

[@mouhamedkhchini]

What model of resistor

[@idreestech]

?

[@bokkibeatz55]

Nice video once again not everyone will be able to fix it because not everybody can afford the oscilloscope try next time with the FT232R USB UART and cool that u use subtitles from now on✌

[@idreestech]

Fine.

[@BilalAhmed-hc5vm]

Bhai jaan mera PlayStation repair hu gaya hai ke nahi

[@clambone337]

My glod was caused by the rsx chip on my board

[@lawlietcodm]

did you fix it? how?

[@clambone337]

@@lawlietcodm i covered a Pennie in thermal paste put it on the rsx to see if glod would go away and it has been working for a good month almost its backwards comp i would get it fixed but its working so no need

[@clambone337]

@@lawlietcodm you also might have to use multiple depending on how bad it so if one does not work try 2 dont stack if 2 doesnt work try 4 if 4 doesn't that means the solder is not recoverable and needs reballing

[@clambone337]

@@lawlietcodm i also learned this trick from someone else in the youtube comments they said its a temp fix tho but for me i just put thermal paste on the coin and ofc put new paste on the chip i tried repasting to see if glod would go away but it only did once more pressure was added to the rsx chip

[@lawlietcodm]

@@clambone337 I fix it yesterday thanks God! I open the rsx chip and clean it and put a thermal paste in the middle and I put back the rsx and it's work!!

[@asadawad3604]

Ap kidar ho drees bhai

[@makvlogs2323]

Well done sir great job

[@Mehdi-x]

Me it's only when i put my hard drive

[@sergiojimenez3415]

You’re out of this world

[@Magsyboy]

All hail to master!

[@arshadalitv6112]

Hello

[@infinitymobile9922]

Good video ❤️

[@idreestech]

Thanks 😁

[@copleskas4889]

Bro you are my angel

[@manolitovj]

💪💪💪💪🧑‍🔧🎮🎮

[@jackrich246]

❤❤❤ Please do Live streams

[@idreestech]

Fine.

[@arshadalitv6112]

Assalamualaikum

[@idreestech]

WaAlaikuAslaam!

[@xpaydaymoney8552]

Does anybody know if this KZbinr has a Instagram or discord I can join

[@idreestech]

@xpaydaymoney8552 Thanks for your interest! I currently focus on helping through KZbin. Stay tuned for updates if I decide to expand to Instagram or Discord in the future!

[@xpaydaymoney8552]

@idreestech also I want to ask this I was wanting to this out curiosity have you ever tried to make any KZbin videos on how to fix the PS3 slim no red light of death I've seen barely anybody posting how online KZbin tutorials on how to fix and I've also got it on my PS3 slim cech 2001a I just got this thing a few months ago it hasn't been displaying it the red led standby mode light and it's hasn't been operating for at least 3 months now and no seems to turn anymore also what should I do about it information on how to fix it very very scarce online

[@xpaydaymoney8552]

@idreestech also one finally question do u have a Instagram or Twitter account i could message you on for more trouble shooting advice also I don't have Facebook

[@xpaydaymoney8552]

@idreestech could I get ur Instagram user please or not have a account I really wanted to ask on advice on how to fix the PS3 slim no red light of death issue please and thank you very much sir

[@idreestech]

Hi @xpaydaymoney8552! Thank you for your comment and the idea for a video. The "No Red Light of Death" issue is somewhat less documented because it's a rarer problem compared to other common PS3 failures. Here are some initial steps you can take to troubleshoot and possibly fix your CECH-2001A Slim model: Check the Power Supply Unit (PSU): Remove the PSU and check for any visible damage (e.g., burn marks, swollen capacitors). Test the PSU with a multimeter to ensure it’s outputting the correct voltages. If it’s faulty, replace it with a compatible PSU. Inspect the Motherboard: Look for damaged components like capacitors or resistors near the power circuit. Use a multimeter to check for shorts around the power ICs and main rails. Examine the Power Button Circuit: Check the continuity of the power button and its connection to the motherboard. Test for Standby Voltage: Ensure the 3.3V standby voltage is present. Without this, the console won’t enter standby mode. Reflow Solder Joints (if needed): If you suspect poor soldering or micro-cracks, you may need to reflow specific areas on the motherboard, focusing on power-related ICs. Replace the Power Management IC (if applicable): In some cases, the power management IC may fail and need replacing. I’ll consider making a detailed video on this topic to help others in similar situations. Meanwhile, if you need detailed guidance on any of the steps above, let me know! 😊

[@jamesavanzado450]

same model as yours, where do I buy the chip

[@piyushgamesoftwarerewa7793]

Nice

[@Armwrsling]

thx🤩

[@JhonDCHM]

Exelent

[@عمارالراجح]

استاذ ومعلم

[@asadawad3604]

Pakistan india Bangladesh

[@idreestech]

Pakistan

[@arshadalitv6112]

Sir please apna koi phone number de apse rabta Karna hai

[@idreestech]

Please join me on Facebook.