Hey Bob! This is Joshua that just ordered the throttle centering kit here in California! Hope this day finds you as well as it does me!!! The install of the kit went flawlessly. I followed your advice to get some tinker tweezers (a tool I now use constantly) and use a small parts tray, best advice in the whole video. I have my DIY drone working much closer to my DJI thanks to this mod. The shipping was crazy fast and the kit arrived two days early. While I had the radio open I did the mod to install openTX. Super happy with this radio, thanks for your help!
@UKGtrotter2k3 жыл бұрын
Good video Bob, now I know what I need to convert my flysky for my truck. Are you going to release a video on how to reprogram the remotes.
@AddamsPlayground3 жыл бұрын
You make putting that spring in look too easy LOL! It was a fight but I got it after a couple tries and thankfully did not launch it across the room. Thanks again for being a resource to get these kits and the great instructions!!
@HobbyconceptsLLC3 жыл бұрын
I have launched a few myself!
@scottsrcshop Жыл бұрын
Thanks for making this video Bob! Every rc car channel I watch always references Bob at hobby concepts and how killer of a job you do.
@ronhenney45462 жыл бұрын
Thanks Bob watching someone else do it is a big help always look at your videos for some guidance
@AndrewMcVinnie2 ай бұрын
Thanks! Kit came fast and went in nice and easy, as shown..
@lucverburgh9285 Жыл бұрын
Thank you, I followed the video from A to B and the installation went well. Great !!!!!!!!!
@appleby20873 жыл бұрын
Just have done mine while watching your excellent video. Thanks Bob, very kind of you sharing all your experience 👏👏
@AddamsPlayground3 жыл бұрын
I just ordered my kit to do the mod... well I ordered two just in case I send one of those parts into the void which I may very well do. Would rather have the insurance of having the backup! Thanks for the instructions and the kit to do this!!
@joeyclark7893 жыл бұрын
God bless you Bob. Yet again you've saved me time in checking and fiddling to see how things go together. I now have a radio ready for my king hauler project. Thank you
@franciscodelrio3950 Жыл бұрын
Thanks for the centering kit, Bob, fast shipping.
@dennybobsrcconstructionagc27962 жыл бұрын
Only one question. Now that the radio throttle stick is no longer in the down/idle position. How do you stop the alarm in the radio from going off other than tapping the LH joystick down?
@HobbyconceptsLLC2 жыл бұрын
The ST-FS8 has a setting to turn it off! Finally!!
@RCBirds3 жыл бұрын
Thanks Bob, that helps I have this problem for my next Clod Buster project. I need a desk transmitter with max 6 channels, a pistol transmitter will not fit to my ideas. No programming needed. But all these radios (I found) were for airplanes. You get several modes, but all throttels aren't centered. Alternative are teh car radios with 11 or more channels, but this a little bit overkill for a fun monster truck. Where are the good old times, when desk radios were used for cars, boats and planes. The conversion sets came along with the radio set and the changes were easy.
@BartBrunink3 жыл бұрын
I’m using it for a 6x6 clod. It will also do crab like steering. I only centered the left stick, and use right stick for mixing channels.
@Laurence2353 жыл бұрын
Hello Bob, Thanks for the video. May come in handy at a later date. If I may though, I'd like to add a comment from "way down South in Oz"... re; "putting all those self tapping screws back in...." When they are 1st factory installed, they cut their own thread into the plastic, be they pillars or just a flat surface. Now....when you replace the screws, if you just go to screw them in, you risk spreading/splitting the hole or breaking the pillar off completely. My suggestion, after many, many years (over 50) of maintaining all types of equipment, is as follows... Put the screw in the hole BUT turn it back wards until you feel it click into the original screw threads. Then just gently screw it home but do not over tighten. You don't need to be a gorilla when doing this. Just gently screw them home & then back them off a tad, say, a 1/4 turn. This re-leaves the pressure/tension on all the plastic parts, that may/will be caused by expansion & contraction in varying temperatures. Hope I did not offend. Stay safe.
@hoonigan11 Жыл бұрын
Just did the conversion awesome video thanks
@rascalracing44282 жыл бұрын
Just did it, went great with your awesome video! Thanks a lot Bob!
@oldskoolstudios252 жыл бұрын
Great video Bob, thank you so much. It was really helpful. I did only one little thing differently. Because of my fat fingers, I found it easier to hook up the spring to the clip when I put the bar in before the knob is put back into place. Worked really well as it all stayed in place nicely before I screwed the brackets in. Maybe you could give this method a try the next time you do another one up. Very informative, thank you very much 🙏🏾🙏🏾
@CarminesRCTipsandTricks3 жыл бұрын
Thanks Bob! Very few how-tos on FlySky Radios. Most say they're not great - and they're usually Sponsored by Futaba or Spektrum!! I use only FlySky Radios, with zero issues. My FAT Fingers may be the only obstacle! 😜 Carmine ✈🚂🚙
@willdoe39842 жыл бұрын
I have a couple of questions about this item. 1)- what dose the 2 Circle nubs are used for? 2)- can I turn on/off a set of lights with one of swatches at the top of the Transmitter? When it comes to fixing the forward/ reverse leaving the remote the way it came because if I'm carrying a heavy load and going down hill I'll slightly pull back in to the reverse Position so that way it acts as a j-break and I don't constantly have tap on it just slow it down ! But thank you for all the videos you have shared and worked hard on! Stay safe and healthy my friend!
@HobbyconceptsLLC2 жыл бұрын
You can use an electronic switch to turn lights on and off. kzbin.info/www/bejne/mIm2ZGCumrt7nbc
@CarminesRCTipsandTricks3 жыл бұрын
Bob.... I finally got around to doing this. I bought the Kit from you almost 5 weeks ago!! SECOND SET OF EXPERIENCED EYES.... After this Diabetic OLD Fart fought with that tiny Spring... I found it tremendously easier to hook the Spring to BOTH pieces first, GENTLY place them in their slots. THEN drop the Gimbal in!! You should really try it that way. 😁
@MammothPaige Жыл бұрын
Thank You for the quick shipping and great video
@frikkiebester88953 жыл бұрын
Watching this video made the job very easy! Thank you, just converted 2 radios in less than 10 minutes!
@artswanson53013 жыл бұрын
Just so you know. Your pointy screw driver is a #1 Phillips and the blunt one is a #2 Phillips.
@timvanasen67113 жыл бұрын
Thank's Bob very informative & helpful 👍
@DEMENTEGLOCK3 жыл бұрын
Thank you Bob ! Great doing business with you and looking forward to get more stuff for my grand hauler!! 🙏🏼👍🏼
@js79163 жыл бұрын
Awesome video Bob! Thank you!
@nigeltrafford-jones55697 ай бұрын
just done mine - many thanks
@smartass23t3 жыл бұрын
I use the spectrum radio for my big rig and anything that needs a 3 position toggle switch for shifting gears, etc. Glad I went with spectrum because my particular model has a switch on the back of the radio that can switch from mode 1 or 2, and spring loaded or not. So convenient but it definitely costs a bit more than this radio. Have you ever owned the taigen tanks? I have one but the radio they include feels cheap/toy like. I would love to install a hobby grade radio but not sure how to do it. Need a pcm radio but unsure where to start. If you have any taigen tanks I'd love to see a video tutorial on how to do this. You make great, easy to follow directions!
@rudyackerman57473 жыл бұрын
With "Most" of the newer Taigen tanks, the radio AND receiver can be replaced with most standard RC Hobby radio's.
@cgdoublezerorc3 жыл бұрын
I was thinkin' the same thing as he's doing this install. I'm so glad all I have to do is flip the radio over & mover the switch & then recalibrate.
@michaelchristianson31793 жыл бұрын
I love this radio.
@lasersbee Жыл бұрын
1:26... FYI Bob... They are called Philips Screw drivers.. A Large and a small...
@davidede67215 ай бұрын
Good morning. Thank you for that. Very helpful. But May I ask if it then necessary to alter the electronics so that the centre Position will be neutral . I ask because the throttle mode has the neutral at the bottom setting of the Joystick. I should say that my set is the less fancy fs14. Thank you. Regards David Ede
@HobbyconceptsLLC5 ай бұрын
No, the electronics do not need to be altered.
@craiglunn4237 Жыл бұрын
Hi there Are theses rc plane transmitters your using for your rc trucks?
@topbanana40133 жыл бұрын
very good done thank you very much got my controller today all done. subbed . will say it works both sides i was worried i had to do other stick and was thinking they was sided parts, there not
@joolstacho811415 күн бұрын
Helpful vid. BUT... couldn't you just swap the complete stick assemblies over side to side? You've ended up with both sticks centreing I just want the left (throttle) stick centreing instead of the right. I'll try... Cheers. The link to the kit tells us they're on holiday... Hahaha! Lucky duckys! That's no help.
@CarlosGutierrez-ou2bb Жыл бұрын
just a quick question. in a ship model can the stick stay in the position you place it in so you do not have to hold the stick in the direction of travel continiously.
@HobbyconceptsLLC Жыл бұрын
That would be the way the standard radio is set up. The stick stays where you put it. In reality I find it hard to run boats that way and like the self-centering.
@foxhoundra64442 жыл бұрын
Hello, I would like to purchase an FS-i6 with both returning sticks for my RC car. The link provided is broken for the DIY centering kit
@HobbyconceptsLLC2 жыл бұрын
Here is a link: hobbyconcepts.net/products/flysky-radio-throttle-stick-centering-kit?_pos=1&_sid=efbf31681&_ss=r
@boostjunkieMike Жыл бұрын
Thanks for sharing
@patrickessel35972 жыл бұрын
Thanks 🙏 Buh please no programming needed?
@HobbyconceptsLLC2 жыл бұрын
Yes, you do need to program it. See my video on the Flysky-MFC
@traviswong36862 жыл бұрын
Hi bob very helpful video does the conversion kit work for fly sky i6x ? Thank you
@HobbyconceptsLLC2 жыл бұрын
Yes.
@TheBaconKing323 ай бұрын
Do you think it is possible to remove the spring from the other axis on that stick to make both not recenter?
@HobbyconceptsLLC3 ай бұрын
If you remove the spring the channel won't re-center. Can't imagine why you would want to do that though...
@adewahyuramdhani982 жыл бұрын
thankyou so much
@rayfredette81793 жыл бұрын
great videos well done
@CarlosGutierrez-ou2bb Жыл бұрын
hi again. what is the throttle on feature?
@Funkymojo752 жыл бұрын
Great video. Will the centering kit work on the steering stick as well? Thanks.
@HobbyconceptsLLC2 жыл бұрын
Steering stick is already self centering.
@Funkymojo752 жыл бұрын
@@HobbyconceptsLLC thanks for the reply. Much appreciated...
@kirkabbott2288 Жыл бұрын
Question and thank you for this video okay is it also possible to use the right side of the controller one being I’m right handed and it’s all right centered I already ordered the part but is it possible
@HobbyconceptsLLC Жыл бұрын
Yes, easy. Just plug throttle into channel 2.
@chrislajeunesse1966 Жыл бұрын
So how do I program it so that the center is the neutral zone now and the radio doesn't freak out and say that everything's not centered and asking me to put the throttle all the way down
@HobbyconceptsLLC Жыл бұрын
Can't. The radio will always yell at you when you turn it on with the stick centering option.
@RonaldVassalloАй бұрын
Hi there Bob I just wanted to know if you ship your product to Canada
@HobbyconceptsLLCАй бұрын
I only ship in the U.S.
@mattiasrc3 жыл бұрын
Is a self centering stick a must or is it just for making it easier to drive it? Have a upcoming King Hauler build that im collection electronics for.
@HobbyconceptsLLC3 жыл бұрын
It is a must!
@mattiasrc3 жыл бұрын
Thanks for the answer, then i will get the self centrering kit .
@zibobman2 жыл бұрын
I have a prob with this radio, I can’t enter the menu anymore to calibrate the sticks, even if I put the sticks to the left and turn on the radio, it will stay on the main screen.., Any ideas???
@HobbyconceptsLLC2 жыл бұрын
Try setting the throttle trim down then moving the throttle stick down.
@zibobman2 жыл бұрын
@@HobbyconceptsLLC ok thanks will try it,
@JimBuschman2 жыл бұрын
Very helpful! thank you!
@santosrolon89973 жыл бұрын
Thank you bob you are the best
@virtual_livilng2 жыл бұрын
Thanks for the video; informative
@hjorleifuringason2778 Жыл бұрын
HI, is it possible to order this outside of the US? I only get the option of selecting USA in the ordering link
@HobbyconceptsLLC Жыл бұрын
You should be able to buy that radio and centering kit in Europe.
@thesimpleliving3322 жыл бұрын
how did you get colorful box for this ? mine came in white color. is it fake ?
@HobbyconceptsLLC2 жыл бұрын
That is another style box they use and is not a problem.
@kevintetlow20893 жыл бұрын
Bob how can you get one of the central kits in the UK because I can’t find it
@lucatirino2455 Жыл бұрын
Sei molto bravo 👏 👌🤝💪🏻😉
@perleymccleary97533 жыл бұрын
Hi Bob, I have an FS-i6X radio and I'm having a tough time finding a centring kit. Is there a universal kit? Thx
@HobbyconceptsLLC3 жыл бұрын
Uses the same kit as the FS-i6. hobbyconcepts.net/products/flysky-radio-throttle-stick-centering-kit?_pos=4&_sid=ef0f9db1a&_ss=r At the moment I out this I am out but will be back in stock soon.
@jaburrow002 жыл бұрын
@@HobbyconceptsLLC Hi Bob. Similar question, will the same kit work with the FS-T6 Transmitter?
@carloshnunez3 жыл бұрын
Good upgrade
@Antwilliams197411 ай бұрын
Hi will this work with the tamiya Hornet or thunder dragon etc
@HobbyconceptsLLC11 ай бұрын
Will work with any RC vehicle if you want a stick radio.
@thegooserider72453 жыл бұрын
What receiver do you use
@DavidGonzalez-xk9br5 ай бұрын
I lost the paper to program for trucks where can I get a duplicate
@HobbyconceptsLLC5 ай бұрын
Just email me for a copy. My email is in all the video descriptions.
@patricklavoie87192 жыл бұрын
Are the FS-iA10B or FS-iA6B receivers waterproof?
@HobbyconceptsLLC2 жыл бұрын
No.
@patricklavoie87192 жыл бұрын
@@HobbyconceptsLLC Thanks!
@johnmarkoski68952 жыл бұрын
where do you get the kit to mod the radio for truck mod
I cannot see properly where you put the retainer. It's too dark
@kiterasukabe033 жыл бұрын
Can use for flysky i6X ?
@HobbyconceptsLLC3 жыл бұрын
Same centering kit fits the i6x
@raykerr57173 жыл бұрын
Wish you where shipping to Canada 🇨🇦
@HobbyconceptsLLC3 жыл бұрын
As soon as you mail and customs department start working again I will!
@raykerr57173 жыл бұрын
@@HobbyconceptsLLC it’s all working. Had a order from Amain Hobbies come through this week. I prefer to support the smaller guys like you. 🙂👍 Hope you get sorted out soon. 👍👍
@guywilliamson40743 жыл бұрын
Can’t see what you did
@marktitford48473 жыл бұрын
Wouldn't be so bad if you could see half of what he was doing. Just drop this black bit onto this black bit 🤦♂️
@fccmbc8710 ай бұрын
great videos and turtorials, my question is will this centering stick kit works with the Flysky FS-i10 radio which i have and if it does then i will l order it. Hope to hear from you and thank you.
@HobbyconceptsLLC6 ай бұрын
Yes it works new video: kzbin.info/www/bejne/bXK4mY17d8Zng7s