How to replace Fuel pump in 2004 F250. Thanks for watching!
Пікірлер: 38
@davideide778Ай бұрын
Great video. I used your techniques to replace the pump only on the pump assembly and put my truck co back on the road. The box on my truck is rusted out, so I ended up cutting an access opening to remove the pump assembly. Good job on the video and explanation to disassemble the pump and sending unit. Keep up the good work.
@edgardomatos7742 Жыл бұрын
Absolutely impressive. I just wish i had the weather . 😩. North jersey is pretty cold 🥶. But you have me thinking sliding the bed back , instead of dropping the whole tank ...just seen another video , and he dropped the tank . Watching you do it , seem much more sense by sliding the bed back . Thank you for making this video , very well explained 👏
@kenttaberillinois62023 жыл бұрын
Nobody else showed how it unclipped thanks man
@aarongoodwin48452 жыл бұрын
You can put a couple 4x4 posts between the bed and the frame and then slide the bed! That's if you don't have 4 guys to lift it!
@howardbiel19582 жыл бұрын
He says the most crucial part was lifting the bed off… Then cuts that part out of the video.😂
@clemented10293 жыл бұрын
good video ! big help thanks
@1PaJoe4 ай бұрын
Just cut a panel out from the bed of the truck over the fuel pump - a lot easier than removing the tank or moving the bed as shown
@Axeman2978 ай бұрын
Thanks Great video
@angelaracino62362 жыл бұрын
Thank you I found a video helpful God bless you and your family
@markdevito3592 Жыл бұрын
This guys smart will he come change mine good video
@Axeman2978 ай бұрын
Used a Delphi FEO485 for a direct fit replacement. No pigtail needed (CFE0485)
@IISR9II2 жыл бұрын
Thanks, I have to do my 2003 SD F250 soon. I'll be doing it the same way
@markdevito3592 Жыл бұрын
After you get yours done will you come help me
@jackflackatari10 күн бұрын
What size Torq plus but size is it
@kosmickev2172 жыл бұрын
Did your bed have any rusted slates & if so did you have a problem when you put the bed back on?
@columbiasouthcarolinalifestyle2 жыл бұрын
awesome video
@davidpetrus1748 Жыл бұрын
if your bed bolts are not that crusty then unbolt then ues a floor jack with a 2x4 to tip bed up to pull pump one man job be careful cause when you jack it up it will slide tword the passenger side till the wheel well hits tire then your all set
@22rbz3 жыл бұрын
What’s the part# you used ?
@jamesmontgomery94642 жыл бұрын
what if you have dual tanks?
@leatherguru89043 жыл бұрын
Wasn't there a new sock in the box?
@brucestovall87411 ай бұрын
Why do some people say their no fuel pump inside the tank of a 2004 f250
@mattjones54498 ай бұрын
Because some models don't have the second pump, just a fuel level sending unit in the tank. And the secondary pump (The Primary on some trucks) is the main. I think it depends on your year of 6.0
@wyatt.86363 жыл бұрын
What’s size torqs bit
@markthomas35912 жыл бұрын
T50 fit my F250 bed bolts. Haven't tried a Torx Plus bit.
@LoneWolfSnowplowing2 жыл бұрын
TP45
@privatepilot71812 жыл бұрын
I would recommend dropping the fuel tank over removing the bed.
@enriquepina9417 Жыл бұрын
I am thinking of replacing my fuel pump and I saw your post. Just a question, what are the diffrences in doing it drop tank vs bed removal? I just want to do the job the best way. Thank you in advance for reading this.
@slammed_stangaz3608 Жыл бұрын
I'd also recommend just dropping the tank it isn't that hard
@hnkml123 жыл бұрын
Is it gas or diesel truck?
@wisementrading3 жыл бұрын
Gas
@ferretwithagun9886 Жыл бұрын
Diesel has the hfcm that has been a thorn in my side for the past 2 weeks
@Joe-qv7jk8 ай бұрын
It’s a Geisel
@randalln.5876 ай бұрын
My 7.3 is electric on frame rail. 6.0 should be same. Worked on 05 6.0 was on frame rail with filter cartridge more forward of my 7.3 pump. Never seen this unless a gasser.
@joevaldez29392 жыл бұрын
Why wouldn't you pressure wash and sanitize the area before opening up the tank to all the dirt? Not very smart but good job other wise
@andrewscott98633 жыл бұрын
so if somthing is hard might want to show how u did it thumbs down for this one
@richardhanks83222 жыл бұрын
No
@Mancamp1000 Жыл бұрын
Fuel filter? Around here voids the warranty on the fuel pump especially if you're just buying the motor and not the whole assembly little hint especially when returning a faulty motor make sure you have your receipt or it's on record on the computer and bring in that old fuel filter trust me and your ID don't forget your ID and the bag on the motor I didn't see a new bag sir? When you realize it's not your fuel pump refer to replacing the relay some idiot at Ford put a non-serviceable relay within the fuse block it can be quite frustrating especially when you're looking for a fuel pump driver and your f250 2004 doesn't have a fuel pump driver and all the schematics they give you are different fuse boxes 400,000 miles three fuel pumps one guy never pulled the bed up do it the old fashioned way yes you might get a little gas on you but it's a better way of cleaning the inside of your tank and you got to love brittle plastic thank you Ford oh thank you where is this world going cheap plastic parts oh well happy trucking
@Mancamp1000 Жыл бұрын
Oh I forgot when playing Michelangelo always wear safety goggles a little bit of that grit in your eyeball will cost you about three times the price of that motor at the eye doctor just a little heads up I mean eyes up LOL