ford clutch push rod repair part 2

  Рет қаралды 64,937

Garretts Garbage Garage

Garretts Garbage Garage

Күн бұрын

Пікірлер: 36
@awh5773
@awh5773 4 жыл бұрын
1987-1991 ( brick nose) use the same clutch rod and clutch brake pedal assembly. i have a 1988 f250 custom extended cab long bed with the big zf-s5 trans, this fix works great for me, i also did the firewall clutch repair bracket as well. my clutch is now solid, works better than new. p.s. do the clutch safety switch delete. its just one more thing to to break down on you, (just my opinion)
@patriciareynolds2729
@patriciareynolds2729 3 жыл бұрын
the plastic bushing on the swingarm also wears out and drops, i miked the bushing and ordered a copper bushing amazon, tightened bushing inside hanger behind splines. easier than removing entire swingarm, but brake bushing/pedal is on other end. best might be to pull entire swingarm and weld/bushing/ rebuild entirely after taking out the seat. ha-ha-ha- FORD fix-or-repair-daily!!!!!!!!!!!!
@georgelasala6588
@georgelasala6588 3 жыл бұрын
were can i get one
@Craptastic760
@Craptastic760 4 жыл бұрын
The Ford truck clutch pedal to master cylinder linkage was designed by Satan himself. That cheezy little plastic bushing/clip pops out almost immediately every time I have installed a new master/slave system, which has been a lot of times. I have found that Harbor Freight wire-tie pliers and 0.041 wire can make for a wire loop around the plastic clip that keeps it from popping off. It appears to be the only way to fix this issue without having to resort to the heim joint, which I'm sure is a better solution.
@michaelthornton9016
@michaelthornton9016 7 жыл бұрын
I'm working on a 94 cab but the frame and trans is 87 with my clutch pedal all the way up my master rod is still 1/4 will that have an effect with clutch
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 7 жыл бұрын
Michael Thornton can you adjust the length of the rod
@michaelthornton9016
@michaelthornton9016 7 жыл бұрын
Weaver Repairs no it don't have adjustable rod
@michaelthornton9016
@michaelthornton9016 7 жыл бұрын
with pedal disconnected it sits on rubber stopper with pedal connected has 1/4 space from pedal and rubber stopper
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 7 жыл бұрын
I remember mine had a little play on the pedal. If you can shift into all gears properly then you should be fine.
@keithfavorite9703
@keithfavorite9703 6 жыл бұрын
Can you tell me what the size of that hime joint is?
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 6 жыл бұрын
keith Favorite I'm not sure. I don't have the truck anymore but it looks like a 3/8's hole. If you pull the pin then you could measure it or go to your local farm supply store and get one that's way stronger.
@kwameoseiahenkoraful
@kwameoseiahenkoraful 5 жыл бұрын
I can not even hear a word from this man
@chriscornett9998
@chriscornett9998 9 жыл бұрын
mine on my 94 f250 is the same way. what all exactly do i need to repair mine? any info will be greatly appreciated. thanks
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 9 жыл бұрын
m.ebay.com/itm/like/261916068931?lpid=82&chn=ps&ul_ref=http%253A%252F%252Frover.ebay.com%252Frover%252F1%252F711-117182-37290-0%252F2%253Fmtid%253D1588%2526kwid%253D1%2526crlp%253D53601919689_324272%2526itemid%253D261916068931%2526targetid%253D87946132209%2526rpc%253D0.23%2526rpc_upld_id%253D50676%2526rlsatarget%253D%2526device%253Dm%2526mpre%253Dhttp%25253A%25252F%25252Fwww.ebay.com%25252Fitm%25252Flike%25252F261916068931%25253Flpid%25253D82%252526chn%25253Dps%2526adtype%253Dpla%2526gclid%253DCjwKEAjw4-SrBRDP483GvreDr2ASJAD5sCIuwsu_-aoxNHAcg_YGzQVqSLTVjUapUQYrdoTvkEYohRoCxm7w_wcB%2526srcrot%253D711-117182-37290-0%2526rvr_id%253D847183621134&ul_ref=http%3A%2F%2Frover.ebay.com%2Frover%2F1%2F711-117182-37290-0%2F2%3Fmtid%3D1588%26kwid%3D1%26crlp%3D53601919689_324272%26itemid%3D261916068931%26targetid%3D87946132209%26rpc%3D0.23%26rpc_upld_id%3D50676%26rlsatarget%3D%26device%3Dm%26mpre%3Dhttp%253A%252F%252Fwww.ebay.com%252Fitm%252Flike%252F261916068931%253Flpid%253D82%2526chn%253Dps%26adtype%3Dpla%26gclid%3DCjwKEAjw4-SrBRDP483GvreDr2ASJAD5sCIuwsu_-aoxNHAcg_YGzQVqSLTVjUapUQYrdoTvkEYohRoCxm7w_wcB%26srcrot%3D711-117182-37290-0%26rvr_id%3D847183621134&_mwBanner=1 Here's the link. I cut the rod a little to short but it still worked good
@chriscornett9998
@chriscornett9998 9 жыл бұрын
thanks man
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 9 жыл бұрын
Chris Cornett No problem. Let me know how it went
@chriscornett9998
@chriscornett9998 9 жыл бұрын
alrighty. will do. it grinds real bad in reverse and when im down shifting it grinds real bad in 3rd
@ralphvaccaro2638
@ralphvaccaro2638 6 жыл бұрын
Good job thinking about getting a 1995 f150
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 6 жыл бұрын
Yup. Thanks It worked
@peytonmurray3593
@peytonmurray3593 7 жыл бұрын
Does anyone know if this works on the 2001 F250?
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 7 жыл бұрын
peyton murray I did this on my f250. Ford used the same system for the smaller V8 trucks as well.
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 7 жыл бұрын
peyton murray check your assembly. I'm not sure if it changes with the different body style.
@calebdoner
@calebdoner 4 жыл бұрын
Caused me pain to see you banging on your truck bed to try to knock that pin out. Nice fix though! Looks like this is what I need to do.
@mikeknotts9747
@mikeknotts9747 4 жыл бұрын
I see this over and over again miss diagnosis and Miss fix this is not the correct way to repair this you don't start by taking apart a linkage on one side drilling a hole through it putting a pin in it not fixing the Bind that's on that ran by the way cuz it's going to be at an angle if it's needing an extension obviously it's at an angle so how is the seal on a hydraulic clutch getting a proper straight back and forward push when you're doing that to it. Proper fix is where the problem is coming from if you look to the left side of your clutch you're going to see it on the pedal assembly that the white bushings have gone out on that truck it's pushing your pedal in causing the entire assembly to turn to the right popping off your linkage if you fix that you will not have to do this it only cost two bucks
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 4 жыл бұрын
While i understand you not being there to help or diagnose gives you a complete understanding of the situation, I'm going to say you are wrong. The pedal arm bushings were not worn, the pin was worn and the end of the rod was ovaled from over 20 years of pushing a clutch. The clutch in the diesel was much heavier than that of a gas truck, but for had used the same rod and pin in the different platforms. Thanks for your input, but it's wrong and my solution fixed the issue.
@mikeknotts9747
@mikeknotts9747 4 жыл бұрын
@@garrettsgarbagegarage7970 we didn't insult but you are incorrect in saying that the pressure plate is adding more tension because it's stronger today than it was back in 89. That's foolish it's hydraulic it has nothing to do with the pedal your misinformation is being spread out there like it's fact
@doccrane3143
@doccrane3143 5 жыл бұрын
Dang dude can you find a less clangly work bench next time. Killing my ears !!!
@wooley667788
@wooley667788 8 жыл бұрын
Vice gips -go to tool.
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 8 жыл бұрын
hell yea man
@jakjk41
@jakjk41 8 жыл бұрын
great stuff helpfull 300 dollars Ford lol
@aaronjaben7913
@aaronjaben7913 7 жыл бұрын
2:03
@garrettsgarbagegarage7970
@garrettsgarbagegarage7970 7 жыл бұрын
Aaron Jaben you like that burp. lol
OBS F-Series:How To Do The Heim Joint Clutch Rod Fix
8:30
The F-Series
Рет қаралды 18 М.
ford clutch push rod repair part 3
9:05
Garretts Garbage Garage
Рет қаралды 44 М.
Players vs Pitch 🤯
00:26
LE FOOT EN VIDÉO
Рет қаралды 123 МЛН
Amazing remote control#devil  #lilith #funny #shorts
00:30
Devil Lilith
Рет қаралды 15 МЛН
Who's spending her birthday with Harley Quinn on halloween?#Harley Quinn #joker
01:00
Harley Quinn with the Joker
Рет қаралды 23 МЛН
ford clutch push rod repair part 1
13:25
Garretts Garbage Garage
Рет қаралды 71 М.
Changing a Clutch, 1995 Ford F-150 XL Part 1
12:19
JoeandZachSurvival
Рет қаралды 138 М.
How To Bleed A Hydraulic Clutch - Wrenchin' Up
5:44
Wrenchin' Up with Jim Bates
Рет қаралды 1,4 МЛН
Suspension System Components
13:44
Vehicle Engineering
Рет қаралды 1,9 МЛН
CLUTCH PEDAL FIX FOR FORD TRUCKS
6:29
powerstrokehelp
Рет қаралды 472 М.
How to do a Complete Brake Flush and Bleed
12:53
ChrisFix
Рет қаралды 11 МЛН
Rear Brake Caliper Piston Rewind - With and Without Special Tools
6:38
ScrewsNutsAndBolts
Рет қаралды 603 М.
Players vs Pitch 🤯
00:26
LE FOOT EN VIDÉO
Рет қаралды 123 МЛН