FORD FOCUS MK3 PART 1 ACTIVE CITY STOP NOT AVAILABLE & HILL START ASSIST NOT AVAILABLE ABS CEL ON

[@anguse207]

Hey Enzo, thanks very much for this! Nice dog, what a good boy :)

[@OtakuNoCat]

Did you end up replacing anything? And did the light go off?

[@OtakuNoCat]

Well?

[@tebogoraphiri5873]

hi i have similar issue mine shows "active city stop not available" and " service engine now" then the car goes on limp- mode. Just fitted a new gearbox and new clutch kit, on the car it still does the same. what could be the issue? and oh! i also remapped the car to stage 1, please advise...

[@jonasguinhawa6001]

Hi, bought the ELM327 but unfortunately my computer has no CD-Rom. Do you know which site I can download the installer? Thank you

[@brook3518]

Can the active city stop and auto parking assist be removed forever? I mean I dont really use them daily so just remove it , is it possible?

[@emojim7136]

Hey KL. So another great helpful video. If you remember i asked you about the Lidar Radar I think last week. So i did figure it out that it does operate the Active City Stop option. Now I'm wondering if you can help me out by finding out what in the body control module i would have to activate to make it work. I found a line in FoCCCus that says City Safety. So i enabled that line and then i went into the instrument cluster and enabled it there so i have the option to tick the box to turn it on or off. But i get the message just like you did saying Active City Stop Not Available. But that is the only message i get. All of my ABS and Hill Start Assist work ok. If you help me out and find info on this i would appreciate it. Tnx

[@bosalem2330]

I have such a message, my F150 is the solution

[@mrfaiz4309]

can we use any obd2 reader? can u recommend obd2 reader, i tried to find one like yours but can't find it anywhere. i dont have experienced yet doing diagnostic by myself.

[@klenzo8543]

Yes you can use any cheap $10 elm327 cable but make sure it has a ms/hs switch

[@dans8942]

First Ford focus. Transmission failure, had a friend reset or something like that with diagnostic kit. Worked OK for a while and the problem come back second Ford focus . Auto stop start issues. inactive. Has been for about a year. How do I fix this

[@klenzo8543]

Transmission failure most the cases are a TCM broken. Auto stop start could be the battery under capacity, replace or ask the workshop to measure it first

[@dans8942]

@@klenzo8543 in regards to start stop. When its all turned off it reads 12.1 and when ignition is on its 14.1

[@dans8942]

But thanks for the reply

[@klenzo8543]

@@dans8942 voltage of the batt can not tell the actual of the batt capacity/ how healthy it is, u need to measure a batt cca. Starting the engine is drawn a huge amperes

[@dans8942]

@Simon Mitchell thank you. I will give that a try. That seems it may be right.. when I turn on the ignition 2 turns I wait for all the lights to turn on . The a.s.t comes up green as if its ready . Then 3rd turn to start engine but after that theirs nothing.

[@geniusrafaelus]

Hi KL Enzo. I need help. I'm getting a random DTC, sometimes its there sometimes its not. I also have ABS light and traction control light with error Active city stop and hill assist. Forscan is giving me code U3000 control module and U0415 ABS module..

[@klenzo8543]

Hi Gino, if you're familiar with forscan you can activated your abs sensor left & right on scope menu. While it connected, drive your car and you can monitor the intermittent value on both sensors, my experience one sensor is giving an intermittent value (sometimes zero and sometimes speed value). Check my other video how to use the scope on forscan. U3000, could cause by other things, its a generic info, not specifically abs module. My opinion the changes of the abs/wheel speed sensor is very high. Goodluck mate!!!

[@geniusrafaelus]

@@klenzo8543 thank you. I love your videos. Can I get the digital speedometer using forscan? Or do i need other software? Do you have whatsapp so I can message you? You are super helpful!

[@garyroberts1950]

Can this software be used for re maps or is it just fault diagnostic please ?

[@klenzo8543]

Can't do remapping

[@BohunIC]

great post@!

[@tuansherwynhamidon9687]

Hi Kenzo, can I use any ELM 327 to diagnose and clear this code. Bcz usually cheap ones can just clear engine codes only

[@klenzo8543]

Yes, do able

[@sagittariusz2054]

Thanks I will do that.

[@klenzo8543]

Goodluck then

[@toetiesoeryani377]

How can i instal the program?

[@klenzo8543]

Program is free, forscan.org

[@dennylawhun8214]

1