Ford Fusion A/C quit

  Рет қаралды 196,386

Dan

Dan

Күн бұрын

Пікірлер: 369
@matts.8667
@matts.8667 9 жыл бұрын
Dan the Man, Ford Fusion 2007 Manual temp control AC started cooling and then seemed like heating one day last week, then the next day, NO AC at all, Compressor not even kicking in with an idle down Took it to my mechanic, Freon good, he bypassed relay on engine side, compressor engaged, but not how you did it, then he ran the CPU test, -41 degrees, the sensor is showing, he wants $472.00 including part, the interior temp sensor was $16 at Bennett Auto Supply, but in the mean time, I completed your temp fix, I could not get the clips out, so I pulled back the sheathing and bridged the number 3 and 4 as you instructed, insulated them well with electric tape, put it back together, fired up the fusion and tested the AC and all I can say is THANK YOU. I have the replacement part and will complete the repair per the instructions here, in the mean, I am not sweating my ars off in SFLA (south florida) anymore. The only issue I had was I could not find 47 Kohm x 1/4 Watt resisters, but I found 47 Kohm x 1/2 Watt resisters, will there be an issue?
@nellayema2455
@nellayema2455 3 жыл бұрын
This worked for my 2007 Mercury Milan. I stuck a 47K Ohm 1/2 watt resistor into the blue plug--one leg in along side the 3rd wire and the other leg along side of the 4th wire. The compressor kicked on, and the A/C started blowing ice cold air. The resistors were purchased on Amazon--100 47K 1/2 watt for $5. Thank for the video!
@keithjck4
@keithjck4 9 жыл бұрын
I love the kids in the background and him stopping to handle their issues..Thanks a lot for the info saved many of us a lot of money that we cant afford to spend.
@seamuskelly1464
@seamuskelly1464 7 жыл бұрын
Dan - You are the man. I got the 47k 1/4 w fuse at radio shack for $1 for a 5 pack and followed you video and it worked perfectly. Cold air started blowing right away on my 2006 Ford Fusion SEL. I ended up soldering the resistor because I had a hard time pulling back the clamp. On mine the 13 and 15 pin were not the 3rd and 4th like your example (on mine it was the 2nd and 4th). The slots are numbered in very small characters so I just went by the numbers you said. My car guy quoted me $1,000 so I just saved $999 - thanks!!!
@amt1298
@amt1298 7 жыл бұрын
+Ted Kelly Your welcome.
@lesterpowell8097
@lesterpowell8097 7 жыл бұрын
I have the same car & problem I try this for my A/c
@SteveN-di5fz
@SteveN-di5fz 7 жыл бұрын
thanks! this worked on my 2006. same wire positions, same colors and everything. air is ICE cold now.
@MrFucinbored
@MrFucinbored 9 жыл бұрын
Pulled the dash today replaced evap sensor 3 hours cold a/c feels thanks for the help on the bypass tho i didint wait... good option for the mean time...
@alexberg5189
@alexberg5189 9 жыл бұрын
Thank you so much for this video. My AC stopped working last week and I came across this video, so I gave it a try. Now it works great. Thanks again!
@craigshipley6567
@craigshipley6567 7 жыл бұрын
Thank you, thank you, thank you! Did this and it worked like a charm. $0.04 resistor at Fry's (had to buy a 100-pack) and the cold air is blowing again!
@amt1298
@amt1298 7 жыл бұрын
Now you should repackage the resistors into smaller quantities and sell them on ebay.
@JoeyAmbrose
@JoeyAmbrose 8 жыл бұрын
I used this hack and it worked perfectly. Here are a few observations/notes: 1. Our car is a 2011 Ford Fusion, and there was no wire in #3 slot. I dug through the comments and used +Dan Weston's note below and to find the right wires: "Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector. " 2. To get the wires out of the plug, I used an eyeglass screwdriver I had laying around. 3. Radio shack did not have the resistor, so I got them from my neighbor who is a little nerdy that way. Try an electronics store or get them online if your radio shack doesn't have them. 4. From what my neighbor had, I used 4 transistors to get the right k0hm - a 22, two 22's paralleled, and a 4.7. Luckily me cool neighbor drew me a diagram on how to connect them together. This equaled around 37 k0hm, which for our climate is about right. Thanks again to +Dan Weston for posting this. This was a huge $$ savings. We'll do the real fix using the other cool youtube video when it cools off a little and we have the time.
@NicholasHerndon
@NicholasHerndon 8 жыл бұрын
Hey Joey I have a 2013 so is the same color code for the wires you have the same? And do you have the wiring diagram?
@TimDyb
@TimDyb 8 жыл бұрын
My daughter's 2013 doesn't have the connectors behind the glove box. I looked! Needing help identifying where these connectors are located on a 2013 Fusion.
@jessicabrown6799
@jessicabrown6799 7 жыл бұрын
Tim D k
@yokoobmeasar1037
@yokoobmeasar1037 7 жыл бұрын
Man thank you. It works. I bought everything from Micro Center for less then 20 bucks. I used a 39 omh and it works perfectly. Thank you man you just saved me 300+ bucks.
@jace9062
@jace9062 8 жыл бұрын
Works perfectly! On 2006 Milan. Cold as ICE. Thank you
@amt1298
@amt1298 8 жыл бұрын
Great. Happy tinkering!!
@dallasharris8753
@dallasharris8753 5 жыл бұрын
Jace I got the same year car with the same problem!! Can you point me in the right direction with the right parts (Numbers ) to get and fix mine too? I appreciate the help ! Ty
@spasechuck2997
@spasechuck2997 6 жыл бұрын
Thanks... A 47K-Ohm, 1/2 Watt resistor between 13 and 15 did the trick for me on Fusion without Climate Control.
@kevinmiller346
@kevinmiller346 2 жыл бұрын
i just want to say thank you you bought me time till i can pull the dash
@srvcoldshot
@srvcoldshot 4 жыл бұрын
I pulled my dash last year & changed the evap sensor. Fixed till this year. Won’t pull it again. Started turning the lights & fog lights on. Fixed! For a while. Changed the blend door no change. Trying this next. My mechanic friend says it’s probably a ground problem
@edifice98
@edifice98 9 жыл бұрын
Thanks! Have my AC working again on my 2010 Ford Fusion Hybrid I put the resistor between the Violet/Brown (pin 13) and Gray/Blue (pin 15). Now I just need to put aside some time to fix it properly.
@ohhhwolfy2536
@ohhhwolfy2536 7 жыл бұрын
Thanks so much for the video, Dan! I did this to my '08 Fusion yesterday morning. I soldered my resistor on though because - try as I might - I couldn't get my wiring connector apart and I didn't want to break it. Anyway, not only does my a/c work beautifully again, but my engine idles smoothly like it should. I have a feeling that when the a/c wasn't working right the computer was trying (unsuccessfully) to adjust the idle.
@aaronrendon7957
@aaronrendon7957 3 жыл бұрын
Hola, podrías ayudarme, ¿Qué color de cables lleva la resistencia?
@madjack7979
@madjack7979 Жыл бұрын
Thank you for the video very informative i might try this on the daughters car.
@saifullahpeace
@saifullahpeace 9 ай бұрын
Can you tell which connector is ford ecosport 2013 1 ltr
@JorgeCastillo-lx7uq
@JorgeCastillo-lx7uq 4 жыл бұрын
Just did it to mine 2007 mercury milian , just bought the original sensor and shrink wrap both pins to wires and connect to yellow and purple wires and boom working $30 job
@jawnlaughlin5
@jawnlaughlin5 9 жыл бұрын
Hey thanks Dan that's big help considering the alternative (taking your whole car apart)
@ricapone181
@ricapone181 9 жыл бұрын
Thanks for sharing this video was having this problem in my girls 2007 ford fusion a.c was not working properly cost of new evaporator temp sensor $20 bucks but $600 to get it done at a shop looked at every single way to get to the sensor but couldn't but I tried this used a 33kohm resistor from radio shack $1.59 for a pack of five tried it walla works great.. mechanic said I needed a new compressor !!!. works great and nice cold brisk air feels great thanks.. compressor works fine a.c is cold it was simple 5 mins done... 😆
@tanyaraya2095
@tanyaraya2095 6 жыл бұрын
ricapone181 Do you remember if it was the 3rd and 4th wires from the left, on the 2007?
@OKICUR12
@OKICUR12 5 жыл бұрын
Great works great.My connector on a 2012 uses 13 and 15
@MarioGonzalez-wj9ql
@MarioGonzalez-wj9ql 4 жыл бұрын
For the 2012 it's the 13th and 15th slot?
@homeseverafterllc
@homeseverafterllc 4 жыл бұрын
We have a 2012 Fusion SEL with Auto Climate Control. When I disconnect #15 (blue/gray wire) no air blows at all. Disconnect #13 (violet/brown) doesn't change anything but #15 from under the dash to the connector must be plugged in otherwise there is no air of any kind. Any ideas?
@ronaldhardman2829
@ronaldhardman2829 6 жыл бұрын
I have a 2008 Fusion. Same gray and blue plugs. Is it always the 3rd and 4th pins from the left on top. My third one is yellow like in the video but the third one is a different color. I don't have auto air. I just want to make sure on the pins before connecting the resistor.
@jameschavez3780
@jameschavez3780 2 жыл бұрын
What do you need a. Resistor.? Just to bypass. The evaporator temperature sensor
@amt1298
@amt1298 2 жыл бұрын
That is correct.
@donesquequisieradarte
@donesquequisieradarte Жыл бұрын
Good evening I was wondering if this same process can be applied to a 2014 Ford focus SE if so, does anyone know what pins I have to put in the resistor?
@amt1298
@amt1298 Жыл бұрын
I am sure the same principle will apply and you can get access to the wiring diagrams at the library.
@donesquequisieradarte
@donesquequisieradarte Жыл бұрын
Thanks and might I add my 2012 ford fusion se is still using the same resistor I bought at radio shack over 6 years ago and the a/c is still freezing cold.@@amt1298
@vasb2809
@vasb2809 7 жыл бұрын
Update Ac is ice cold only on max ac setting and i believe its freezing after 10 15 min Just temp control do not work Would you have any suggestion This mkz has dual zone temp control
@russs8446
@russs8446 5 жыл бұрын
What’s the worst that could happen if you do this and never get the permanent sensor fix?
@wingnut2009100
@wingnut2009100 3 жыл бұрын
it will ice up and stop blowing air.
@tanyaraya2095
@tanyaraya2095 6 жыл бұрын
On a 2007 fusion se, will it for sure be the 3rd and 4th wires from the left?
@yhyaalree6661
@yhyaalree6661 Жыл бұрын
Thank you, my brother. I have a question, what is the problem that may cause with the long time (I have a compressor without a clutch)
@robsepulveda681
@robsepulveda681 9 жыл бұрын
Hey Dan, Thanks for the video. I'm having the same problem on a 2012.. Same color blue plug but no wire in the 3rd pin. Do you know what wire I need to tap? to make mine work.
@amt1298
@amt1298 9 жыл бұрын
Rob Sepulveda They changed something...I will need to do some research to find the correct wires.
@robsepulveda681
@robsepulveda681 9 жыл бұрын
please if you can. Dan's the man!
@amt1298
@amt1298 9 жыл бұрын
Rob Sepulveda Does your Fusion have automatic climate control?
@robsepulveda681
@robsepulveda681 9 жыл бұрын
no it doesn't look like it. it has a manuel temperature dial. not digital.
@amt1298
@amt1298 9 жыл бұрын
Rob Sepulveda Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector.
@mariorm89
@mariorm89 8 жыл бұрын
i have a 07 milan with auto climate control, would this work for my car? Also I do not have a check engine code but my a.c. compressor works when power is sent to the plug so i know my issue is not there. it all started when the belt went bad due to a alternator bolt coming loose after the dealer replaced gaskets for timing cover and oil pan, SMH
@brandonbayles9879
@brandonbayles9879 5 жыл бұрын
I’m trying to do this in my 07 fusion sel. It does have climate control. There is no wire in the top left slot then gray blue in second. In the third there is a yellow/purple and fourth is a purple/blue I think. In this system is it still going to be the third and fourth slot regardless of wire color?
@Skam714
@Skam714 9 жыл бұрын
Hey Dan I'm having the hardest time getting the pins out for my 2007 Mercury Milan. It's driving me nuts.
@dallasharris8753
@dallasharris8753 5 жыл бұрын
Skam714 Help.... I have a 2006 Milan with the same problem.
@omarcruz8842
@omarcruz8842 4 жыл бұрын
Awesome, I have a problem on my fusion 2006, can you help me? Poor air flowing out through the vents, the blower motor sounds like working good, but the air flow is too low, like it was blocked.. we know that this model don’t has air filter. A few days ago, the blower began to fail, stopping suddenly for a seconds and then continued working. My problem is the low air flow through the vents.
@allenbraithwaite106
@allenbraithwaite106 6 жыл бұрын
Can anybody tell me in detail where the AC resistor is on aUK Fusion 2005,ivedropped the glove box,and taken off panel in foot well passenger side,not there thanks.
@JohnDoe-cq2hj
@JohnDoe-cq2hj 8 жыл бұрын
my ford fusion 2010 sport ac would start heating. ex. i would get in the car, start car, drive off, turn ac on and it would start cooling from anywhere between 30 secs to 10 mins and somewhere within that time it would start throwing out hot air. not ambient air... HOT AIR! as if it's like i'm calling for heat. the thermostat is on the coldest setting. can you help me out?
@artfisher1235
@artfisher1235 2 жыл бұрын
Is this a fix for air that is cold but not really cold?
@amt1298
@amt1298 2 жыл бұрын
It is not. This is a temporary fix to bypass the Evaporator Temp Sensor until you can get time to replace the sensor or pay to have the sensor replaced.
@TimDyb
@TimDyb 8 жыл бұрын
Need a quick fix for a 2013 Fusion. Same symptoms but there are no connectors behind the glove box like in your great video.
@amt1298
@amt1298 8 жыл бұрын
Very strange. This is a new one on me.
@tomfox2596
@tomfox2596 7 жыл бұрын
'14 Fusion Titanium--a/c pressure reads ~115#--replaced the thermal expansion valve still the same problem. Compressor issue? Other ideas? Thanks--Tom
@amt1298
@amt1298 7 жыл бұрын
+Tom Fox static system pressure is high enough but probably your low pressure switch has gone bad. Firstly, check your fuses and if they are ok then continue. Find the switch on top of the receiver dryer (a vertical can looking item on the low pressure side, large lines) and unplug the connector. Use a jumper wire or paper clip to make the connection between the contacts of the plug. This will bypass the switch in the system when you start the can and turn on the A/C. If the clutch engages, then the switch is bad but if it does not then you have to keep troubleshooting. I am assuming you do not have a multimeter but if you do, checking to see if the switch is open or closed would be the best choice. Let me know what you find.
@tomfox2596
@tomfox2596 7 жыл бұрын
Dan--thanks for the information, but is there a receiver dryer on the Fusion Titanium? I couldn't see it from the top so I put it up on my lift and still couldn't find a canister (I looked at the part on a parts site to be sure of what I was looking for).
@amt1298
@amt1298 7 жыл бұрын
All A/C Systems will have a Receiver dryer (AKA accumulator). From what I can determine, the receiver dryer is just behind the bumper cover and in front of the Radiator and condenser on the RH side of the car. The black plastic cover that goes from the bumper cover to the radiator support will need to be removed to get access to it.
@dbnoho
@dbnoho 5 жыл бұрын
Hey Dan, quick question, why can't a person by an Evap sensor, then splice the wires and feed them into the new sensor, plug them in and then shove the sensor in (or behind) the glove compartment?
@amt1298
@amt1298 5 жыл бұрын
You could but the sensor will cost far more than the resistor.
@teddyblankenship782
@teddyblankenship782 4 жыл бұрын
i must be missing something, there is no sensor in the video? Dont u have to connect the sensor to those wires to replace the defective sensor thats actually in the car?
@amt1298
@amt1298 4 жыл бұрын
Teddy Phoenix What we are doing in the video is fooling the system that there is a good sensor by temporary placing a resistor in the open circuit.
@MrFucinbored
@MrFucinbored 9 жыл бұрын
I didint notice those colors in 13 and 15 would that be the bottom row to the right ? I got the resistors u stated.. ordered the evap sensor as well doesn't seem fun hehe thanks for your time just..harness is blue
@amt1298
@amt1298 9 жыл бұрын
josh damon I have not forgotten about you, just been busy. Hang in there.
@amt1298
@amt1298 9 жыл бұрын
josh damon Do you have Automatic Climate Control?
@dallasharris8753
@dallasharris8753 5 жыл бұрын
What size resister do you use ??
@amt1298
@amt1298 5 жыл бұрын
I used, 47K Ohm 1/4-Watt Carbon Film Resistor (5-Pack) #:2160258, on the temporary fix in this video. The part number is Radio Shack but resistors are available.
@katietriggs1625
@katietriggs1625 2 жыл бұрын
Did this and it worked perfectly. I had to disconnect the battery. When the battery was reconnected, the key was in the on position and the A/C was on with the resistor still in place. Something must have blown because the hack no longer works and the mode actuator doesn't switch from vent to def or floor. I tried doing the fix again nothing. I put the wiring back to original nothing. Checked fuses and relays. Help!
@amt1298
@amt1298 2 жыл бұрын
Do you have automatic climate control? Also, did you check to see if the sensor side of the harness is an open circuit?
@katietriggs1625
@katietriggs1625 2 жыл бұрын
@@amt1298 I do not have auto. I also do not know how to check for an open circuit - or fix that
@amt1298
@amt1298 2 жыл бұрын
@@katietriggs1625 Do you have a multimeter or can barrow one? Also, what year is your Ford Fusion?
@katietriggs1625
@katietriggs1625 2 жыл бұрын
@@amt1298 it's 2012. I have not checked the sensor side. I will have to get a multimeter.
@pmp2559
@pmp2559 5 жыл бұрын
Did this with 2009 fusion now a/c is dead again no cold air, replaced resistor still same
@totaljim2
@totaljim2 8 жыл бұрын
If i'm lazy and just leave this in can it do damage over time or is it okay to just leave it in long term?
@amt1298
@amt1298 8 жыл бұрын
+totaljim2 It will not damage anything but you do run the risk of freezing your evaporator and lessening your fuel milage if you run the a/c all the time but that is just a guess as I have not received any real world verification of that.
@bradleybostaph8260
@bradleybostaph8260 3 жыл бұрын
Is this on an 06?
@MrFucinbored
@MrFucinbored 9 жыл бұрын
What wires do i need for a 2011 fusion seems different then 06 and 2012 thanks wanna try this first
@amt1298
@amt1298 9 жыл бұрын
josh damon Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector. See the diagram in my Google Drive at this link; @0. Left me know if you are having issues and I will dig into the schematics a bit more.
@jdhile02
@jdhile02 4 жыл бұрын
Dan Weston I’m messing with a 2011 Fusion Sport. Would the wiring be any different??
@MrFucinbored
@MrFucinbored 4 жыл бұрын
Jdhile I ended up dropping the dash forward and replacing the ambient air temp senor alot of work for a 15$ part but ac has worked fine since then I didn't me with wires since thats not four tay
@bobmelon9061
@bobmelon9061 8 жыл бұрын
What if your freon were to leak out ? Would the compressor keep ruining and self destruct?
@amt1298
@amt1298 8 жыл бұрын
+bobmelon Good question. The temperature sensor we are bypassing does not control the compressor but rather gives the controller a small piece of information to control the system. Also, there is a pressure switch that must be above a minimum pressure to allow the compressor to run. If the system would develop a leak the compressor would stop running at the minimum pressure. I hope I am not to long winded on this. Happy fixing.
@omarbakhaty6400
@omarbakhaty6400 5 жыл бұрын
Thank you so much. The A/C is working. BUT the compressor does not shut down at all and freeze, any recommendation?
@amt1298
@amt1298 5 жыл бұрын
With a properly charged system, the compressor will continue to run at idle but what is freezing?
@omarbakhaty6400
@omarbakhaty6400 5 жыл бұрын
@@amt1298 thank you for your reply. After the A/C is on for like 30 min, it stop blowing air at all, so i have to turn on the compressor for a while to turn it on again and blow cold air. Do you have an idea what should i do and how i solve the problem? Thank you
@amt1298
@amt1298 5 жыл бұрын
@Omar Bakhaty, The purpose of the evaporator temp sensor is to tell the system when the evaporator has reached temps where the condensation could freeze and so it disengages the compressor. I can only assume you are in a humid climate or it has been raining. If you don't mind, where are you? Can't imagine many people in the US needing AC during the winter except for defroster use at the moment.
@amt1298
@amt1298 5 жыл бұрын
So this is why I classify this as a temporary fix because there is the possibility of freezing over the evaporator, which is what is going on here. Save up money to pay a shop to do it or set aside a weekend to pull the dash and replace the sensor yourself. In the meantime, you will need to continue to turn off the ac every so often to prevent the condensation from freezing or change the temp to add some heat to prevent the freezing condition.
@omarbakhaty6400
@omarbakhaty6400 5 жыл бұрын
@@amt1298 im not currently using the A/C. Im in Ohio, but when i use the defrost and i forger to turn it off it stop blowing air and the windshield become foggier, that is why i was asking if there is any solution for this situation? Thank you Sir
@eoneon7510
@eoneon7510 7 жыл бұрын
I got a 2011 Ford fusion se and my a.c. just gave up and I think it might the sensor ... might this help?
@estradanc19
@estradanc19 4 жыл бұрын
Did it end up working?
@DavidJohnson-is1gv
@DavidJohnson-is1gv 8 жыл бұрын
DanTo check the sensor can I connect the two wires with the resister but not put them back in the clip? Thanks for the great video.
@amt1298
@amt1298 8 жыл бұрын
You could but I still believe this to be a temporary fix to the problem.
@malikara4432
@malikara4432 7 жыл бұрын
Dan Weston....do i unplug the battery
@amt1298
@amt1298 7 жыл бұрын
Sexy Black Stallion If you have the key off then you will be just fine.
@malikara4432
@malikara4432 7 жыл бұрын
thanks ima try it tiday keep you posted👍
@malikara4432
@malikara4432 7 жыл бұрын
lol today...... im excited siting on leather anit cool at all
@MarioGonzalez-wj9ql
@MarioGonzalez-wj9ql 4 жыл бұрын
What tools would I need to complete this? Just the pin and resistor?
@amt1298
@amt1298 4 жыл бұрын
Basic tools but you will need to support the engine if you are taking the transmission out.
@benv9711
@benv9711 6 жыл бұрын
I find it impossible to open the clamps to insert the resistor wires. One does not overlap the other. Another solution?
@amt1298
@amt1298 6 жыл бұрын
you can just insert each side of the resistor into the back of the plug in the proper locations and zip tie into place. You can use quick wire connectors instead and would be a more secure choice. Example: www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=2ahUKEwjwo5Xk7pTcAhWJ6IMKHRoWB08QjRx6BAgBEAU&url=https%3A%2F%2Fwww.walmart.com%2Fip%2F3M-Electrical-540H-Wire-Connectors-16-count%2F17330753&psig=AOvVaw0lAIYLwcZnCO94oo2DhsM8&ust=1531323484942922
@amt1298
@amt1298 6 жыл бұрын
If you use the Quick Wire Connectors, be sure to use meter and check for resistance at the wire locations on the other plug. You are verifying that the Evap Senor is open (∞ resistance) and if the circuit is open then test the system with the resistor temp installed to make sure it fixes the issue. Finally you can go ahead with the Quick Wire Connectors.
@robruble
@robruble 7 жыл бұрын
What site do I bed to go to for buying the resistor? Not having luck finding one
@amt1298
@amt1298 7 жыл бұрын
+Robert Ruble www.radioshack.com/products/radioshack-47k-ohm-1-4-watt-carbon-film-resistor-5-pack
@robruble
@robruble 7 жыл бұрын
Dan Weston ty
@rachelskaggs2578
@rachelskaggs2578 9 жыл бұрын
I'm not completely sure if this is what is wrong with my 2006 Ford Fusion, but yesterday I had the air on full blast, turn the car off to go inside the grocery store, come back out, and the air won't come on. A couple hours later, it randomly came back on as I was driving but then thirty minutes later it cut out again. What do you think it is?
@amt1298
@amt1298 9 жыл бұрын
Taylor Skaggs Is the air not cold or is the blower not running?
@chrishardy9536
@chrishardy9536 9 жыл бұрын
+Dan Weston yes Dan I have a 06 Ford fusion I just watch the video and u say use a 47 but is the watts 1\8
@rachelskaggs2578
@rachelskaggs2578 9 жыл бұрын
its not blowing
@amt1298
@amt1298 9 жыл бұрын
+Chris Hardy I used, 47K Ohm 1/4-Watt Carbon Film Resistor (5-Pack) #:2160258, on the temporary fix in this video. Thank for positing.
@amt1298
@amt1298 9 жыл бұрын
+Taylor Skaggs I would check the fuses first. If it is not blowing air at all then the problem is with the power to the blower, the controls for the blower or the blower motor itself.
@stephanieneafiewest
@stephanieneafiewest 8 жыл бұрын
I have a 2006 3.0L fusion. I have tried using a 33 k resistor for this fix to no avail :( the compressor still will not turn on. Could I need a 37 k resistor or higher or would that not make a difference?
@amt1298
@amt1298 8 жыл бұрын
+Stephanie West It will not make a difference. Does your car have automatic Climate Control (2 knobs vs 3 knobs)?
@stephanieneafiewest
@stephanieneafiewest 8 жыл бұрын
It has a temp knob, a fan control knob and a knob to control which vents it comes out so 3.
@amt1298
@amt1298 8 жыл бұрын
Then you have another issue. Have you checked the basics first? Does the system have a proper charge? Was the compressor cycling more often than normal prior to your issue? If you have a proper charge on the system and it is not running, unplug the low pressure switch and jumper the 2 connections to see if the compressor will turn on. You will need to do some trouble shooting to find the problem.
@zerhghfhf8022
@zerhghfhf8022 7 жыл бұрын
Hey Dan question the blue connector what is it called? Or the silver lead at the end of the wire? I tried to get to it but the wire cut and I need to replace the silver lead. Just can't find it.
@amt1298
@amt1298 7 жыл бұрын
My first thought and easiest, is to go to a salvage yard and remove the pin from another car and cut the wire with plenty of length so you can splice it in. The connector on the wire is crimped on and I am unaware of a proper tool to crimp factory items without deforming it.
@bigrayorozcodavalos
@bigrayorozcodavalos 7 жыл бұрын
hey Dan I tried that quick fix on my wifes 2010 fusion sport and it doesn't seem to work . so I put my head under the dash on the driver side and leave the ac on turn the car off for a few seconds and turn it back on and I can hear some kind of a motor that turns on for a sec. at the same time this is happening the ac blows cold for about 3 to 5 seconds then I hear that motor thing again and it starts blowing really hot air . and all this with in a matter of no more than 10 seconds . any ideas what it can be ?
@amt1298
@amt1298 7 жыл бұрын
Does the AC compressor continue to run?
@bigrayorozcodavalos
@bigrayorozcodavalos 7 жыл бұрын
Dan Weston I believe it might shut off after it automatically switches to heat but then I'm not too sure . not sure where the ac compressor is located in this car
@amt1298
@amt1298 7 жыл бұрын
It appears to me the compressor is just below the Alternator.
@msa_0619
@msa_0619 6 жыл бұрын
Hello There. Yes I would like to know where i can get the right 33Kohm resistor temperature sensor to get my to work on hot mend day in 2011 ford fusion againI live in Houston Tx
@amt1298
@amt1298 6 жыл бұрын
I have just searched eBay or amazon for it.
@twandaye78
@twandaye78 6 жыл бұрын
I thought you said I need a 47K Ohm 1/4-Watt Carbon Film Resistor (5-Pack) (Radio Shack #:2160258)....To do this to a 2011 Ford Fusion SE.....But Michael Shane just asked you about a 33Kohm resistor and you did not correct him, you just answered his question...Now I'm confused... What EXACTLY do I need to buy? Thanks in advance, you're a great man for providing people with this information sir.
@amt1298
@amt1298 6 жыл бұрын
I used a 47K Ohm resistor but mainly you just need some resistance to fool the system. The problem is the Evaporator Sensor is prone to breaking and causing an open circuit. The 47K Ohm resistor was the middle of the temp/resistor range but a resistor with a little more or less resistance with work as well. I still would recommend the 47K Ohm resistor as a temporary fix.
@thisministry
@thisministry 7 жыл бұрын
Hye Dan I only have 12 wires so I'm kinda at wits ends do I count the empty spaces too where there is no pin? Thanks
@amt1298
@amt1298 7 жыл бұрын
If have been busy but I will look at this tomorrow when I get to work.
@thisministry
@thisministry 7 жыл бұрын
Thank you
@amt1298
@amt1298 7 жыл бұрын
each slot in the plug in numbered on the wire side of the plug, if I remember correctly. Also look at the notes copied below. Joey Ambrose wrote; I used this hack and it worked perfectly. Here are a few observations/notes: 1. Our car is a 2011 Ford Fusion, and there was no wire in #3 slot. I dug through the comments and used +Dan Weston's note below and to find the right wires: "Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector. " 2. To get the wires out of the plug, I used an eyeglass screwdriver I had laying around. 3. Radio shack did not have the resistor, so I got them from my neighbor who is a little nerdy that way. Try an electronics store or get them online if your radio shack doesn't have them. 4. From what my neighbor had, I used 4 transistors to get the right k0hm - a 22, two 22's paralleled, and a 4.7. Luckily me cool neighbor drew me a diagram on how to connect them together. This equaled around 37 k0hm, which for our climate is about right. Thanks again to +Dan Weston for posting this. This was a huge $$ savings. We'll do the real fix using the other cool youtube video when it cools off a little and we have the time.
@thisministry
@thisministry 7 жыл бұрын
I only. have 12 wires
@amt1298
@amt1298 7 жыл бұрын
Take a close-up picture of the plugs and email them to me at danielnweston@gmail.com so I can see what you are seeing.
@alialfazani2821
@alialfazani2821 8 жыл бұрын
HI sir my car Hyundai trajet diesel 2.0 cdri and average temperature in my country 28 to 40 Celsius in summer witch resistor i use i mean the number ( 3 . 4 .6 . 8 ) k ohm
@amt1298
@amt1298 8 жыл бұрын
+ali alfzane I will have to do some research on this vehicle in order to provide you with any useful information.
@alialfazani2821
@alialfazani2821 8 жыл бұрын
Ok thank you i am waitting you
@chaddonnelly9604
@chaddonnelly9604 9 жыл бұрын
I installed the resistor and it worked for a week before a fuse blew and now the ac coil is dead. Could this be a result of adding the resistor?
@amt1298
@amt1298 9 жыл бұрын
Chad Donnelly Chad, I am afraid you have multiple issues. The resistor is just fooling the the control module that the temperature is a within range. sounds like you have a bad compressor clutch that is internally shorted.
@thisministry
@thisministry 7 жыл бұрын
Hi Dan I've got a 2010 Mercury Milan after looking behind the glove box to the left plug in harness there is also no third wire will the 13 and 15 pin apply to my car also? Do I have to wait to do this at a certain temperature? Thanks for your help your video is very informative Steve
@amt1298
@amt1298 7 жыл бұрын
Yes it will. These are the same cars with just a few different cosmetic changes.
@thisministry
@thisministry 7 жыл бұрын
Thanks you have helped me with this aggravation twice I have gone to Mountain View Ford Dealership and they keep saying they can't find nothing wrong with the ac. Right! It don't blow cold air just hot every once in a while it blew cold ac and then extremely hot. Thanks again for answering my reply have a good one! Steve
@amt1298
@amt1298 7 жыл бұрын
Your welcome!
@jeffjaruszewicz8277
@jeffjaruszewicz8277 8 жыл бұрын
I have a 2012 fusion se it does not have duel climate it also does not have a wire in the 3 spot is there a way to fix this
@amt1298
@amt1298 8 жыл бұрын
I have not forgotten about you. I have been terribly busy.
@amt1298
@amt1298 8 жыл бұрын
Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector.
@amt1298
@amt1298 8 жыл бұрын
I will but do you have Automatic Climate Control?
@trevlynnespinoza8215
@trevlynnespinoza8215 8 жыл бұрын
Have a 2010 fusion se there's no 3rd wire in the slot which wires would I use to do the resister fix
@amt1298
@amt1298 8 жыл бұрын
A watcher posted a summary that should answer your questions. Joey Ambrose wrote; I used this hack and it worked perfectly. Here are a few observations/notes: 1. Our car is a 2011 Ford Fusion, and there was no wire in #3 slot. I dug through the comments and used +Dan Weston's note below and to find the right wires: "Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector. " 2. To get the wires out of the plug, I used an eyeglass screwdriver I had laying around. 3. Radio shack did not have the resistor, so I got them from my neighbor who is a little nerdy that way. Try an electronics store or get them online if your radio shack doesn't have them. 4. From what my neighbor had, I used 4 transistors to get the right k0hm - a 22, two 22's paralleled, and a 4.7. Luckily me cool neighbor drew me a diagram on how to connect them together. This equaled around 37 k0hm, which for our climate is about right. Thanks again to +Dan Weston for posting this. This was a huge $$ savings. We'll do the real fix using the other cool youtube video when it cools off a little and we have the time.
@ihor43us
@ihor43us 7 жыл бұрын
Hi Dan, thank you for the video and your replies. I read the posts about 2010 Ford Fusions with Automatic Climate Control. No way I can afford to put $600+ out to fix my ac. Symptoms are classic ETS - starts to cool then stops after 2 3- seconds. If I do not use the AutoCC, can this temporary fix work? If not, what stops working - I am in Texas and we need ac.
@amt1298
@amt1298 7 жыл бұрын
I would first check the outside Air Temp Sensor which should be around the RH headlight by the grill. The AutoCC has several temp sensors that work together to control the AC system. The first thing is to figure out which sensor is bad. If you suspect the Evaporator Sensor to be bad then check that by disconnecting the plug behind the Glovebox and make sure it is open. If it is then apply the "Temp Fix" but if it is not then you will need to keep checking the senors until you find the one that is bad. If I remember correctly there is three sensors; inside, outside and evaporator temp sensors.
@sleepsoundzzzzz1234
@sleepsoundzzzzz1234 7 жыл бұрын
Hey Dan, any advice on uncrimping, inserting the resistor and recrimping? Thanks.
@amt1298
@amt1298 7 жыл бұрын
+2Nite2Nite Be gentle. You don't need to get rough with it. I used a pick to remove the pin and open the insulation crimp. Then a small pair of needle nose pliers to gently crimp.
@liridondragusha9467
@liridondragusha9467 7 жыл бұрын
Hey Dan thanks for the video. Can you post a link with the right resistor we can buy, for us that we don't have Radio Shack nearby. A link from Ebay or Amazon would be perfect. Thank you once again!
@amt1298
@amt1298 7 жыл бұрын
+Liridon D www.ebay.com/i/302455865560
@amt1298
@amt1298 7 жыл бұрын
www.ebay.com/sch/i.html?_from=R40&_trksid=p2386202.m570.l1312.R1.TR11.TRC2.A0.H0.X47.TRS1&_nkw=47k+resistor&_sacat=0
@darthvaper9714
@darthvaper9714 7 жыл бұрын
Dan i have a 2011.... is it the 3rd and 4th wire on my model also? Also, where do i get a resistor at? plz reply asap .... its hot!!!!!! thanks
@amt1298
@amt1298 7 жыл бұрын
I will have to search the comments as I do not remember off the top of my head. You can purchase the resistor off ebay, Amazon or a local electronics store.
@amt1298
@amt1298 7 жыл бұрын
Joey Ambrose posted 10 months ago I used this hack and it worked perfectly. Here are a few observations/notes: 1. Our car is a 2011 Ford Fusion, and there was no wire in #3 slot. I dug through the comments and used +Dan Weston's note below and to find the right wires: "Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector. " 2. To get the wires out of the plug, I used an eyeglass screwdriver I had laying around. 3. Radio shack did not have the resistor, so I got them from my neighbor who is a little nerdy that way. Try an electronics store or get them online if your radio shack doesn't have them. 4. From what my neighbor had, I used 4 transistors to get the right k0hm - a 22, two 22's paralleled, and a 4.7. Luckily me cool neighbor drew me a diagram on how to connect them together. This equaled around 37 k0hm, which for our climate is about right. Thanks again to +Dan Weston for posting this. This was a huge $$ savings. We'll do the real fix using the other cool youtube video when it cools off a little and we have the time
@darthvaper9714
@darthvaper9714 7 жыл бұрын
Thanks. I really appreciate it
@ola9765
@ola9765 3 жыл бұрын
Humidity Sensor location?
@amt1298
@amt1298 2 жыл бұрын
I am not sure on that and hope you were able to locate it.
@ernestoegrojga6848
@ernestoegrojga6848 2 жыл бұрын
Its the AC Working good?
@amt1298
@amt1298 2 жыл бұрын
The last I heard it was working just fine.
@jasongittemeier4946
@jasongittemeier4946 5 жыл бұрын
I have a 2011 fusion sport with navigation and the dual climate control. Has anyone tried it and had it work on a model like this?
@allthatihave14
@allthatihave14 4 жыл бұрын
My 06 fan doesnt work right off when i want it, it starts mid ride i live in florida its hot as hell out here i need my ac dont really understand cars but thats a main problem in my vehicle
@shannoncrapse3104
@shannoncrapse3104 7 жыл бұрын
Do you know if you can do anything like this with a 2007 ford 500?
@amt1298
@amt1298 7 жыл бұрын
+Shannon Crapse you should be able to do the same type of temporary fix but I would have to do some research as I have not personally worked on the 500.
@tonycervantes4816
@tonycervantes4816 7 жыл бұрын
Dan where can I buy of resister o resistor and how can I order. Help me out. Thanks
@amt1298
@amt1298 7 жыл бұрын
I had bought the ones I used off ebay. The link below is a quick search for them. www.ebay.com/sch/i.html?_from=R40&_trksid=p2386202.m570.l1312.R1.TR11.TRC2.A0.H0.X47.TRS1&_nkw=47k+resistor&_sacat=0
@tonycervantes4816
@tonycervantes4816 7 жыл бұрын
Ok how many ohms need it . And of resister and of wires from of connector can. I weld it ?? Mi friend Dan
@amt1298
@amt1298 7 жыл бұрын
47k ohm 1/4 watt resistor is fine. I unpinned the wires and opened the insulation crimp of the pin connector. Then placed the resistor in place and gently crimped it. I have seen some people solder it but I prefer my "temporary" approach because you are not permanently modifying anything.
@ericmendoza9305
@ericmendoza9305 7 жыл бұрын
hey Dan, I have a 2006 ford fusion and no air comes out at all, would this trick work for me?
@amt1298
@amt1298 7 жыл бұрын
Afraid not. Check your fuses first for your blower motor, if the fuse is good then check for power at the blower.
@ericmendoza9305
@ericmendoza9305 7 жыл бұрын
Dan Weston I fixed it. I hit the blower motor a few times and it started working again
@amt1298
@amt1298 7 жыл бұрын
That works too! 😀
@jameslockhart5684
@jameslockhart5684 6 жыл бұрын
Hey Dan do you know if this procedure would be the same for a 07 Mercury Milan. Also would it be the same wires 3 and 4. I know the owners manual is the same manual for a 07 Ford Fusion. Thanks for any help you can give me. Great video by the way.
@amt1298
@amt1298 6 жыл бұрын
James, yes it will but the only difference is if the Milan has Automatic Climate control.
@danbass422
@danbass422 4 жыл бұрын
@@amt1298 Dan, what pins for an 07 Milan with Climate Control and what pins for 07 Milan without climate control? Great video, thanks for posting!
@alohann552
@alohann552 9 жыл бұрын
2006 ford fusion CHARGING SYSTEM LIGHT ON BUT IT CHARGING 14.6 ANY CLUE WHERE TO START. PO625 CODE
@amt1298
@amt1298 9 жыл бұрын
Al Ohann The engine control module has detected a fault in the field circuit of the alternator. I would carefully disconnect the plastic plugs on the alternator several times to ensure a good, clean connection. Clear the code, only if P0625 was the only one, and drive. If the code comes back then take the car to an auto parts store to have the charging system checked. Thanks for posting and forgive my delay in reply.
@vasb2809
@vasb2809 7 жыл бұрын
Do you think it would work in the same order on 2012 Lincoln MKZ Hybrid?
@amt1298
@amt1298 7 жыл бұрын
AutoFind Solutions Probably but I would want to look at wiring schematics before I said yes.
@vasb2809
@vasb2809 7 жыл бұрын
Dan Weston the connector looks the same and there is pin 13 and 14 Could you give me a hint i can t find the diagram
@amt1298
@amt1298 7 жыл бұрын
I will look it up today. I hope the schematic is available through my County Library.
@vasb2809
@vasb2809 7 жыл бұрын
Thank you !
@gnomebmw
@gnomebmw 5 жыл бұрын
Hey Dan, on my '09 fusion the clutch engages and the AC light is illuminated, and vent blows warm air. Tried various controls, no effect. Low pressure line in engine bay is not cooling. Could this be the evap temp sensor or something else?
@bradleybostaph8260
@bradleybostaph8260 3 жыл бұрын
What size resistor did u use?
@amt1298
@amt1298 3 жыл бұрын
I used, 47K Ohm 1/4-Watt Carbon Film Resistor (5-Pack) # 2160258, on the temporary fix in this video.
@TripleDouble32
@TripleDouble32 9 жыл бұрын
Hey Dan, I'm not that savvy with cars to answer if my car has automatic climate control or not. Would these steps work for my 2010 Ford Fusion too? Great video by the way.
@amt1298
@amt1298 9 жыл бұрын
phg187 Does your AC control panel have three knobs? Blower Speed on the Left, Temperature in the middle and Air Flow direction on the Right? If It does then you do not have automatic climate control but this will still work for those Fusions as well.
@TripleDouble32
@TripleDouble32 9 жыл бұрын
Dan Weston I have blower speed on the left, temperature on the right, and air flow direction in the middle. Would it be unwise of me to use this technique and keep it like this forever without having it professionally fixed? Thank you very much for your reply.
@amt1298
@amt1298 9 жыл бұрын
phg187 Well you have automatic climate control but the resistor will still work. I will look at the wiring diagram for the automatic climate control and reply as soon as I can. Need to ensure the wires are the same and in the same location.
@amt1298
@amt1298 9 жыл бұрын
phg187 Due to the automatic climate control, this temporary repair is not recommended because the system factors in the the Evap. Sensor resistance to control the components of the automatic climate control and there is not easy way to fool the system with a dummy resistance.
@TripleDouble32
@TripleDouble32 9 жыл бұрын
Dan Weston Thank you very much for all of your responses. I appreciate it very much. EXCELLENT VIDEO!!
@tranquilinocalderon180
@tranquilinocalderon180 6 жыл бұрын
Where do you buy and what kind of resistor is that
@amt1298
@amt1298 6 жыл бұрын
eBay in where I ordered mine.
@gibsonkal
@gibsonkal 6 жыл бұрын
Is there a workaround for a 2014 Fusion? Thx!
@MrLouisianaswagg
@MrLouisianaswagg 5 жыл бұрын
gibsonkal did it work for your fusion
@shannoncrapse3104
@shannoncrapse3104 7 жыл бұрын
Ok would have to figure out which wires to use on it
@Labyrnthdom
@Labyrnthdom 6 жыл бұрын
Ok im confused here. 1. The resistor you have in the video is a 473 ohm resistor according to the color chart. But you said it was a 47Kohm? 2. Also im seeing people in the comments using 33k resistors. So can anyone explain this please? My fusion is a 2008. Not sure if its auto or not. Dont know how to tell.
@amt1298
@amt1298 6 жыл бұрын
I used a 47k resistor but others have has success with using 33k resistors. Mainly you are setting a resistance to the system with function without the Evap Senor as it is a major pain to get to. Sorry if my video was not very clear. It was a spur of the moment thing and I am not the best speaker.
@randy10987
@randy10987 7 жыл бұрын
Will this work on a 2014 se? Which wires would I need to use?
@amt1298
@amt1298 7 жыл бұрын
I will need to look at the wiring diagram for that year to see if there are any changes. I will get back to you as soon as I can.
@randy10987
@randy10987 7 жыл бұрын
Thank you very much.
@amt1298
@amt1298 7 жыл бұрын
My goto for wiring diagrams is currently missing. Looking for another source for information.
@amt1298
@amt1298 7 жыл бұрын
I have not forgotten you. My life has been very crazy this past few week. Please bear with me.
@herb252
@herb252 7 жыл бұрын
I'm also wondering about this, I have the resistor and the wiring digram but I can't decipher it lol.
@avissavage9688
@avissavage9688 8 жыл бұрын
Thank you for this video. I pulled the plug and there is nothing in the 3rd slot just the 4th. Mine is a 2011 ford fusion. Will this work with that model year? Thanks in advance
@calnastic
@calnastic 5 жыл бұрын
Hello have you figured out which slots? thanks!
@MarioGonzalez-wj9ql
@MarioGonzalez-wj9ql 4 жыл бұрын
Did you guys figure which slots?
@donesquequisieradarte
@donesquequisieradarte 7 жыл бұрын
Thanks for the tip it worked on my 2012 Ford fusion the only question I have is is it normal for it to smell like refrigerant when the AC is blowing or does it mean that I need more refrigerant please let me know and thanks in advance.
@amt1298
@amt1298 7 жыл бұрын
+Jose Lopez Does the air smell sweet?
@donesquequisieradarte
@donesquequisieradarte 7 жыл бұрын
Dan Weston good morning Dan sorry for the delay on the reply but no it did not smell sweet and it was only at first now it stopped so just to find out if my AC was calling less I got a thermometer and put it on the vent and I'm getting about 20 to 21° on the thermometer let me know if that's OK thanks.
@MarioGonzalez-wj9ql
@MarioGonzalez-wj9ql 4 жыл бұрын
Which slots did you use for your ford fusion 2012?
@clark6868
@clark6868 7 жыл бұрын
Hey dan I got a 2010 fusion sport do you know which wire I would use on this year and model?
@amt1298
@amt1298 7 жыл бұрын
Another user posted this; I used this hack and it worked perfectly. Here are a few observations/notes: 1. Our car is a 2011 Ford Fusion, and there was no wire in #3 slot. I dug through the comments and used +Dan Weston's note below and to find the right wires: "Well, the wires you need are Violet/Brown (pin 13) and Gray/Blue (pin 15) on the same connector. " 2. To get the wires out of the plug, I used an eyeglass screwdriver I had laying around. 3. Radio shack did not have the resistor, so I got them from my neighbor who is a little nerdy that way. Try an electronics store or get them online if your radio shack doesn't have them. 4. From what my neighbor had, I used 4 transistors to get the right k0hm - a 22, two 22's paralleled, and a 4.7. Luckily me cool neighbor drew me a diagram on how to connect them together. This equaled around 37 k0hm, which for our climate is about right. Thanks again to +Dan Weston for posting this. This was a huge $$ savings. We'll do the real fix using the other cool youtube video when it cools off a little and we have the time.
@coachchristopher3356
@coachchristopher3356 8 жыл бұрын
i have a 2012 Fusion, I just tried this and it did not work. My 14 slot is empty. I used the 13 and 15 slots. My 13 slot is purple but the 15 slot is blue. I used a 33 Ohm resister.
@amt1298
@amt1298 8 жыл бұрын
Do you have automatic Climate Control?
@coachchristopher3356
@coachchristopher3356 8 жыл бұрын
No I don't think so
@amt1298
@amt1298 8 жыл бұрын
Do you have 2 knobs or 3 on the Climate Control Panel?
@coachchristopher3356
@coachchristopher3356 8 жыл бұрын
Only 2 knobs
@amt1298
@amt1298 8 жыл бұрын
Then you have the Automatic Climate Control. there are several temperature sensors in this system. I would start by checking the outside air temperature sensor by the right headlight. Unplug it, then use a mulit-meter to check for an open circuit.
@robotraum
@robotraum 6 жыл бұрын
Got mine to work with this! Thanks!
@hankwilliam2481
@hankwilliam2481 5 жыл бұрын
Thank-you works great
@ashleycruz1632
@ashleycruz1632 8 жыл бұрын
would this work with a 2009 ford fusion ?
@amt1298
@amt1298 8 жыл бұрын
I have not forgotten about you. I have been terribly busy.
@amt1298
@amt1298 8 жыл бұрын
yes. the main factor is whether or not you have automatic climate control or not.
@ashleycruz1632
@ashleycruz1632 8 жыл бұрын
+Dan Weston I don't believe so?? I'm not really sure.....my husband did put the relay in place yesterday. it worked well, BUT this morning it smelled like it was burning some and the fan speed changed....didn't matter what setting I turned the knob to, it was only blowing as if it was turned on the lowest setting.
@amt1298
@amt1298 8 жыл бұрын
sounds like the resistor was placed in the wrong location or something else is going on.
@jonblack4258
@jonblack4258 8 жыл бұрын
Dan so this wont work on an 09 with Automatic Climate Control?
@papitovarona
@papitovarona 7 жыл бұрын
hi Dan, Great video! I'm having the same issue with my 2013 Platinum 2.0 Ecoboost. Do you have another video on these newer models? I REALLY DON'T want to pull the dash!! thanks!
@amt1298
@amt1298 7 жыл бұрын
+Papito Varona I have provided info on 2013 model but maybe not specifically the ecoboost model. Still the system should be the same. I will research if you need additional info.
@papitovarona
@papitovarona 7 жыл бұрын
Dan Weston thanks for the reply Dan. I apologize but t I can 'tseem to find the info for the 2013. I'm pretty sure It should be the same for the exoboost, but I can't seem to find it.
@amt1298
@amt1298 7 жыл бұрын
Papito Varona I will try to look into this tomorrow.
@papitovarona
@papitovarona 7 жыл бұрын
Dan Weston thanks!
@amt1298
@amt1298 7 жыл бұрын
I have not forgotten about you, just crazy life.
@50kristens
@50kristens 4 жыл бұрын
Works!!!!! Thank you so much!!!
@amt1298
@amt1298 4 жыл бұрын
You're welcome!
@amt1298
@amt1298 9 жыл бұрын
Abe Ramirez - You have Automatic Climate Control on your 2010 Fusion SEL and I am afraid there is not a quick temporary fix that I would recommend. The Climate Control uses the Evaporator Temp Sensor to control temperature diverter doors and other components. Not sure what would happen when a fixed resistance is temporarily placed in the circuit. I will need to review the diagrams and think about it.
@th_holy_ghst
@th_holy_ghst 9 жыл бұрын
Just read your reply. Last night I connected the resistor to pin 13 and pin 15. The clutch kicked in and it started blowing cold air. One thing I did notice is since I have dual climate controls it only blew cold on driver side but passenger side only blew out cool/fresh air. Not as cold as driver side but better than having hot air. Hopefully I'm not causing any damage. Plz let me know what you come up w/after review the diagram. Thanks for the reply.
@amt1298
@amt1298 9 жыл бұрын
Abe Ramirez I am trying to figure out what connection (cannon plug) # which you are using. I am still working it but currently I have no idea what you are bypassing in your circuit. I will look at your pictures and try to figure out what connection # it is based on the pin and wire color locations.
@samukasangiorgi
@samukasangiorgi 9 жыл бұрын
Hi dan, whats is the amps of this resistor, please
@amt1298
@amt1298 9 жыл бұрын
+samuel sangiorgi I used, 47K Ohm 1/4-Watt Carbon Film Resistor (5-Pack) #:2160258, on the temporary fix in this video. The amp draw is approximately 0.000255319149 amps. Thank for positing.
@samukasangiorgi
@samukasangiorgi 9 жыл бұрын
+Dan Weston Dan, my fusion is a 2008 I believe the colors of wires are diferentw than yours, can you help me, the compressor works fine when I charge it directly
@tyronelee3867
@tyronelee3867 6 жыл бұрын
Awesome video! I was wondering if this worked for a 2010 Lincoln MKT? And if so, could you provide guidance on which wires?
2011 Ford Fusion - A/C Stops Working
9:30
TightWadProductions
Рет қаралды 78 М.
Ford Fusion AC Evaporator sensor repair bypass fix
7:28
Chris H
Рет қаралды 70 М.
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 54 МЛН
Tuna 🍣 ​⁠@patrickzeinali ​⁠@ChefRush
00:48
albert_cancook
Рет қаралды 131 МЛН
Quando eu quero Sushi (sem desperdiçar) 🍣
00:26
Los Wagners
Рет қаралды 14 МЛН
2010-2012 ford fusion HVAC blower Motor issue
9:47
KadaYah Yisra'el (kadahinton)
Рет қаралды 102 М.
Ford A/C Quick Tips #7: How To Quickly Diagnose A/C Concerns
13:09
FordTechMakuloco
Рет қаралды 1,5 МЛН
Doing This Will Make Your Car's AC Blow Twice as Cold
11:10
Scotty Kilmer
Рет қаралды 2,9 МЛН
DIY Testing, Fixing, & Recharging A/C
18:35
That Shop Teacher Guy
Рет қаралды 675 М.
How to QUICKLY Test A/C Clutch At Home
6:43
CarsNToys
Рет қаралды 179 М.
Ford Fusion blower motor resistor and pigtail replacement
11:09
Michael Tomko
Рет қаралды 9 М.
Ford AC Trouble ! (Variable AC compressor)
31:50
DiagnoseDan
Рет қаралды 383 М.
Things You Should Never Do In An Automatic Car (Big Mistake)
15:08
Car Care Clues
Рет қаралды 803 М.
We Attempted The Impossible 😱
00:54
Topper Guild
Рет қаралды 54 МЛН