Ford F-150 5.4L 3v Triton Engines: This is Why You Always Replace the Roller Followers!

In this video we show you why it is so important to replace the roller followers whenever the engine is opened up for service.
These are the Parts and Kits I Recommend:
2004-2014 Engines Latest Roller Followers x24-
amzn.to/3BtEHgm
2005-2014 Engines can utilize this Ford Racing Kit-
amzn.to/492DRYC
Forscan is a free Ford Specific Diagnostic Software:
Download Here-
forscan.org/home.html
ELM 327 Adapter I Recommend-
amzn.to/2GC6dBj
As an Amazon Associate I earn from qualifying purchases.
My Automotive Repair Shop BSG Automotive-
www.bsgautomotive.com
Catch up with us on-
Facebook: / fordtechmakuloco
Twitter: / fordtechmak
Instagram: / fordtechmakuloco
Disclaimer:
The information, demonstration and any content contained in this video is for informational purposes only. The user and BSG Automotive (hereinafter “FordTechMakuloco”) makes no warranty, express or implied, regarding the effectiveness or safety of the contents of this video. In no way should the contents of the video, including the tools used, be repeated or tried by anyone. Viewers should only seek the help of a trained professional located at a licensed auto repair shop for any fix, modification, alteration, or any change to their vehicle. FordTechMakuloco shall not be liable for any injury, damage, or loss to any person or property that may result from use of the tools, equipment, or any content contained in this video. In addition, there is no way to guarantee that the video is not altered or modified or is not in the final form submitted by FordTechMakuloco and therefore, FordTechMakuloco does not warrant that the video is unaltered or not modified. The links on this video to products are for informational purposes only and in no way are an endorsement of the safety or effectiveness of the particular product. Viewers understand that anything contained in this video or linked to or from this video is the sole responsibility of the viewer and in no way provides an express or implied warranty as to the safety or effectiveness of any linked tool, product, or video. Therefore, viewer agrees to release, waive, and discharge FordTechMakuloco or anyone affiliated with FordTechMakuloco, from any and all liability, claims, demands, actions, and causes of action whatsoever arising out of or related to any loss, damage, or injury, including death, that may be sustained by the viewer, or to any property belonging to viewer, regardless of whether the loss is linked to the use of the contents of this video, or otherwise and regardless of whether such liability arises in tort, contract, strict liability, or otherwise, to the fullest extent allowed by law.

[@FordTechMakuloco]

These are the Parts and Kits I Recommend: 2004-2014 Engines Latest Roller Followers x24- amzn.to/3BtEHgm 2005-2014 Engines can utilize this Ford Racing Kit- amzn.to/492DRYC Forscan is a free Ford Specific Diagnostic Software: Download Here- forscan.org/home.html ELM 327 Adapter I Recommend- amzn.to/2GC6dBj As an Amazon Associate I earn from qualifying purchases.

[@jonmccormick8683]

Get FORScan if you have a Ford/Mazda vehicle. -Best thing you can do.

[@tomedwards3814]

Brian. Could you link all the associated parts for the bullet proof upgrade?? I have a 05 5.4 myself. Thank you Tom

[@bradnoyes7955]

What could cause a light metallic rattle only above 2500 RPM? Ford Lash adjusters, followers, phasers, and solenoids have about 10k on them.

[@MichaelResznekiTrolling4Truth]

Call Simply the Best Towing and Recovery. I'll tow them to ya.

[@codpi1358]

Are the rockers for the two valve the same as the three valve?

[@bsovan]

So this was my truck that I shipped to Brian. 2005 with 122k miles, oil changed religiously every 3k miles alternating between Mobile 1 and Royal Purple. Timing service with OEM Ford parts and HV oil pump was installed 20k prior, I was talked out of doing the rollers at the time by my mechanic. Truck started to progressively go down on power and noise would just get louder. I already invested quite a bit into it and would rather ship it to Brian to fix than buy a new truck. With this fixed I should be good for another 100k easy. 4k for service and round trip transport. Truck runs like NEW, Thank you Brian!!

[@soundmind192]

I can see why you opted for Brian to fix instead of recycling back to original shop. They were ignorant or lazy which cost you more money to go back in and do it right.

[@dchun81]

What kind of headlights are those?

[@waynejones3999]

I'm wanting to know where he is located and how much the total cost was. My wife's 2011 started skipping and I'm afraid that a follower has come off. Truck has about 186,000 miles now.

[@Kodyoti5]

What codes did you have on this?

[@josephmichuda6447]

@@waynejones3999 I think he's near Chicago but I'm not 100% sure.

[@christinaperez254]

And this is why folks bring (or send) their trucks cross-country to Brian (we did from Idaho).…...no stone unturned, thorough and done right. Money well spent.

[@Kanesgarage]

Wow. What did you send it in for? Timing job on a 5.4?

[@chrisjackson9102]

I live in Cali. I do almost all my own maintenance. I have a 10 Ranger 4.0L and a 4.6L Mustang. If either of them need timing jobs, they are getting shipped to Brian. If I need tranny work, it's going to Precision Transmission in TX. Too many hacks around here. Buy once cry once; there is always enough money to do the job right the second time.

[@ttstang43]

@@chrisjackson9102 this is the type of shit that pisses me off as a tech, the hacks in life that give those of us that provide quality and quality service a bad rep, whether the shop or the individual tech.. Makes it harder for the rest of us good ones to get work and make money and make clients a forever deal.. and the last part of your statement will forever be the truth, do it once, cry once and be done... i like how you stated that to.. its pure facts..

[@CooperCarr]

I need a Brian in Dallas Texas. Wish ford did a better job of showing where there certified mechanics are.

[@wagnerfamily4229]

I had this happen on my 2012 Expedition with 65000 miles and it ate 1/4” off of the cam lobe. The Ford house replaced my trans valve body and catalytic converters. An independent repair shop diagnosed the followers and had it done in two days. The Ford house has it over a month.

[@blackscotydog]

You know you're good when you're customer's come half way across the country

[@chrisgraham8711]

do you know where he is located ?

[@blackscotydog]

@@chrisgraham8711 Mid west US I think.

[@Jay388]

Just outside Chicago BSG Automotive

[@brianpomeroy6199]

Yes please do a bulletproof video with all the tips! Thank you, you are a great teacher, love the detailed explanations.

[@guesswhomartin9249]

Yeah, it took me awhile to realize this guy really is a good mechanic. There are a few mechanics on KZbin, they're vieods are very " ifees " . But this guy here, he's right on target, everytime.

[@wealthNwisdom63]

Correction he’s a great mechanic for us Ford F-150 guys

[@celticrunes1911]

@@wealthNwisdom63 Correction again, he’s a great mechanic for ALL things Ford, not just trucks.

[@wealthNwisdom63]

@@celticrunes1911 lol yeah of course but since I have a truck that’s my main concern

[@brucewilson5523]

How can I get in touch with you Brian

[@hella_2350]

If you do the bullet proof video, it should be played mandatory for all the techs at all the Ford shops. Awesome work!

[@ttstang43]

honestly, not just ford even... but all shops period. although this is specifically related to ford but same quality concept for any vehicle.. i say that because i used to be a ford tech but now an independent shop tech..

[@TheNuclearBolton]

@@ttstang43 honestly I have a hard time trusting anyone working on my car because of the techs and mechanics that have screwed me

[@thomasv5596]

What's the bullet proof video

[@tyrannusspissamentum4423]

Exactly why I'm picking up more precision tools to do a full rebuild on my 5.0l I want to do it now but im settling for new timing equipment and followers. Looking a lot of MMR parts.

[@foofyguy]

I had a tapping sound just like that on my 4.6 3v. I tracked it to cyl 5, pulled the cover and inspected everything. I ended up pulling and testing all the rollers and lifters on the driver's side. Nothing was broken. I was fearing a noisy valve so I went to pull the spark plug to put a camera in th cyl to see what th valves and piston top looked like. The spark plug was loose enough I could spin the socket with my fingers. A loose spark plug ended up being the the source of the noise. Lesson of the day, don't forget to start with the easy stuff first. 😩 Anyway, thanks for all the vids FTM.

[@johnbrentonlll]

Easy likely

[@dylanzellers3819]

Definitely do a bullet proofing video of the best things to replace to make sure the motor survives the longest

[@abominabledrphibes2693]

My Philosophy for over 40 years as a backyard Mechanic: Don't go Cheep, and if it's a hard to get to Fix, Replace Everything.

[@guesswhomartin9249]

I agree, don't do cheap. You pay cheap, you will get cheap. You get what you pay for. There's no such thing as a free lunch.

[@tinkerscorner54]

Amen. I hate doing the same repair twice. Especially the hard, tight, knucle scrapers where you have to close your eyes in order to mentally see what you're doing. Right Part, Right repair. Cheap Part, You'll be back there. Later

[@bobbybrown931]

Ford didn't come up with an update for grins they knew there was a problem.

[@rockerpat1085]

I am literally waiting on my customer to pick up their 2010 5.4 3v that dropped a valve!!! I pulled both heads, fresh valve job, NEW ROCKER'S and Lifters!!! Had to Replace the 1-4 Camshaft, torn up due to failed Rocker!!! All New Chains, Tensioners and Sliders!!! New plugs and all Coolant Hoses and Drive Belt!!! Replaced Rear Rotors and Pads!!!! All Cost The Customer 4976.39 Parts and Labor and Tax!!!!! NOW BRING ME MY MONEY!!!! Keep Rocking It Out Brother!!!!!

[@billgelsdorf3075]

If I had a 5.4 and it needed anything Brian would get it I don't care how far I had to truck it, actually any Ford, he is the man!!!!

[@gm1258001]

Definitely says something when folks are shipping their trucks your way for service. Great work!

[@skyloveup]

Where's he based out of?

[@jonmccormick8683]

Notice how small that "new" follower oil hole is = your oil needs to be exceptionally clean to get thru that hole. =Change your oil and filter more than you think you need to do and use a high quality synthetic oil. -And this person changed his oil real well (super clean engine).

[@bsovan]

This is my truck, oil change every 3k miles alternating each time between Mobil 1 and Royal Purple. I would also add a qrt of Lucas added with Miracle Oil . Couple hundred miles before oil change I would add Seafoam in the crankcase.

[@garymcmullin2292]

I have the same concerns about that super small diameter oil hole. I foresee the possibility of tiny bit of some carbon or lint or any other odd ball foreign matter plugging it up and you know what is going to happen then! I even wrote Makuloco about this and considered trying to drill them out. Turns out the steel is hardened and that small a bit would be breaking regularly. Makes it worse that the original hole was done before the roller bearing was installed and the angle cannot be matched now if I did attempt to redrill.

[@nomebear]

The engine was so clean inside, obviously well maintained, then the problem was a bad design.

[@djg1028]

Would love one long 5.4 bullet proof video of all the stuff that needs to be done.

[@michaelmurray121]

Trailering all the way from California to the best of the best Fordtechmakuloco Brian the best of the best love you man I learn a lot from your channel…

[@jonmccormick8683]

Probably $2-4k to ship this to the Chicago metro area. But new trucks are incredibly expensive $50k + if you can even get one.

[@paulsosa1872]

That's crazy that someone had work done to have another problem. Then to have it shipped so far for to have a trusted mechanic diagnose & fix the problem properly. THE IS SAD WE DON'T HAVE LOCAL HONEST SHOPS TO DEPEND ON

[@martinmessineo4964]

Awesome video! I just picked up an '06 F-250 4x4 with the 5.4 3v with 124,000 miles. I was hesitant to buy it because of the failure prone 5.4 but for a largely rust free 4x4 F-250 $5,200 was too good to pass up. I know at some point I'll likely need to bulletproof it and I'm glad to know that such a competent tech is only 90 miles away from me. Keep up the good work and may your 2024 be blessed!

[@greasee.monkey7224]

Working at an independent shop, I still see these quite a bit. Somehow on the last two, the camshaft was unharmed. Lash adjuster & roller follower failure. I work on alot of these engines and have seen some carnage. Thanks for the tips & tricks!👍👍

[@chrisgraham8711]

question, where do you guys order these parts from ? I want to replace my cam shafts and all followers but Brian's link shows they don't fit my 08

[@headgearjoe]

This goes to prove. Old school thought mechanics can listen to an engine along with computer help to find the problem. You can't use just a computer.

[@repeater95]

True

[@shaneanderson1036]

so good to watch a master at work . no bull no if’s no butts ! straight up 100% masters info . loved it . thankyou

[@risenfromyoutubesashesagai6302]

Yes, please make a "Bulletproofing" video for the 5.4 3V Triton. I'm bout to garage mine and prepare it for some heart surgery.

[@transientmwx]

I appreciate your passion and detail in your videos! As for the “bulletproof” 5.4 video”, yes please! Planning to do complete timing job on my 06 5.4 and stoked to see it! Thank you.

[@keepyourbilsteins]

That bulletproofing video would be great! Thanks for the top tip on those followers.

[@dontehoward1554]

I just finished a timing kit rebuild on my 5.4 and i don't even want to get paid to do that same job again

[@HangImHigh]

This shows you the difference i a mechanic and parts changer . Well done my man !

[@MatthewBonacci3881]

Brian thank you so much for giving back to the ford community. Because of your videos I have decided to hold on to my 2006 Ford Expedition 5.4 3v and so the PM to keep it a long time. Look forward to future videos.

[@huntingspud3086]

Another nice and thorough job (as usual). If only all mechanics followed your example, what a gift to customers that would be.

[@Reactor7392]

Apparently, you are a. s. e. certified to be doing these tuning fixes! This video clearly provides what my '08 3V 5.4L has been doing! Thank you for that short result! I, myself desire to "know" how it feel's to be a "master technician" before being labeled one!

[@jafofubar3793]

as a retired Mechanic of 48 years i always used OEM unless Customer wanted different - and honestly when i retired from the field ( even Diesel ) the one Engine i never had or got the chance to Rebuild was the Zero set Static Timed Engines - when those started on the market was about the time i went to Diesel until retirement - any major work like this i would always state to replace all components not just what is wrong or it will be back for service shortly after with more problems -- i would even pull the oil pan on some cases to see if any damage in the bottom half of the engine ( crank shaft , end caps , connecting rods , Main Bearings ) my motto was if its not right it does not leave !!! seen many fast repairs go horribly wrong

[@rayvonp]

I really feel for you man I’m a mechanic out west when I watch your videos on some of the crusty vehicles that come in i cringe and it does make your job that much more harder but you keep at it brother appreciate it and Semper Fi

[@closertothetruth9209]

i love watching guys like you who specialise in one brand, you guys know all the common problems and fixes unlike a genric mexhanic that works on all brands.

[@BD-qq4fn]

Your back has to be made of Iron! I did a full cam follower swap on my 2010 F250 with the v-10 (30 followers) in summer of 2020……my legs were rubber when done….and my back still hurts! Love your videos, immensely helpful for us weekend want-a-be’s.

[@garync3810]

Look into "mechanics high top creeper" if you do much on higher vehicles. Kinda like a ladder with a small ironing board for you to rest your chest on.

[@andrewp8491]

Yes please make the 5.4 3v Bullet Proof video! I've learned so much and have been able to take care of many things myself on my owned since new F150 Lariat SC 4X4. Thanks for all of it!

[@AlphaG33k]

As a guy still driving a 2007 5.4 F150, I would love to see a bulletproofing video.

[@jrumlr]

Man you are just amazing at what you do. Great material.

[@squibbert]

You are the best! Thank you for all high quality videos and great content and knowledge. I'm going to tackle this job when the weather improves.

[@Frank-gv6fs]

Im doing a timing job on my personal vehicle in my spare time, I wasn't going to change to roller because they look good, but now Im going to order all new sets. I already found a loose chain which was starting to eat into the timing cover and timing sprocket I don't want to have to crack open the engine again one time is plenty enough for me.

[@Jbyrd75901]

On my 270k mile 04 I did 05+ cams and 05+ lash adjusters as the 04 cams where $300 each and the 05+ $115. Also did the m340hv and the small hole updated followers. Love the videos.

[@scottcarden8236]

I love your videos. I live in Texas so everything comes apart easy and no rust to deal with. I lived in New Hampshire for years and felt like more of a rust repair man than a mechanic. I own a 2014 EL King Ranch 4x4 that I did a timing set at 120k. I just bought a 2008 EB 2wd. And I bought it cheap with a terrible timing rattle. I have it torn down now and bought the parts with your links, including the oil pump. The odometer reads 220k and two of the guides were completely gone. Some chewing in to the oil pump, case, block, head, crankshaft tone ring, ect, but nothing serious. The engine had all ford parts and the phasers were still good. The drivers side tensioner had come apart. I’m doing all new ford parts including starter, water pump. There is only a small bit of scoring on the passenger side came caps. Only on 2 of them all the others look great, really great for the mileage. All the roller followers looked great and I was going to reuse them until I saw this video. Thanks again for all your great videos and info. I get requests a lot to make videos of some of my repairs and I’m still thinking about it. I have a great fix for electric running boards and a few other quirky things on fords. Maybe one day I’ll get around to posting them.

[@Alpha-1Livewire]

I followed this advice from your older video and got Ford Performance to send me some out of R & D. They were so gorgeous I played with them for a day before installing them 🙄. I bought and installed FP timing and phaser kit $535, Melling HV540 oil pump $140, solenoids $140, lifter/follower kit $285. 2006 Mustang 4.6L. the cams were fine so I reinstalled them. I rev to 7000 with no concern. Don't be cheap. Do it right the first time readers!!

[@edman1015]

FordTech you need to make a training video for the Ford Engineers and get paid from Ford. Get them to rewrite their maintenance manual.

[@edwardbrown5389]

Great info, I have an 04 V-10. In 2013- 150k I heard the startup knock, dealer replaced the rollers, 236k still running great. Thanks again, I was trying to remember what happened, 6-7-8 years ago, now I remember.

[@armandog7051]

Most definitely I will include that on my next timing job I had my truck for 9 yrs almost 300,000 miles and Thank God 🙏 still running like a champ!!! Thanks for all of your videos I learn alot from them. God Bless

[@Pbaglio21]

Very good video my friend, I appreciate your, not only informative videos but your expertise and reasonable prices. You are rare. God Bless You!

[@xTRExDADDYx]

Love the channel man! I just wanted to share a issue I noticed. As others have experienced, what comes up from the link says it does not fit my truck (2006 FX4). I notice that in the when the page comes up, it has the new part number in the search bar at the top, but its bringing up the old part for whatever reason. For anyone else who maybe be scratching their heads over this the way I have been, I'll point out that in reading the reviews people are confirming that despite ordering the old part number they are in fact receiving the revised part.

[@scottisaacson1101]

Brian, all your videos are so well done and extremely helpful....Thanks! Just to clarify, one can replace the rockers arms without replacing the camshaft, as along as the cam is in good condition. Correct?

[@curtesamoangelos5995]

Watching from Yosemite, Kentucky. Great video as always! Thank you for taking the time to share your work and knowledge. I own a 2002 F150 XLT 5.4 4x4. Everything is stock and only have 72K on it. Starting to get a tapping noise on the passenger side of the engine similar as on this video but not as loud. Only when cold but after 7 miles or so almost disappears. Started about 4K miles ago. Hoping it isn't too serious. Again, great video.

[@jerryfrederick6610]

Brian, you are just fantastic in your content. A real gift to all the everyday folks trying to keep their under engineered or dare I say engineered to fail vehicles going. I purchased one of your tee shirts and proudly wear it and am constantly surprised how many people recognize it for your channel. All discussion that follows is Very positive and very grateful. Your candid honest opinion and delivery is very much welcome. Thank you and God Bless

[@markm0000]

Good to see you got a big AC setup to cool down the shop.

[@elparasito2001]

Hey man! I will definitely be waiting for the bulletproof video, thanks!!!

[@jkurzz]

Hoping to start my 07 f150 tomiming job this weekend after I get done doing the brakes on the wife's 07 expedition. I have purchased your amazin kit with all the ford components I think ill be ordering these followers before I put everyhting back together.

[@sandrarichardson2713]

Thanks Brian...hope to do this soon. Trying to watch everything I can on this. Have '06 5.4. Once I watch it enough and study my engine...sooner or later I hit a comfort spot where I'm ready to tackle it. Wish I had another little scoot around car though in case something horrible happens so I'm not stranded. Oh me. Appreciate your help. Jesus bless.

[@altatude9677]

Thanks for all that experience. This is a wealth of knowledge.

[@dmoney4225]

I would love to see a engine rebuild video from Brian. He is so detailed. I’m sure the video would pay for itself with the views. I’ve repaired so much from his videos.

[@andrewfindlay4836]

Fantastic video. Super clear and very helpful and expert advice.

[@Joserocha-wm9de]

I dont own a Ford neither i am a mechanic , i learn and try do do as much as i can but watching a real master mechanic doing its thing its so satisfying .. I love and enjoy watching your videos Mr FordTechMakuloco you are the best 👌👌

[@Bamacher59]

You are the best Ford mechanic!

[@MysteryScienceGaming]

love these videos. About to buy a 5.4 if I get the right price and pretty sure it needs these replaced as well as timing chain.

[@mikewillifordjr]

Very nice, thx for the tips, I just finished a swap on a 07’ w/ 5.4 with a reman, it’s rattling pretty bad, guess I’ll be going in!

[@philipplastina181]

bulletproof video please! I'm so excited to follow your video and update my truck. I just bought a mint 2005 and I want to make it immortal.

[@biz4twobiz463]

awesome awesome video!! Wow, learned so much...and the before and after sound is amazing!! Merci

[@josedejesusvelazquez6863]

Great demonstration of Mastery. what a job dear friend. Greetings from Tijuana 🇲🇽 Mexico

[@baileyhessler6232]

Have you had any rocker arms cause damage to a valve ? If so do you have any videos about that? New subscriber, newer than novice with mechanical understanding. Your videos are extremely in depth and exactly what I’ve been looking for! I’m not confident in fixing something like this myself but it is nice to be able to communicate and understand with the person who will be doing the labor.

[@fanaticofutube]

Love when he does the older 5.4 3v video

[@micheledykeman4255]

Another superb video! Thank you so much for doing these!

[@brucesimpson8579]

Even if all of the transport and repair work cost the guy $4K, it's still cheaper than buying a new truck.

[@jonmccormick8683]

-If you can even find one. California vehicle supply is the worst.

[@obidenwhatajokeverysad5809]

California in general is the worst

[@TwentytenS4B8]

The transport and repair was still significantly less than 7K+ for a new engine.

[@TheBigdog868]

...and I dare say probably better made than anything coming off the line nowadays

[@JimBronson]

@@obidenwhatajokeverysad5809 the people are the problem. The natural geography of the state is beautiful.

[@dewaynebevis5484]

Love to see the water pump job on the Edge. Wife and daughter both have one may have to do one in the future,!

[@sbalak]

THanks for the great video. We need a lot more experts like you everywhere. If you recommend anyone or a general mechanic in AZ (Phoenix or Tucson ) please let us know.

[@squibbert]

You videos are the best. So thorough. Thank you.

[@stevefawcett5507]

Brian, I can't thank you enough for your F150 5.4L 3v videos. I have one question regarding the new design of the roller followers. With the increased back pressure they provide would you still recommend switching to the Melling M360HV oil pump or do you think the OEM pump will suffice now? Thanks again.

[@advorsky1]

Another amazing video thanks for all you teach us!

[@vegasheat71]

My truck ( A 2001 F150 XLT 5.4 w/ 260,000 + miles) just started this ticking, So from your advice I should just take this as an opportunity to change the cams, rockers, and lifters? Should I also change out timing chain, tensioners etc? Water pump? The engine still runs strong. So your word will determine which way I go with this. Thanks to you, and your detailed videos I've been able to keep my truck running like the beast it was made to be.

[@MiKe-fg1el]

Thank you for posting all the great info on this and other videos related.

[@poppacapinya]

my dad is getting an 08 from my friend who got it for free .it of course needs exhaust manifold studs, plugs and a fuel pump control module. so when im in there i figured id check the cam followers . it has 170 k on the clock and its in michigan all though the body and frame look pretty good i figure id make it safe and reliable for my dad. as always great video cant wait for a bullet proof video.

[@markk3652]

Do a thorough frame inspection on it. My 06 rotted from the inside out. It was too late to save it by the time it was noticed.

[@poppacapinya]

@@markk3652 the frame is surprisingly in great shape its still mostly black still i went around and tapped it with a hammer seems pretty solid still

[@edwardmyers1746]

Man them new cams, & kibbles/bits look good!

[@RSH592]

Great Video!!! Not sure if I would trailer an 05 from Cali but good job!!

[@JerryDGossel]

Thanks I have a Major Noise 4.6 2004 Expidtion It lost oil PSI , so with 220000 miles. I better find a core and do a complete rebuild! Flat rate is 11 Hours to do the OIL pump! and Now I see I better do the Cams! Have a Great 2022!!!!

[@db88616]

Brian, thank you for the quality instructional videos. I own a 2005 F350 4X4 with the V10 3V 161,000 miles. Is this something I should be replacing on this V10? Everything seems to run good on it. No noticeable noise, I only put 4-5,000 miles a year on it, mostly towing. I change the oil once a year with Mobil 1 full synthetic. Thanks for any recommendations.

[@bob14219]

Another engine that FORD should be proud of - thank goodness that you have the talents of a bomb disposal unit technician to work on them......what a pain in the butt !

[@nickhoffman5524]

Love your vids most thorough out there

[@Maverickf22flyer]

Hope they'll get back to the classical cam to tappet design with no rollers and improve that if possible, because yes, the roller doesn't have enough or good lubrication on it's small bearing which starts to wear out first and from there the domino comes into play. Great video man!

[@davevincent5024]

Sad that there are no competent shops between Yorkville Illinois and the West coast? Good for you but it doesn't say much for the rest of the automotive repair industry, good job, keep up the great work

[@ts302]

Thank you Brian. To clarify, the roller followers fail and not some other issue that causes them to fail. Thank you, Tony 2010 4.6L 3V.

[@isaiaszepeda42]

Great video. I have a 95mustang that you have to crank a few times before it starts any feedback or any videos you may have on this

[@HazardWolfCorp]

Think imma save up and send my truck to you when its time for a timing job xD absolute perfection.

[@jerryrounds8586]

Excellent video as always.

[@jesussavesletyourgooddeeds3623]

Thanks for all the videos sir the lord answered my family this year with a 2010 expedition,waited for a year always give the lord a year as the parable says about the fig tree but anyway I’ve used two of your vids to fix something on it .

[@wilamun]

Good video ... I bought my '09 with 158,000 kMs. I have done the front end a couple of times, but never the phasers or roller followers. I just had them done this summer, at 596,000 kMs. While it has always sounded noisy since I bought it, I cannot believe the difference in how quiet it is now. In checking all of the old followers, there were only a couple that felt like they might be a little looser than the rest but not to the point they felt rough, even once the oil was washed out of the needle bearings. And once I cleaned a phaser out and re-assembled it, without the spring, it no longer would slide back and forth. I strictly use Castrol full synthetic oil, 5-30 for the past 80,000 kMs or so. I do have a HV Mellings pump. Personally, I think that this is a great engine, and with the service it has given me, how could I ask for more? I am surprised that there is not really much performance work done with it, but hey, we have all of the coyotes I guess !!!

[@ethandupit73]

Hey which roller followers did you use? The ones linked in the video? Theyre $18 a piece and ik there are ones on rock auto for 4 or 5 bucks

[@wilamun]

@@ethandupit73 Ford ... only ... I stick to Ford parts since finding cheaper parts simply do not last. Perhaps they are cheaper, perhaps they are the same but downtime sucks. I ran my originals for a long time with lots of idle time so I just chose to go original. Besides the newer ones are upgraded.

[@ethandupit73]

@@wilamun thank you so much. And just to clarify the newer Ford ones have the smaller hole to hold pressure better right?

[@wilamun]

@@ethandupit73 Yes, they do. One thing I really like is how quiet my engine is runs now ...

[@allnoyz7895]

Smart customer goes to a smart mechanic. Nice!

[@gorybonghit3211]

youre an insnely good mechanic, brian. what are your thoughts on the ford performance hot rod cams for these motors? theyre developed by the same engineers who created the 5.4 3v, id love to hear your thoughts

[@artstoker226]

Great and helpful videos, thanks

[@mattharrell3706]

Awesome video! Love the channel!!

[@wallacejeffery5786]

Outstanding explanation

[@1911smokinggun]

I'm going to be making an appointment soon... from Detroit

[@reneb91964]

Hey there, appreciate your expertize and videos. Did a timing set replacementat 135k miles, rolloer followers were not replaced, 15k later it started ticking. Took out the cam saw metal shavings, the CAM needs to be replaced, but do heads need replacement too? Looks like some scoring on the towers where they hold /meet the camshaft in place.

[@basimfara]

Best as always, keep up fellow.👍😘

[@canadianmarauder1923]

Man I see all these problems with the 5.4 3v but nothing has happened to my 08 yet. You are about the only person who fixes these engines. Everyone else changes whole engine it seems.

[@PsalmFourteenOne]

The engines aren't all bad. The weak point is the top end and not every one fails. They are a pretty damn good engine when they can go 200k+ miles and then throw on a new timing set and followers then go another couple hundred before the bottom wears out.

[@mph5896]

They are fairly easy to work on. The part I absolutely hate are exhaust manifolds.

[@PsalmFourteenOne]

@@mph5896 I turbo charged a 4.6 2V Mustang and I had to unbolt the motor mounts and lift the engine one side at a time to even get to those bolts!

[@scottb3637]

@@PsalmFourteenOne got to watch the connecting rods when you start boosting them. I don't know what year they started using powered metal con rods , I know that the 04 - 08 models are weak there.

[@PsalmFourteenOne]

@@scottb3637 I'm not sure how much is different from the early 4.6 2V engines to the later 5.4 3V, but those sure as heck take abuse! I had a bit of detonation with nmy 4.6 Mustang GT as I tried to tune mine and it never broke a piston or rod. Whew! LOL. After I ran it turbocharged a while I returned it to stock and my daughter drove it until she was able to afford another car. It still ran when she sold it.

[@cma8165]

Looking forward to your "Bullet Proof" video which I hope you'll be putting out soon! IDK if I should spend some $$$ on my '05 F150 with the 3 valve 5.4L or just opt instead for a brand new truck! Either way, it's gonna take a lot of $$$...

[@rodneybrand8521]

That's a costly mistake..you are the professor on ford engines..thank you for sharing..Cheers 🍻🍻🇺🇸🇺🇸🇺🇸

[@TwentytenS4B8]

I'm not so sure it was a mistake. The first shop skimped on changing the followers and probably charged the customer for them. I've been the victim of this before. Also, there was no marks on the phaser and timing chain where they would have timed it up. To me, that is worrisome that it wasn't timed right on top of it.

[@hyper-1]

Thank you, very well done and explained. New sub.