Ford Quick Tips: #4 Ford Capless Fuel Filler Maintenance

[@SpideysNo1Fan]

Even now this is relevant! I have a 2014 Mustang and I appreciate this more than you know!! You saved me so much money!

[@xxheadxxz]

Same here but for a 2016 f150 😂 just bought it was freaking out like wtf then I realized the gas cap doesn't seal 😂

[@victormendez3860]

About to try this on my 2012. Hope it helps

[@jamescor1491]

So my 2013 F-150 with 24000 miles started throwing check fuel filler door warning so I was blessed to locate your video and I did exactly what you recommended. It cleared the warning and engine light. Thank you so much for your expertise. God’s blessings on your life. Now I can inspect my truck. You are the MAN.🙏😊

[@grantdubridge7995]

He is the master of knowledge on the Ford vehicles. You better watch all his truck videos to know ahead of time what will happen to your truck.

[@robgoald]

Dude! Thank you!!! 2015 Ford Explorer Sport. Got the "Check Fuel Fill Inlet" message after a fill up. I thought either my locking cap or that hinged door was bad. I removed the cap and used a pen to make sure the little door was working. After 2 days of driving (getting the "check inlet" message at every start-up) it finally threw a P0456 CEL. I found your video and did exactly what you said, then cleared the code. Hasn't come back in 2 fill-ups.

[@noelelnolo9642]

Thank u for the explanation behind the video and specifically telling us that Ford recommends doing this maintenance periodically. Now I have to do it on my daughter’s Buick Enclave.

[@jiggidyjam]

Thanks a lot Brian. I have a 2014 f150 5.0 with a p0451 and I preformed this exactly and reset the code and it’s been several hrs without the check engine light coming back on. I was very close to going to the stealership to get a 121.00 evap pressure sensor. Thx again

[@sny1168]

I had this happen on our 2019 Ford Edge SEL with only 10,000 miles on it. Looks like Ford has really improved on this problem.

[@gregblanchard3438]

Thank you VERY much for this info video. Have a 2010 Fusion SEL 2.5 and the check engine came in the other day. Tried cleaning fuel neck as you suggested. After first trip and restart...light out:) Thanks again

[@sharisethewordchef4396]

Thanks so much for this info. I have a 2014 Edge and the filler cap is still recessed like the Fusion you show, not flush like the newer one. It looks clean and well-sealed at this point. I did notice a diagram inside the door that indicates to wait 5 seconds before pulling nozzle out after fill-up. I've already had the purge valve replaced in the last week and while the check engine light did not come on this time, it didn't want to start after filling today. Been driving it since October so I guess it just took time to show up, but the dealer records did indicate whoever owned it back in July 2014 brought it in for check engine light but they couldn't duplicate it. I'll wait the 5 sec next time and cross my fingers. Best example of "it ain't broke don't fix it." Stupid move Ford.

[@Jayman001]

I did exactly what you said to do except for my 2013 F150 didn't have a capless funnel I picked one up at advance auto for little under 2 bux, sprayed very little WD40 and sure enuf that next day warning message was gone, lol!! I used compressed air from a can. Thank you so much for your help. PLEASE Keep posting videos.

[@bhepp344]

Thank you! Did this on my 2010 f150 solved my problem and was able to pass inspection! Your the man!

[@CallmeDaBreeze1971]

I just picked up a 2009 F-150 with just 70,000 miles. I will be looking after the filler neck, and keeping it clean. I read about the funnel in the owners's manual and checked to make sure it was there. Thanks for this.

[@joeodell8115]

Thanks for the tip my 2012 Ford Escape is haunted by the engine light cause of fuel evap sometimes it goes away but it always comes back ! I will try your fix today . Thank you , Joe

[@davidsherman6416]

2010 Ford Fusion. Works every time. Thanks for the video. I used WD40 cleaned it out. Reset check engine. First time was $450 at garage cause they convinced me to change sensor. Thanks again for your video.

[@GREATTECH1]

Thanks!!!

[@davidgoossen113]

Thanks. Have 2009 FORD Escape and P0457 on the code reader and smelling gasoline inside the cabin while driving. Will try this first before going to shop. A lot of good information

[@LumiereRAN]

It works on my Ford Fiesta 2013 SE. I did it outside walmart to give it a try And it works! I didnt use that tube thing i just cleaned around it. It cost me less than $20. Thank you so much! God bless man!

[@YamashiKanzaki]

Thanks for putting this up. My 2015 Mustang was throwing constantly throwing codes. I tested if it was the cap by slapping a piece of duct tape on it. No more codes so far... After a few days to really give it a chance to throw a code, I'll try this. Much appreciated!

[@patrogers8912]

doing this tomorrow for my 11 ford edge, keeping it simple and hoping this works; ordered the evap purge valve too hoping this helps, everything ford this is the channel for weird stuff like this. thank you

[@melissae419]

Same issue with the newer capless design. I have a 2013 Edge and it's been giving us some issues for some time now. The check engine light has been coming on with the fuel code and noticed that engine starts odd just after fueling. We will use this method to remove debris and plan to invest in a locking cap. Sadly this probably won't be recalled because it is not technically a "safety" issue.

[@MrFastFox666]

"Easy Fuel" like if removing a cap was such a big hassle lol. I prefer the good old cap.

[@DirtyAfrica]

Mad you dont have

[@calvinwilson2456]

Cap is really no hassle! More check engine lights involving gas refueling than ever.

[@kgardner004]

Super stupid idea from Ford they created work for themselves no wonder their stock is less than 3 bucks

[@judybigbooty108]

@@kgardner004 Ford stocks are actually $12.30 not $3

[@kgardner004]

@@judybigbooty108 oh maybe they're trying to make a comeback

[@HHH-ye1ro]

Thank you so much for posting this. I followed it to the tee, and it worked. I just came back from a 300 mile trip, and no code returned. 👍👍

[@ericbart6574]

RE: 2010 Ford Escape. Full disclosure: My first impression of inserting the Fuel Fill Funnel multiple times seemed lame. I followed the instructions as demonstrated in your video yesterday. Today both the Fuel Inlet warning and Engine Check Light are off. THANK YOU VERY MUCH.

[@FordTechMakuloco]

+Eric Bart Not lame these are real instructions from Ford and it works!

[@ericbart6574]

Yes, I agree. I was wrong in thinking it was lame. I quickly changed my mind because it did work. Again, Thank You for sharing these instructions.

[@BossSpringsteen69]

You mean the fuel inlet and check lights got off. Ok, bad joke but, i am waiting for the day i might have to do this procedure because i have a 2014 Fusion. The first thing i thought of when i saw the capless fuel filler is dirt in the fuel tank and the little door sticking open.

[@Powerpickle68]

I will do this because I just got the very same code but first the dash display showed "check fuel fill inlet" a few days prior. Then the check engine light came on for a few days,went off and now back on. Thanks for the video!

[@tgferg67]

Another genius idea by Ford - I have wasted more time troubleshooting and fixing versus having a conventional gas cap.

[@chrisloffredo7418]

I followed your directions and used an Actron OBD diagnostic tool to reset the EVAP codes I just went to emissions and passed thanks for the online help really appreciated.

[@FordTechMakuloco]

+Chris Loffredo Awesome!

[@spruitt626]

Hello FordTechMakuloco. Thanks for the tip. I have a 2010 Taurus SEL and my check engine light was on. It was giving me the 'small evap leak' code P0442. I follow your instructions and it worked...lol. It's been a few days now and my light has not come back on. Thanks for the tip.

[@deathDPpuppet]

I have a 2013 mustang V6 I got this issue with the check engine light. The scanner was showing EVAP leak I kept on clearing the code then then recently the on-board computer showed to check fule cap. I guess this is the cause of it as I live in qatar and it's quite dusty over her and there is now self service filling. Thanks for the video 👏🏻

[@Darwinpasta]

Wow, there's a solution in search of a problem! Thanks for showing how to make the bugger work again.

[@grantmcdonald1109]

I live up in Canada where there is a lot of dust,mud and snow in the winter so I bought a locking cap from my ford dealer that covers that filler entrance on my 2010 f150. It work very well.

[@sanequadallas9936]

So you bought a locking cap in don’t have any problem because I was thinking about buying one. Is it easy to take off

[@garrykoalman3684]

I will admit that the capless filler neck is a great feature for putting more money into the pockets stealerships.

[@juanguerrero9128]

I agree. I have a 2010 f150 the the spring broke from the gas door and its about $500 to get a new one.

[@gerryrig5012]

Ford Should Have A Option For A Gas Cap For Capless Filler...

[@florret2003]

@@gerryrig5012 I have a Ford locking cap available from them on my Flex. Keeps out dust and dirt and anyone looking to create mischief.

[@jdigitalseven7]

Its to prevent your hands from smelling like gasoline

[@Mac_Mixxed]

Dude my 2009 ford explorer gas cap spring broke and it now pops out the wrong direction and i have no idea how to fix it

[@Apoplectic2009]

My 09' Lincoln MKS had the check engine light that has to do with this fuel filler neck message appeared on dashboard. Lincoln Dealer tried to rip me off with $500 charge on the replacement of fuel pipe neck part without discussing the cost ahead of time. I told them to put the old part back in and follow the instruction of this video. So far my car has no check engine light appear since 2 weeks after I erased the code. Also, I took it to inspection and it passed without any issue. Again, thanks for this wonderful tip. Any Ford or Lincoln owners should follow this guide before wasting money for dealership service.

[@FordTechMakuloco]

Well that is good then glad it worked!

[@dbeck963]

Thank you it worked on my 2013 mustang. The key was to make sure to spray the WD 40 and work it in with the funnel.

[@alpindrock5597]

Thanks for the tip! 2011 Mercury Mariner. Fixed throwing the dash warning check fuel fill inlet and then check engine light on. Performed cleaning then reset by battery disconnect/reconnect.

[@tj3688]

I have a 2012 Ford Fusion. This worked! The check engine light went off. Thanks so much! This saved a ton of money if i had taken it to a mechanic!

[@samanthawimberly1270]

We brought our Chevy into the dealer and it needed a new fuel pump. Again. Anyway, upon picking it up it was throwing code p0455. Large evap leak. We’ve taken it back to them 7 times now and they all but literally like you said are throwing parts at it and we still have a leak. They say it’s fixed every time. Tomorrow I’m going to autozone and trying this to see if I can fix the problem myself. This area is filthy so they clearly haven’t done it

[@bricks312100]

Seriously, thanks for all the time you spend on your videos.

[@davidklimmek3192]

never any any issues with the capless system on 5 newer Ford/Lincolns myself & family bought since '12. Love the system ..no gas mess!

[@biker932012]

Whats so messy about removing and tightening a gas cap? Been doing it for the last 6 years ive been driving, haven't spilled gas on the truck yet...then again I wait till the gas stops flowing before I pull out the nozzle.

[@stevansweeney]

Thank you for the video. If you don't have the emergency funnel, 1/2 inch plastic flexible electrical conduit works well too.

[@toadmarz]

My 2011 Lincoln MKX coded P0456 (very small EVAP Leak) I followed your advice for cleaning no cap gas filler and cleared code. It has not returned. Thank you , this could have cost me alot to chase down at a repair shop.

[@marvincrompton]

Thanks for the tip. Had this problem on my 2010 fusion and had to take it to the dealer. The work order indicated that they had to clean debris from the cap less filler neck to resolve the issue. Thankfully it was covered under warranty.

[@FordTechMakuloco]

Now you know how to do it yourself for when you are out of warranty.

[@opaulofranco]

Nice one!!! Thank you for that!!! I have a Ford Fusion 2012 SE. There's some smell into the cabin specially when I have half a tank or more, and it makes me seriously sick. I took for a full check, and they said "nothing wrong". Any shot?

[@gabriellelowe7422]

Thank you so much for your expertise on helping me fix my own problem without taking me Ford Expiditiion ( 2013) to the shop. This fuel valve sensor has been giving me troubles since I bought it....then they said to never overfill it with gas. So I unplugged the battery like you said in a previous KZbin ...still came on...now I know I will go buy some air- pray and clean out the the surrounding area and put in some fuel cleaner. Please let me know if there is anything else you can suggest.. Much love and grattitude for your help! Stay blessed always 🙏💞

[@jermaineyoung7256]

Changed my 2013 Fusion SE catalytic converter in March and then this started happening. Cleared it following your instructions, minus the compressed air, and it just came back on. Will try golpe said instructions to the T and clear the codes and see what happens

[@smpitmanVT]

Thank you! Saved me 4 hours round trip to the deraler and probably $250 in unnecessary repair.

[@bperkoski]

Thanks for this! I have a 2011 Mecury Milan. I started getting the check fuel fill inlet months ago. Then about a month ago the check engine light. Knew the 2 were related. But didn't know what to do. Used your tip on Saturday morning. Check engine light is now off & my avg. mpg is back to normal. Thanks!!!

[@ekojar3047]

My coworker just got stuck at a gas station because of the " Easy Fuel" the pump nozzle was just a little bit too small to catch the releases on both sides. this is on a brand new ford fiesta! call me old fashion but I'll stick with the ancient twist cap. Nice video by the way. thanks!

[@alexhulinsky7954]

"nozzle was just a little bit too small to catch the releases" what releases are you talking about?

[@budlogan9720]

I love the capless filler. As with any new innovation Ford will get it figured out. Mine is a 2012 and the problem just started. Im happy if that is all it is.

[@guycripplecock7804]

That is why the funnel under the seat

[@bipaholic]

Thanks for the video, I just got the check fuel fill inlet warning on my dash on my 2010 f 150. I’ll give this a try

[@RighttothePointDIY]

Great video! My daughter just bought a 2012 Ford Focus and the first day she filled up the tank she got a code. The dealer is 99% sure this is it. I'll clean it out, clear the code and see what happens. Thanks again for the great video!

[@Gman12959]

Yeah I get power assist failure too from time to time, think it’s a cpu or wiring problem. But I’ll look into getting that filler neck and new door spring

[@suemartin1319]

My 2010 Ford Escape started showing Check Fuel Inlet then quickly changed to check engine light it was due for Inspection and Emission took it in to my garage who I love they cleaned it all out it passed Inspection and Emissions then 1 week later CHECK ENGINE LIGHT again so I started doing a little research and found out that this has been an ongoing problem with many many Ford owners. I found this video on You Tube which seems to be a simple solution Im going to try it then get a gas cap to keep it sealed. I will post again to let you know if it worked.

[@heathern10]

Sue Martin I just had the exact same thing happen to me today. My check fuel inlet came on, followed by the check engine light on. How have things turned out since getting a gas cap?

[@chrisea]

Sue Martin I think you forgot

[@WolfgangReil]

Had the error come up yesterday for the first time 135k on the odo. Suspected something stuck the flap open just enough after refueling for a road trip. Got the fuel filler tube out and did the 30x insertions (more or less) and the indication didn't come back. Now, after having checked out this video, I can clean it up without taking it in to the dealer.

[@lifuranph.d.9440]

I had this issue on my 3.7L, 2017 T-250 at 702 miles...702. Thanks. PS My T-250, 3.2L Never had any issues with the filler cap. Diesel fuel is a good lube and Cleaner.

[@DinaMali]

Wow we have been having so much trouble with that dumb light and were about to spend money to get it smoke tested and some other stuff. Thanks to my husband who found this video well we will see how well it works. Thanks God Bless you!

[@FordTechMakuloco]

Dina Mali It's either this or the canister purge valve yes very simple and most of the time smoke test wont show, I don't even do them anymore.

[@DJDannyUhOh]

I had same problem with my 2010 Escape, turns out there is a rubber o-ring around the inside the metal flap/gate part inside that started breaking down. Was hell to get in there and replace it.

[@canyon12alex]

What if no CEL problem but having major issues with fueling. Most nozzles only allows 2-3 seconds of flow no matter angle of nozzle to port, pressure, limiting handle to attempt slower flow, pulling back the shroud. Only cheaper tiered stations work. Perplexed. 2020 Fusion Hybrid SE 5k miles. I would highly value your opinion. Dealership always wants to go down vapor lock trail.

[@nosefirst]

Thanks for this quick video! It never occurred to me that there might be seals on this "feature" that could have a problem. I will take a look at my 2014 Focus when I get it back from the service department sometime next week.

[@johnmasters6257]

Been chasing a P0456 for two months. replaced purge valve, did this procedure, now finally replacing filler neck...fingers crossed.

[@luktish]

John Masters how hard was it to change filler neck?

[@johnnyrizzo8057]

Good tip, never thought about debris falling into the tank.

[@MrJustus152]

I have a 2020 Escape with less than 11,000 miles. My check engine lite came on for that exact problem. Thing is it's clean around the filler.

[@EricFortuneJr.]

They sell aftermarket locks that can be placed over the capless system, I used to sell them for about $8-$10 mostly for people who are concerned about vandalism but they’ll definitely keep dirt and road grime out.

[@emperordonaldtrump1st614]

Sir what's the website or where do they sell them i hate this new capless bullshot

[@EricFortuneJr.]

Clutch3Pointer I used to work at O’Reilly Auto, I sold one to a lady who purchased a Ford Focus with “capless”. She thought her cap was missing. After I explained to her that it was a capless system she said she still wasn’t comfortable with it being open so I sold her a lock specifically designed for her model. They don’t twist on, you just stick it on and there’s a little tab that will hold on there. It comes with two keys so you can lock it if you want to. Most auto parts retailers should carry them but I sold one from O’Reilly..

[@EricFortuneJr.]

Clutch3Pointer Have them look it up for your car's make and model.. Could save a service trip to the dealership.

[@rossocampo4131]

We had 2009 ford escape with p0422 code. We replaced the purge valve, masking taped the fuel capless, bought fuel cap with key still the engine light is lit. We tried to wiggle the end of the rubber hose attached to the fuel tank & tighten the o ring clamp it works. The small leak comming from the hook of the o ring clamp inserted in the rubber hose. You can add 1 o ring clamp side by side to prevent leaking again.

[@rossocampo4131]

Sorry it is p0442.

[@McBosshog85]

Super common problem with the 12th gen F150 as well.

[@billgurd4177]

Thanks for the video. I have a 2012 SEL and my engine light came on and I knew what it was right away from watching this video before I bought the car.

[@xantia2007]

Takes the expression "Splash and dash" to a whole new level. I just got 2019 Ford Tourneo and it has one of these filler systems. What makes me laugh is the lack of security as the flap is not lockable.

[@joeodell8115]

Stant makes a locking insert for that filler system I have one on my Escape .

[@mexjoker8027]

My 2013 5.0 mustang has this problem too, I'm going to try this out and see if it helps. P0455 code evap leak

[@89G]

I'd just like to add that I dealt with this issue several times on my 2011 Escape. I was curious if putting an aftermarket locking gas cap would at least make it less frequent. About 18 months ago I purchased one, and I have not had another check engine light since.

[@mizzjonezz]

Can you share a link to the one you purchased? I need one for the same issue

[@89G]

@@mizzjonezz unfortunately, KZbin disabled link sharing in the comments. I can give you the part number though. It is a Stant 10524, and I got it on Amazon.

[@GREATTECH1]

Thanks so much. Will try to get as much info as possible.

[@almetcalfe159]

I had gasoline odours on my 2011 Explorer and using this video solved my problem. Thank you

[@Dreccomel193]

Thank you for taking the time to make this video. I have a follow up questions, I saw your video in regards to a P0456. As indicated in that video, I tested and replace the piece. I also followed the directions indicated here. I just found out that there's a locking cap (Part # 31859) and would like to know if it will help with any future issues or would it make it worse.

[@LaughOutLouie88]

That’s what I will be testing out soon will keep you posted. I have the same code popping out for the second time now since buying my Ford Flex about 3 weeks ago. I did this and pumped gas and it cleared up the check engine light immediately after filling up but the light came back on yesterday.

[@johnsmith-dm2tq]

Ford escape question? I have a standard 2.5 and need a new motor. Is a 2.5 from a hybrid a good donor? Different motor mounts? Thanks to anyone who knows this as used hybrida are a dime a dozen around here

[@johnsmith-dm2tq]

Lol, way to go Ford. You solved a problem no one had. I have this on my escape and just want a cap

[@dirkmcghee1604]

I appreciate your intro music not being annoying KZbin bs trancy nonsense!

[@bgh70]

Thanks for posting this. I'm having this same problem with my 2011 Fusion. I'll give this a try and see how it works.

[@lopesanderson19]

bgh70 did it solve your problem?

[@kingshaun2x]

Did it work ?

[@gabrielescobar4996]

Did it work when you cleaned your tank

[@Jamesfusion-xb5xt]

I tried this and it worked for a while then code came back. I found that taking fuel hose at each fill up and and doing what yu did with funnel has kept code off for the past 6 months now. Before I did that the code would come on for small evaporative leak. My two cents maybe this will help someone else too

[@riphaven]

For a hundred plus years the filler cap work, but wait...ford has an idea. Why you ask? Because some ford engineer fresh out of school wanted to have a hand in the design and this was his contribution.

[@biker932012]

seems to be the truth anymore...smh

[@petehorrorwood]

Hey man any chance issues with this cap free system would throw a p0442 On a mustang? I have the same system on a 17 mustang gt

[@josephdelk708]

Fortunately, I haven't had this problem. Thanks again for showing this. This is why I'm glad I found your channel and subscribed. I'll make this part of my maintenance routine. Joe D.

[@FordTechMakuloco]

Sounds good to me, just getting the information out there.

[@PRO356-Custom]

My 2010 F150 is having this problem, there is no rubber gasket seal on the door itself. I tried the method to clean the inner flap numerous times but it is not sealing enough to make the error message go away. Is there anything else to try before replacing the filler neck? Or is there an aftermarket product that I could use?

[@Sheeeeeeeeeeeeiiitt]

Marc, any luck?

[@raggidyman2949]

so you blow it, stick it in 30 times, blow it, lube it and stick in again?

[@juanguerrero9128]

Yeah cause u really don't want the vehicle on top of u doing all the work. 😅😂

[@thegoodlifegrind5065]

Right! Lol

[@howardkerr8174]

When you put it like that, it sounds like a busy saturday night at a brothel.

[@BadRonald1]

Yes this is called Ford Foreplay

[@pugsandcoffeeplease]

@@BadRonald1 Fordplay.

[@zzzubmno2755]

i have a 2011 lincoln mkx with that type of fuel cap. when i first saw it, i thought, cool, as time went on, i was like, hmmmm, that thing doesnt seem like it will seal forever and will cost me fortune to fix. going to follow your tips, clean it right out regularly and hope my pos doesnt fook up.

[@Sjhssucks]

Do you have a video on replacing a cap less filler neck on a 2010 explorer or like wise vehicle? +FordTechMakuloco

[@michaelschwarz9114]

I have a 2014 Mustang GT with capless fuel filler and have been getting the code. It was mentioned during the video that Ford fixed the issue in 2013 and newer models. I have tried this method once or twice but not exactly like this video describes. Should I try this method after clearing the code or might I have a larger issue?

[@tobystanski6468]

the emission,evap,check engine symbol came up 2015 ford and i sprayed wd40 on fuel flapper like in video, it went off. thx

[@jperezl1581]

Hi i own a 2010 Ford Escape. The silver or metal flap valve that covers the hole that gets pushed in when inserting the gas nozzle looks like its pushed back and gets stuck when pushed back. When i pull it forward with a wire, it gets stuck halfways. Preventing me from fueling up. When i try fueling up, fuel leaks from the bottom of the truck. Could the flap valve be broken or need to push to push it forward to line up evenly?

[@robertphillips9833]

Dont fix it if it is not broken. Aka the gas cap does its job perfectly.

[@mexjoker8027]

Robert Phillips until you need to go get emission test

[@BossSpringsteen69]

I had a gas cap sealing issue that was solved by buying a new gas cap. Easy peazy. I'm just waiting for my Fusion to have an issue.

[@717dash_cam]

@@BossSpringsteen69 Do yourself a favor and buy the locking cap for the ez-fill fuel system off amazon. I did that after having an issue on my 09, should help keep crap out of the filler neck.

[@Michele0403]

And, after getting 1/2 tank of gas stolen, I went and bought a locking gas cap for my 2017 Ford Explorer XLT.... Michele0403 3 years ago The car comes with a special funnel, in case you have to fill with a gas can. If the bad guys have that funnel, then they could get the gas out too. I filled up the tank the night before FULL. The next day, I get ready to take my road trip, and the tank is half empty. Also, every time I get gas, I reset the "trip", so it's at zero, so if anyone drove the car, it would have a reading, other than zero. How would YOU explain the missing half tank of gas? Nobody else has access to my keys.

[@rmsh24ify]

Thx for uploading this video 👍👍 I have a Ford Fusion 2012 and it's getting on my last never with this check light...I took it to the dealer and they used the computer to turn it off and now it's bk on again!! Am trading it in for a Honda Pilot I can't take the stress

[@MrKING-gn5ku]

+rmsh24ify Check for trouble code p0457 or p0455 it is probably the vapor canister solenoid part #911-222. A local dealer in my area gave me the part number and told me how to put it in myself. The part in 2012 was about $60.00 I saved $200+ on labor. it took me about 30 minutes to put it in would have been less than 10 minutes, but I dropped one of the screws in my engine. If it is the SE V6 the part is on the top of the engine to the left of the battery. This worked for me I hope it works for you,

[@Ultrajamz]

They sell a cap you can always put on there if it wont be fixed. To people who say capless sucks, I've owned cars where the cap system itself wont seal right, and you need to get another one. So really theirs no winning.

[@FordTechMakuloco]

Yes I link to the dust cap in the video description.

[@juanguerrero9128]

How much is a cap compare to fixing the capless system and u will understand the difference.

[@picklerix6162]

I paid $7 for a new gas cap. That's a win for me.

[@hypopastel22]

capless sucks I'm getting evap codes, first small leak now showing large leak on my 2009 mercury Mariner thanks for your videos I'm going to check the purge valve then clean out the fuel intake I hope it works.

[@ruizhernandeztrustfi]

Why ford keeps overcomplicating things? It's amazing how many different parts are needed (in a complete new and faulty system) just to get rid of a $15.00 gas cap. It's stupid.

[@fiddys3v3n]

Don’t blame Ford for this ridiculous idea. Ford didn’t introduce cap-less filler tubes for its customers’ convenience. It is our over-reaching governments who regulated them into being. Fuel in a vehicle’s tank and fuel lines will evaporate over time, releasing gas vapors to the atmosphere. Vapors also escape when you re-fuel your tank, as well (we’ve all smelled that, it’s the reason we don’t strike a match within 25’!). So the geniuses at the EPA and other tree-huggers lobbied big government to act. They did so by regulating that those emissions be reduced or eliminated. That is why evaporative emission control (EVAP) systems are now common in all new vehicles. Big Brother decided this is what’s best for you, not Ford.

[@greetswithfire1868]

@@fiddys3v3n These capless fuel filler systems are not mandated by the government or they all would have them. There are many newer vehicles that have gas caps.

[@marvincrompton]

Is it possible to test the cap for a leak simply by spraying WD-40 on top of the cap less filler and observing whether the fluid seeps through or remains submerged on top? Do you think that is somewhat of a valid test?

[@dm7097]

Omg, I just bought a '10 f-150, I saw that funnel sitting under the back seat and was wondering what it was for! S.m.h

[@mrburger5932]

same here

[@garymcnay8529]

I have a 2012 Fusion with this exact problem....will try and let you know if it helps.

[@lahrgsp]

Do you have a video on how to replace this?

[@ibrahimalfaiyez3404]

THANK YOU SO MUCH! Yoy saved me a lot of money!! I have Ford fusion 2014 SE 2.5 with P260F code( engine light and other un related lights shows up on my dashboard). I did it and the code is gone and I passed the smog test! New CA law from July 1,2019, if any code related to fuel evaporation will FAIL the smog test! Make sure to scan your car before to take it to smog test!

[@treydaypnw]

Great vids man. I just can't help but to think that the Cap less fuel filler is a Bad design.

[@donaldbrown1300]

I have a 2019 Mustang GT and I noticed it is always damp with fuel around the capless filler. I assume this is due to venting? No codes at this time. Is this normal?

[@jimreyes9576]

I did it at a gas station with the fuel gun. People look at me like if I was crazy or a pervert.😠

[@fatimariv47]

lmao same

[@PhilDrew1]

It may have been the moaning. :)

[@BossSpringsteen69]

Yeah, i saw you at the Shell station.

[@baluxyanahiam3630]

🤣😂 Same here and it didn't work

[@JayVeMontgomery]

🤣

[@jefflarner]

I have a 2014 Ford Fusion with the po456 code. I noticed the inner flapper valve on the EZ fill can be opened with my finger. Isn't that supposed to lock to avoid tampering? If so, mine does not..

[@eddiecruz2613]

Try to do it when gas level is low just in case of contamination

[@VexingCode]

Have a 2012 Mustang and had to do this. Ford dropped the ball on the Ez fill design, but thank you for this video! The engine light scared the crap out of me haha

[@klong1972]

I hate the capless setup.

[@ivanibarra9552]

klong1972. You can buy a cap with key lock

[@renesereid6799]

klong1972

[@IWeasel]

I love it had it on my 11,12,14 never ever had any issues

[@tedcarl5382]

Ivan Ibarra doesn’t have a seal so it doesn’t solve the problem.

[@armstrong4196]

Buy a fuel plug lock in Amazon. They are about $25 or so.

[@peterbellisario6904]

my guess as to the reason for these gas caps is to not release gasoline vapors into the air. When a regular cap is opened, and you look at it from the side, you can see the vapors escaping. It is easier seen on slightly older cars without the little flapper valve. I remember back in the 70's, a large contributor to smog were these escaped gasses. On the engines in the sixties, there was the oil tube that stuck up from the engine that was covered by a push on cap. In the 70's PCV systems were developed to reduce the escaping vapors that were in the crankcase. btw - screw caps do go bad as well. They need to be replaced at around $10-15 each. With the new design, you get to do some in & out for free!!