I Installed R600a Inverter Compressor In OLD Refrigerator!!

[@somaday2595]

Very clear annunciation, no distracting background music - this helped along with your clear step by step replacement process.

[@-na-nomad6247]

I'm impressed you survived.

[@jameswatters9592]

Its AI

[@Vinline1995]

I fixed the fan motor in my aunt's fridge today. Now youtube recommended me this video, my job looks like kid's job now after seeing what you did😂

[@forevertechenglish]

😂😂

[@The100volvo]

Satisfação por ter instalado um compressor fabricado no Brasil

[@DIYHelper]

Use a pressure regulator for the N2. In Romania these are delivered with 200 Bars. I would really not feed the circuit with this pressure. Regulating pressure by tapping on the valve is just insane. You are only regulating the flow, if the system is not open you can build up that pressure in the circuit....

[@владимирглущенко-л6м]

in 1993 I was 30 and I changed the motor-compressor to r-12 in 45 minutes ... and my knees did not hurt)))

[@PiotrK2022]

Cool, noone cares...

[@kirkstaggs9773]

I'm old myself I get what you're saying. However now my knees always hurt.

[@владимирглущенко-л6м]

@@kirkstaggs9773 ok-ok

[@PiotrK2022]

@@kirkstaggs9773 Still, noone cares... Keep that for yourself.

[@kirkstaggs9773]

@@PiotrK2022 who hurt you? Did your dad leave for milk and cigarettes and never came back? Or does your mom complain about her knees after a hard night's work.

[@Romadedoniamace]

You have acetylene,pressure washer,vacuum pump!,don't have nitrogen regulator?😂😅

[@matt-g-2501]

Absolute illegal in Europe, to release coolant gas into atmosphere. The fine is up to 55000 $

[@soorajsoorajs3385]

Really ? What about methan CO2 ?

[@skydeclair]

It's illegal to small in Europe isn't it,

[@Denis7947.]

Yieks

[@janh7515]

A tie chladničky čo vozite kade tade po Afrike a oni ich tam likviduju len tak to si im bol povedť tiež aby ho nevypušťali do ovzdušia ty mudrc ??? prihriaty ?

[@nicholasfink6170]

You got any religious codes to site.

[@MichaelBeeny]

I'm amazed it's cost effective to replace the compressor and re gas with hours of labour on a very old freezer. I note the old gas was let into the atmosphere. That's not allowed in many countries.

[@forevertechenglish]

Yes Inverter compressors work on variable frequency drive, which makes them to adjust the speed of the compressor using control boards. Also they can be smartly Used with thermistors to control the refrigerator temperature, Well I checked one of your video too. You are doing good work to. Appreciate your work too.

[@liquidsoftpc]

in their country it is much cheaper to repair the unit rather than buying a new one.

[@forevertechenglish]

Yes it do is..

[@johgude5045]

what he does is illegal everywhere on this planet. He MUST not release the R134 to the atmosphere

[@lazzynur]

@johgude5045 you can give him recycling machine, he can't afford it

[@smvwees]

Last week my fridge totally gave up. I figured it would be the relais and compressor like in your vid. But since i didn't have all the equipment and knowledge you have, i figured to buy another fridge and let them take away the old one. In contrast to the fridge in your video, mine was pristine from the inside, no filth or stains or anything. I actually hope they refurbish my old one at the depot, since there is already enough waste. Also i am glad there still exist simple fridges that don't have bluetooth or other of those electronics inside. (Unfort. not with washing machines. I can't find a single washing machine anymore with a mechanical clockwork cylinder inside. All bleep bleep electronics now). Keep up the good job!

[@joeds3775]

You can rip the beep beeps out and replace it with older system, or an Arduino

[@dolorescamacho1241]

Check out Speed Queen washers.

[@wesrurede]

You are a perfect candidate for the carbon felt pad used to protect from welding and I'm sure brazing. You'll still need the regular wet cloth to cool. I was amazed it was able to protect whatever I put under it when Arc Welding.

[@mofbombay6290]

Asbestos always worked great , just not good for Health .

[@jannejohansson3383]

Extremely good video, I have old rounded fridge or cooler, what ever it is and want to use it it, but old compressor is working, but for sure, no forever.

[@tronixfix]

Yesterday i convert R600 fridge/ freezer to R134a. Had to change condenser, compressor and filter drier. Also shortened the capillary tube, now freezer compartment is at -25C and fridge compartment at 4C. Pressures when saturated are 5psi on low side and 120psi on high side.

[@forevertechenglish]

Thanks for the info

[@forevertechenglish]

@@el1Mundo on what basis??

[@kareemhameed4042]

Can you explain why you shortened the capillary?

[@tronixfix]

to reduce restriction, with tube in original length the high side was getting too much and the low side went into vacuum@@kareemhameed4042

[@정민준-z1n]

​@@kareemhameed4042모세관이 길면 필요한 압력보다 높아지기 때문입니다.

[@howardsimpson489]

I had several old fridges that had rusted compressor pipes and all the R12 had gone years ago. The compressors still started and ran okay. I replaced the rusted bits with brazed copper pipe. I the pressurised the system with fuel grade LPG (propane butane mix). I then let all the gas out again and did this several times. As I refilled I watched the compressor current which did not get up to the rated current on the compressor label. Ice started to form on the suction side so I bled gas off until it stopped and then a bit more. After the fridge had come down to temperature, a little ice was forming again so I bled off a bit more. Two of those fridges are still okay ten years later,.No vacuum pump, no gauges, no oil change, no capillary change, no problems, lower power use, shorter running cycle just LPG highlighted on the label. Not illegal to bleed LPG to atmosphere. Most domestic gear chucked out can be home repaired.

[@rearspeaker6364]

problem is, that the fridge maybe become a BBQ one day.........

[@ericoppel5698]

@@rearspeaker6364 That's the same thing car mechanics used to say about converting car air conditioners over. It's just nonsense fear mongering. There is so little gas in it that this will never happen. Remember, you have to have the correct fuel/air misture for combustion. Also propane and butane systems run at a lower pressure, so there is even less chance of a leak than before it was converted.

[@rearspeaker6364]

@@ericoppel5698 I'll have to try it in a car air conditioner, using some propane from a forklift.

[@aleks7064]

we still have compressors from Zil Moscow refrigerators, produced in 1971. I installed it on the freezer and filled it with freon R134a. video can be watched on my channel, there is even with English subtitles.

[@takischaros8469]

Congratulations... regards from Athens Greece...

[@forevertechenglish]

appreciated

[@isettech]

Did you know that venting refrigerant to the atmosphere is a crime? It is required to be recovered per EPA 608.

[@forevertechenglish]

Yes, that's true.

[@HydrarDraconis]

Yes, this is horrible advice and you should not show this in a a video, you inspire others to do the same, amount of environmental damage from venting that refrigerant is more than you'll ever save from installing the inverter compressor. At least rent a recovery unit and recycle the r134A

[@forevertechenglish]

Hope To get one in the future, And yes I would not recommend anyone to vent the refrigerant. As I don't have one. I had to vent to fix the unit.

[@sandipsengupta1832]

It seems to me that there was not much R134a left in the unit, since there was only a very brief hissing noise when the line was cut, so comparable to the 'minimis' release allowed by epa, even if technically illegal.

[@zibbybujno5452]

EPA has no jurisdiction in India, just saying 😂😂😂

[@Homestead_Adjacent]

Checking for excess oil in the evaporator is a very in important step. Good he emphasized that

[@forevertechenglish]

Great point!

[@alexandrumarzenco6998]

Why? Could you explain?

[@Homestead_Adjacent]

@@alexandrumarzenco6998 if a compressor is running while there is a leak, the excess temperature of the compressor can atomize the oil that's supposed to stay in the compressor. This oil freezes in the evaporator causing a blockage

[@waynescammell443]

Nitrogen regulator or you may no longer be with us

[@forevertechenglish]

I use it everytime, but I knew no high pressure was required in this case.

[@a123clim]

😅😅😅😂😂😂😂😂

[@John8910]

Ahahahahahahah. You think safety is on the list for overseas guys. He probably doesn't have one. Things are not easy to get don't forget.

[@TheGamerFiFtIn]

He works like someone who has no fucking idea , saw someone doing it and did it

[@joeds3775]

@@forevertechenglish your confusing of flow and pressure is dangerous.

[@DarkySabertooth]

you vented that stuff to atmosphere?

[@micropower8]

If you are measuring the temperature, then go closer to the object. Many sensors have a 30° opening, this means that the sensor-area is around 30cm if you have a distance of 30cm. The laser there is only good to see were is the center-point of this circle. Some sensors have a focal point of 1:12 (2.5cm point at 30cm distance) or some very good with 1:60. Many people are doing it wrong, because they think that the laser itself is the measurement-device. And the surface what you want to measure should be black. If I measure a aluminium surface of a heat-sink, then I paint the surface black with a permanent marker before the measuring. If the black area is only 1cm in diameter, then I use only a distance of 1cm.

[@forevertechenglish]

Oh that's a new thing, thanks man

[@reddragonflyxx657]

​@@forevertechenglish IR thermometers are pretty neat. The one I have uses 2 or more thermocouples to measure the temperature-one exposed to light from the outside and the other not. The temperature difference indicates how much IR light is hitting the sensor. Lenses focus the light, so there's a focal distance where the measurement area is smallest, and getting closer or farther away makes it bigger (think of a magnifying glass focusing sunlight). The manufacturer generally tells you how large the measurement area is for each device. You're measuring the 4th power mean temperature of the measurement area, so if you measure something half hot and half cold the thermometer will show a reading closer to the hotter temperature. The IR emissivity of many materials is >0.9, but certain metals are a common exception. This pretty much means that those metals with low emissivity emit a small percentage of the IR radiation an ideal black body with emissivity 1 would. Such materials often reflect IR, so you're likely to measure the temperature of the reflection and the IR mirror you think you're measuring.

[@Optimuseq]

Instead of using that type of sensor use thermocouple - simple :)

[@micropower8]

@@Optimuseq - Yes, this would be more easy, you only have to get a contact with the other material.

[@Optimuseq]

@@micropower8 more precise

[@jvc22467]

What about reclaim of the refrigerante first

[@markae0]

If you recover the old R-12 or R-134 refrigerant, could you reuse it again (after filtering)? The old refrigerant is very expensive now?

[@harryade7998]

Hi, just wondering how you used a bldc inverter compressor in place of an ac compressor. Would you please kindly explain how it is done. Thanks very much for your awesome videa.

[@szolizoli8151]

Thank you for the education!

[@OilandGasInformation]

Thanks for sharing your knowledge. Keep it up

[@forevertechenglish]

My pleasure

[@TheLoveworldwide]

thank you for your good explanation

[@forevertechenglish]

Glad it was helpful!

[@XavierBetoN]

This video is more educative than the brain-interface program installers in the Matrix. Thanks dude!

[@ebozofred6032]

This my best work that I learne for three years in school please any looking for a job in this settle..

[@Somanathan-hj7ge]

Sir, you are practical as well as theoretical,,and thinking person, perfect tidy job, perfect job done, awasome job sir,

[@forevertechenglish]

Thanks

[@pauloeduardo9604]

Muito bom esse serviço. Pra fazer a nova carga de R600 poderia ter calculado 40% da quantidade original de R134. Isso é o que usam em média. Abraços do Brazil.

[@forevertechenglish]

Obrigado, meu querido irmão. Agradeço seu comentário do brasil

[@carlosm4806]

Not only the comments but also the compressor is made in Brazil 😂

[@forevertechenglish]

@@carlosm4806 yep that's true

[@franciscoferreira-eh1yu]

​@@carlosm4806honest i think all thos video is made in brazil just with english narration

[@t0nito]

@@franciscoferreira-eh1yu Nope, those plugs aren't used in Brazil, those plugs are used in India and some African countries.

[@mehadisyef356]

❤best video 📹 so far🎉 watching u from Bangladesh 🇧🇩!thanks a lotz! Wat a xcellent video so far!

[@SLDYDirectors]

Can the electricity consumption be reduced when the inverter compressor is installed?

[@forevertechenglish]

Yes inverter compressor consumes less electricity than a normal compressor. The starting torque is also low. And normal compressor when start it consumes 1.3 kw of electricity. And after 10 seconds goes to it normal 310 consumption. The inverter compressor starts from 0 amps to its max watt, Depends on what size is the compressor.

[@1marcelfilms]

why must you cut off the access port why cant it be left in place for future refilling ?

[@NikolayIslentev]

It will eventually leak if left unsealed.

[@stepannovotny4291]

@@NikolayIslentev Well, you can torque a cap (with seal) onto it.

[@JohnSmith-el5mo]

So you just release the gas to the atmosphere. Good to see you care about environment. You deserve a medal.

[@TofuInc]

134a has been used as a propellant in aerosol cans for years up until recently when it was phased out and replace with 152a. You're "canned air" was 134a until 2017.

[@matt697845]

Don't even try to communicate or reason with a climatard, they're brainwashed beyond any hope.

[@forevertechenglish]

I do care about the environment, The problem is that human creates an invention and then blames it himself. So we humans do have this nature. And I venting the refrigerant in the air is a mistake. Let me tell you a fact. In most of the Asian countries I have seen most of the people are unaware of the recovery cylinders, which is very bad. They on daily basis vent the refrigerants in the air. No regulations are made to stop harming the environment. Blondie SL its your opinion you put this channel in a no suggestion list. I will Humbly Respect that. And I in my opinion giving heart to the comments is too respect their opinions.

[@forevertechenglish]

Well you think, I am scaming as it was my choice, Well thats what you think and I can't change it. Well we need to save this planet. And the recovery cylinder costs way too much in my country. That is why we have to make this choice. Otherwise I would have used the recovery cylinder. And yes that is why I made this choice. No offense to you. I respect all what you say. Thanks mate for a nice talk.

[@JohnSmith-el5mo]

@@forevertechenglish Dear friend, I dont think you are a scammer and i believe you are a very smart guy. The whole world is watching your highly skilled knowledge. So, please do it safely and I enjoy your video from U.K

[@kryzantem]

Thanks a lot for this, really cool explaination ! Quick question: Don't we have a simple equivalent factor between R600a and R134a ? Basically we are not extending or shortening the length pipes significatively so why can't we just use "original manufacturer R134a weight" X (standard_equivalent_factor) ? Cheers !

[@app213]

How do you match the new compressor for the fridge? With compressor's rated watts (cooling capacity)?

[@DandyDon1]

I hope this variable speed compressor is better than the one LG manufactures, as they are still having problems with them failing.

[@VooDooV6]

Have you ever thought of converting to an old school 134a compressor,,relay start....these lg Compressors are shit😂

[@TodoFrigorista]

Saludos cordiales desde Argentina

[@kreyolappliance1469]

The inverter need operating voltage and control voltage. Would you share how you wire the inverter.

[@waltahlgrim5508]

I do not believe the compressor installed was truly an inverter compressor as you are correct that an electronic driver board would be required. It is also funny how the 134A simply disappeared out of the system when I blinked.

[@MyGoogleYoutube]

Is there any point to flowing nitrogen through the system while you braze? Can you ?

[@andrewgray1949]

2:01 It is not legal to discharge the refrigerant to the atmosphere in most countries ! Replacing R134 with R600 is not environmentally friendly unless you pump the old gas into a cylinder for disposal. In the US, illegal since 1995, the fine is upto $37,000 and there may also be a bounty of upto $10,000 for reporting the offence Your KZbin appears to say United States...

[@joeabad5908]

This dude know what he is going.. Appreciate your efforts in sharing us this video.

[@forevertechenglish]

I appreciate that!

[@mrgcav]

No he is wreckless and dangerous. He built a bomb.

[@johnpavan6431]

wrong...not supposed to vent refrigerant to the atmosphere. This guy should be fired.

[@MrJugNut]

OMG the amount of dust in that fridge is totally off the charts. I cleaned out my desktop gaming PC after 2 years of daily use & it had only a fraction of the dust that fridge had.

[@aleksandersats9577]

No he does not. Dude let straight up refrigerant into the atmosphere...

[@امجدصوافطة]

اشكرك مهندس لكن لم يتم عمل إعاقة لفريون 600 ما السبب ؟ام أن إعاقته هي نفس إعاقة 134؟

[@mohamedomara8631]

انك مبدع حقا استمر فنحن نتعلم منك الكثير 🤍

[@jensschroder8214]

because the metric system and Celsius is used and also Indian plugs ( 226 Volt 50 Hz) it was not filmed in the US

[@forevertechenglish]

I give Heat To every comment is because I appreciate their opinions too.

[@forevertechenglish]

Here I Go I gave to yours as well.

[@jensschroder8214]

8:18 It is from either India or Pakistan.

[@mazharaltaf4899]

Very well explained. Thanks

[@forevertechenglish]

Glad it was helpful!

[@kareemhameed4042]

Is the change compressor a higher one or the same 1/6 of the danfoss?

[@allezvenga7617]

Thanks for your sharing

[@rolanddejesus8685]

thank you very much sir for sharing,God bless.

[@forevertechenglish]

You are very welcome

[@liv7680]

A bit more info about wiring specifically how do you control the temperature inside the compartments. Did the new compressor come with a control board? Im looking to restore a very old fridge but haven gotten to it due to high power consumption of the old compressor. I'd like to upgrade to an inverter. Thanks

[@un65tube]

Good explanation! Thank you. Would be good if there would be a way to prevent the old gas from escaping to the atmosphere as ist is hazardous for the environment. Greetings from Germany.

[@zodiacfml]

nice video clips, showing well what is going on. the narration/translation is also very good! the technical skill of the person is also good. i'm impressed with this video which appears to come from Pakistan, if I'm not mistaken.

[@manu_thind]

Compressor is continuously running auto cut off don't work , what could be the problem ?

[@forevertechenglish]

Check whether thermostat is fine or not. If it goes bad, the compressor will not trip.

[@manu_thind]

@@forevertechenglish thanks appreciated

[@robertonicolosipiva2646]

Que serviço de primeira congratulations from Brazil

[@forevertechenglish]

Obrigado

[@alieshghi6743]

Very instructional video. Very well done. Sir, about charging the system would have a different way so we dont have to wait this long? In our field, we cant spend so much time on one call. Thank you

[@vWhiz]

Amazing explanation and hand work. Thanks for this informative post.

[@toddt6730]

Very talented

[@yngndrw.]

I'm curious as to why you cut off the service valve and brazed it shut - Why did you not leave it on for ease of future servicing and save yourself the effort while you're at it?

[@forevertechenglish]

I did it to make the refrigerator look like original.

[@forevertechenglish]

As like the company.

[@yngndrw.]

@@forevertechenglish Ah I understand, thank you.

[@wanderlimacoutinho4487]

Curiosamente aqui no Brasil estamos fazendo o inverso retirando o compressor r600 e substituindo pelo r134a por motivo do compressor r600 travar muito em pouco tempo. Agora por curiosidade esse embraco é fabricação aqui do Brasil?

[@forevertechenglish]

Oh, que interessante saber, você remove o compressor inverter r600a ou o compressor normal? Pois instalei um compressor inverter r600a da embraco, que está funcionando que nem uma fera nessa geladeira. Não sei onde é fabricado o compressor.

[@joels7605]

Excellent work. Where did you get the compressor and inverter to drive the compressor?

[@forevertechenglish]

I got it from a local compressor vendor

[@andreasmoll_0924]

Why did you remove the valve and solder it again?

[@roco9063]

R134a has an gwp of 1430. 3,50kg of r134a is equivalent to 5t of co2 👌 A car dose 380 kg of co2 in one year

[@lyrapkfvl4374]

more globe warming I don't think there's that much in it. So he only filled it with 80g of R600 maybe a double or tripper would have been there. think 200-300g r134a (my car only contains 700g r134a)

[@forevertechenglish]

@@lyrapkfvl4374 This fridge contained only 150g I think.

[@mrgcav]

DO NOT EVER DO THIS CONVERSION. OLD refrigerators Pre 1997, are Safer and more efficient than new refrigerators. Most new refrigerators are junk that only last 2-4 years. You do not use an infra red temperature sensor to measure temperature readings in a refrigerator, unless you want inaccurate readings. You must measure the air temperature of the air blown off the evaporator in the warmest part of the refrigerator, which is usually inside the door. You need a thermometer that records the highest and lowest temperatures over time, typically three full cycles of the compressor after reaching the desired temperate setting zone. I call BS. You are totally wrong. Now in my professional 35 tears of servicing refrigerators, opinion, changing from R134A to R600 is a big mistake. R600 is 7°C warmer than R134 thus it is a less efficient refrigerant. R600 is NOT Eco Friendly either. Granted it is slightly more Eco friendly than R134a. Both are Toxic to humans and the environment. R600 is Isobutane. Yes BUTANE, as in the flammable liquid in butane lighters. This is because the EPA is phasing our safer Nonflammable R134A like they have R12. (R12 Was the best most efficient refrigerant ever invented.) R12 refrigerators has a 80/20 duty cycle meaning the compressors were usually off 80% of the time. R134A Systems have a 35/65 Duty cycle. R600 Systems have a 48/52 Duty cycle. Meaning the compressors run more often and are more noisy and are much less efficient than R134A systems. Plus with a longer duty cycle they use more energy. WHO WANTS that ??? Plus the inverter boards fail at $300.00 and up. This is our government trying to protect us. STUPID. NOW I dare anyone to tell me it is a great idea to heat up and compress a flammable gas. Then put it in residential homes. What you have here is the potential for an explosion. It has happened. QUESTION: What goes "BOOM" in the middle of the night ? A R600 refrigerator! Fortunately R600 is very corrosive and it destroys the seals in the compressor, so the compressor will fail. Just ask LG, Samsung and Whirlpool. They all are having R600 Compressor failures within two years. If you need a refrigerator buy an old one. The older the better. I will NEVER put a R600, R400 or any flammable gas refrigerator in my home. I am sticking with R134.

[@arianbia7777]

awesome bro! i wish i could do the same here in Indonesia

[@TheBlairHouseProject]

Please add more detail on the differences in the drier/why you are changing it, where and how you purchased the compressor/drier, what tools you are using. what kind of torch, type of flux and solder, how to safely use the compressed nitrogen, etc. Perhaps a video especially for that?

[@Tosheto666]

great video again mate , thank you for the knowledge

[@forevertechenglish]

Thanks

[@AFTABAHMED41]

hi, is it same size of the capillary tube for refrigerant R134a or the different size of R600a ?

[@forevertechenglish]

I have used the same capillary.

[@aditiyaputra9864]

Ini sih bukan kompressor inverter

[@aditiyaputra9864]

Kompressor 220v...tapi pakai R600@

[@anthonyfindlay466]

You need a nitrogen gas regulator, but you still did a fairly good job.

[@forevertechenglish]

Thank you

[@avnerabulash]

There are no subtitles in Hebrew.

[@gpsfleetmatic]

You might require a regulator and pressure guage to be able to show the pressure supplied to the system, something around 15-18 PSI should do

[@kareemhameed4042]

@@gpsfleetmatic only industries na em dey use this nitrogen flush system. For naija here, we make use of cooking gas (LPG) very good than nitrogen.

[@gpsfleetmatic]

@@kareemhameed4042 you mean use LPG for flushing? I never tried that, I use Nitrogen, I only use LPG + Oxygen for the brazing. LPG is highly flammable and high risk. I know of using Paint Thinners for flushing as well

[@Flip-Flop-Rio]

Ela fica mais economica em ralação a gasto de energia?

[@forevertechenglish]

Yep, because it consumes less energy then a conventional compressor, and is variable

[@pirelli77]

Very interesting vids! Thanks! ☺👍

[@masttt8480]

I would like to know how you connected the inverter compressor to a regular 220v source?

[@kareemhameed4042]

The PCB board converts it.

[@elchakajimenez7946]

I need to pc board

[@atuldhoundiyal6475]

Does the old compressor was invertor?

[@forevertechenglish]

No it was not..

[@georgetsetsakos6088]

love the smell of vented refrigerant! YUM. Very entertaining vid!

[@forevertechenglish]

Thank you 😋

[@KhuramTanoli-v8x]

I installed this but now compressor is continuously running and do not goes off after achieving cooling. Why thermostat is not working to shut compressor off. Please suggest

[@forevertechenglish]

Inverter Compressor do not shut down untill, i will talk about it later, It maintains the cooling at a very low amperes, It mainly prevents that initial heavy torque which consumes alot of power by a normal compressor and makes the units on energy meter to rise instantly. It will keep working Until It senses that Cooling inside the refrigerator is up to the mark, do check its thermostat and also check what temperature you have set it on.

[@KhuramTanoli-v8x]

@@forevertechenglish it's thermostate setting is at 4

[@kareemhameed4042]

How are you and how's the family, sir? I have a question sir, I want to change a compressor which is an R12 to R134a of the same compressor size of 1/5HP. The former technician that install the former compressor added a 1/10 condenser hereby he disconnected the inner condenser from the outside one. I am thinking sir, since R134a has a higher condensing power than an R12 would you advice if I remove the 1/10 condenser and replace it with a 1/8 or 1/6 condenser sir. It's a one-door freezer-fridge. Or I should use the condenser and add a cooler fan? Thank you sir, as I await your response.

[@forevertechenglish]

Sorry Saw your comment today was busy. In your case, the former technician added a 1/10 condenser to compensate for the change in refrigerant. However, simply changing the condenser size may not be sufficient to ensure optimal performance. It's recommended to consult the manufacturer's guidelines or technical specifications for your specific freezer-fridge model to determine the appropriate condenser size for R134a.Removing the 1/10 condenser and replacing it with a larger condenser such as a 1/8 or 1/6 could potentially help improve the system's efficiency. However, it's crucial to ensure that the new condenser is compatible with your system and that it can be properly installed without causing any issues with airflow or space constraints.adding a cooling fan to the condenser can help improve the heat dissipation process and enhance the system's overall performance. A fan can increase the airflow across the condenser, assisting in heat transfer and maintaining lower condensing temperatures. This can be particularly beneficial when using R134a, as it operates at higher pressures and temperatures compared to R12.

[@forevertechenglish]

See the technical specification sticker on your refrigerator.

[@ajayrathod9804]

Thank you🙏 nicely explain.

[@liviuion9651]

Remember when i asked You about noisy inverter compresor?i have changed the charge with a new one(r600a).Now the compresor îs silent.I will check further about a moisture issue in the sistem.Have a Nice dau!

[@kareemhameed4042]

Did you charge the refrigerant in liquid or gas?

[@forevertechenglish]

Gas

[@kareemhameed4042]

@@forevertechenglish I was one of your video, where you said R600a should be charged in liquid why is that?

[@firasbachour7325]

Had you ever replace a constant speed compressor with an inverter one with all electrical and control circuit?

[@KLKD12484]

Can we fit this compressor in AC and work

[@williambrennan5701]

I literally do the opposite here in the United States and replace r600a with 134a. I'm thinking about using r401a (yes 401 not 410) It was made as a replacement for r12 . R12 is about 30% more efficient than r134a so that should lower head pressure.

[@jaybird7534]

After frig compartment meets 34 degrees do a frost-line adjustment charge on all small converted critical-charge cap-tube systems needing more or less gas than data plate indicates.

[@goldencrownmotors5225]

Why did you change it to r600a.. Is R600a inverter compressor? I head r134a is fast cooling than R600a.... Because am planing to change my r600a compressor to r134a, compressor to my chest freezer... Pls advice

[@TheDirtyChef]

Shouldnt you purge the valve after you puncture it and before you connect it to the system? Seems like there could be some air contamination in there.

[@carsonsmith5871]

Can you explain how you are controlling the inverter compressor on the old refrigerator?

[@forevertechenglish]

It has a control board, install externally with it.

[@omidamiry4109]

In this convert we must remove the thermostat and replace the sensors for controlling?

[@laythmajeed3129]

Did you change the capillary tube size?

[@kaanerdem2822]

A month ago, i changed my refrigirator setting from minimum to max. After a day or two, my wife booked a last minute ticket and we went on vacation for a week, then i changed it back to minimum. After we came i check the frig and inside was a bit icy as if he stood on max settings, today its 3 weeks and its still like that. The frig is too cold how do i fix this?

[@frk380]

Great job

[@huynhuc556]

Mình chỉ góp ý. Bạn sử dụng vải sợi carbon để hàn các góc dễ hơn nhé... Vải carbon sợi thủy tinh không bị cháy khi gặp nhiệt độ cao

[@forevertechenglish]

Vâng, đó là một gợi ý tốt.

[@DREAM-GUYS]

How we can identify this is inverter Compressor, and how to check continuity of inverter Compressor and non inverter Compressor

[@hannes8004]

what is the solder stick you use? is it normal solder or a spezial thing?

[@Jan-r6o6x]

It is Silfoss , usually 15% silver and various alloys. No flux is requires.

[@mbahcarrier1629]

👍👍👍👍... Pekalongan, Jawa Tengah, Indonesia 🙏

[@Baiev]

Embraco, That's a Brazilian Compressor...👏🏻👏🏻

[@jameswatters9592]

Do you think the mass of flies might have had anything to do with it not working

[@forevertechenglish]

Nope! the flies came in after it got bad.

[@s58015]

Eu tenho um freezer antigo da Electrolux sera que consigo trocar o motor dele pra inverter ?

[@shindvs]

What about compressor electrical connection Is it single phase motor normal start and run coil and PTC overload relay protection ?

[@forevertechenglish]

I have a separate video on it, types of inverter refrigerator compressor control

[@jay1st1st]

is it legal to use R600A in house utilities as it's highly flammable ?

[@forevertechenglish]

Many companies uses r600a refrigerant in refrigerator, Because due to it highly good cooling properties, Also its eco friendly.

[@jay1st1st]

@@forevertechenglish tnx it's very informative

[@pluce1000]

Best video ever

[@EJEuth]

That final part, about condenser length and refrigerant type (and their boiling points) you mentioned at the end is not clear to me. Maybe you could prepare another video about these fluid conversions and the impact their properties could have inter original installation. Thank you!

[@muhammadshahin3056]

Which Meter did you used to measuring live voltage,current..

[@mtay65]

Great vid.