I would he very happy if you could explain how we run the Cf02d01 Ves motor board
@TOMTOM-nh3nl Жыл бұрын
Thank You
@forevertechenglish Жыл бұрын
You're welcome
@teodoromaria7 ай бұрын
Hello sir, What type of starter is used in the VCC3 2456 PL F 08 compressor?
@أفكاروأبتكارات-خ1د4 ай бұрын
How are you sir? I have a board similar to what you have, and there is a fault in the resistors of the microcontroller. Can you help me? I want a clear picture of the board so that I can determine the values of the burnt resistors. Thank you.
@sergiorau60097 ай бұрын
Hi Coul I replace a defective Embraco VCC3 2456 80F 14 Imput 220-240V 2.1A Output 230V 53 a 133Hz 3.3A for a similar one, but instead of 53 a 133hz, it is to 150? New one avalable is Embraco VCC3 2456 28 A 19 Imput 220-240V 2.1A Output 230V 53 a 115Hz 3.3A.
@forevertechenglish7 ай бұрын
For that check the hertz on your compressor, The lowest and the max hertz. If is in between the replacement board. You can replace it.
@sergiorau60097 ай бұрын
@@forevertechenglish thank you very much! Compressor is 53TO133Hz, inside. Very usefull you vídeo! Congratulations from Brazil!
@sergiorau60097 ай бұрын
@@forevertechenglish What I discovered after purchasing the board is that it is not enough for them to have the same input and output values, we need to know whether the board is "drop in" or "Frequency". In this case, I purchased a "drop in" inverter board and the compressor did not start.
@th69i2 ай бұрын
It's not the other way arround ? P = Phase (Live) and N = Neutral ?
@mrheart11395 ай бұрын
What if no voltage in UVW what is the possible problem?
@forevertechenglish5 ай бұрын
Then, its possible any Igbt is bad, Or any thing around the circuit is bad, which need to be checked and addressed.
@nguyenson3112 Жыл бұрын
Dear Sirs, I have a problem with my refrigerator inverter, blinking 9 times. Can you explain about Jiaxipera inverter circuit?
@forevertechenglish Жыл бұрын
If I get one sure I will explain.
@pasqualegalasso5153 Жыл бұрын
Ciao, che valore ha il fusibile collegato dopo agli IGBT?
@lords98352 ай бұрын
I would really like to take a course from you in Brazilian Portuguese. I would definitely buy it! I have a question, I would like to know the reference of these drivers that control the IGBT.
@ugwuchinonsodaniel5866 Жыл бұрын
Hello sir...I have problem with my inverter double door freezer the indictor light is show but the compressor can not start at all I have the picture of the panel how I can show it to you pls
@ChhaiPech Жыл бұрын
thaks for this video,sir
@forevertechenglish Жыл бұрын
Most welcome
@galegagi8 ай бұрын
Thank you for everything you do I have a question and I would be very grateful if you could answer me In the large black capacitor, I get 311 volts, you said it should be 320 to 340, is the lower voltage in my case causing it to malfunction?
@forevertechenglish8 ай бұрын
311 are also fine. Its no issue. What the problem with yours?
@galegagi8 ай бұрын
The test on the compressor is okay (the resistance between all 3 contacts is the same), also on the inverter board everything looks okay but the compressor still does not work
@galegagi8 ай бұрын
l still looking for a solution. Thank you for your quick reply
@guilopur10 ай бұрын
Are the follow up video posted?
@forevertechenglish10 ай бұрын
Yep visit my channel I have them
@aziz112233445566 Жыл бұрын
hi i am not get 320 v dc on capacitor
@JuanCarlosViellar8 ай бұрын
Thanks
@rooblemax1118 Жыл бұрын
how to made refrigerator deep freeze copper pipe coil roll
@mohamedyassinegarreb3412 ай бұрын
Good
@JohnnyAtlas9 ай бұрын
Removed from working fridge did your jumper trick 1&2 but I use 120vac and it will not work. Great video but my luck is terrible
@lumenlamela6829Ай бұрын
Sa an puede Maka buy ka motor
@سعيدمحمدسليمان-ط9ب Жыл бұрын
الترجمه بالعربي كبيره جدا ومش ظاهرة الكارته وانت تشرح انقص حجم الترجمة حتي نشوف الشرح على البورد الإلكترونية
@Tayeb_Aic Жыл бұрын
السلام عليكم حجم الخط تستطيع التحكم فيه من الاعدادات عندك
@BilalTwijarАй бұрын
Tiklojya❤
@mdajemkhan2935 Жыл бұрын
this video toking to you hindi dubbing dir please 🥺