FORGOTTEN Chevy C10 ENGINE Might Be BLOWN?

[@JD_JoyrideTV]

What do we swap into the 63 c10?

[@daveprostock2622]

JD JoyrideTV a turbo V6 out of a Grand National or T type!👍🏻

[@mattpinckney3923]

Stock as cock. Dont make it a monypit

[@stevec7819]

ecotec

[@elijahcampbell6347]

Chevy 283 v8 you wont be sorry

[@timlinder7894]

Well you already said ls go with a ls3 or higher with twin turbos I know you already heard me say that before or go with the 454 with a 400 turbo transmission and twin turbos

[@tyg3rpro]

I would actually prefer to see that I6 brought back to life since it does still run

[@gertraba4484]

YEAH FOR NOW . sounds like a bad coil points, condenser, ign switch, wiring harness, bought all those 6cyl parts why not use the truck for awaile as is????????????? had same prob with 6cyl GMC cutting out at speed it was a bad wire going to the 12v on the coil looked ok but was onlly holding on by one strand........................................

[@pathbelow6652]

These kids don't know enough about a simple set up. They complicate it. That inline 6 is cool. They run on and on. These old setups are for the farm use. This kid wants to put a v8 w fuel injection and on and on. He wants a street rod. Today's youth likes to complicate. Simple they don't understand. So just do it. Change it. Shut up and do it.

[@BuzzjoyV7]

fix the 6 when you rebuild it mid rang cam and a 2barrel carb

[@keithgrauherr2245]

And electronic ignition and a set of six cylinder headers with dual exhaust!

[@greasy8eyes]

and a 5 speed out of a s10 or camaro v6 and some 3.20s gears

[@gertraba4484]

@@greasy8eyes 4 speed with floor shift hurst

[@wayneh3021]

Build up that old girls heart an make her old school blown, that motor is tougher than most v6s, just my thoughs 🤜🤛👊👊

[@Kodiak660]

Fix the 6, you will learn a lot.

[@mqa1963]

i think he needs to fix it also.. he needs to learn to repair engines.

[@kevincornell1439]

totally agree if he cant get that inline 6 going how is he ever going to ever get threw a engine swap. hell if he can upload onto youtube he sure can watch the thousands of videos to help get this old girl running right.

[@CenterStarsChannel]

@JD JoyrideTV When you jumped in and started the diesel my heart jumped. Those thing's have glow plugs. That means key on for ten seconds or so and it will fire up. Diesel runs off compression and the glow plugs pre heat thing's to get it going. Also with a turbo to extend the life of it, it is best to park and let the vehicle idle for exactly no less than 1 minute to let the turbo cool so you don't cake the oil lines with burned up oil. I just found your channel. Figured I would let you know just in case.

[@thomaspeplinski6618]

You can drop any of those older motors in there they will fit. I did an old panet truck from six cylinder to a 283. Just needed to do was upgrade radiator.

[@gertraba4484]

motor mounts and fan plus a bigger rad, he shoulda ordered the 8cyl rad knowing he was going to swap the motor

[@ladypilliwick8179]

I pulled a C-10. 1983 Silverado. Out of field. V8. Love it. On the window. The power runs though the switch on the steering column. They have wiring kits that by passes the colum. Good luck.

[@justinhobart8747]

If I was his wife, I'll be out in the garage tonight with a Chilton repair manual, and a wrench. Then turn the key when he wakes up and say... " it's done! " 😉

[@hgbeat]

Before you do anyting, confirm that that engine is no good. It could be a number of different things that would cause the starting problem that you described.

[@billschey4753]

Rebuild the six, torque cam, pistons, 2 barrel manifold, Lose the points and condenser and install an Electronic ignition, split manifold with dual exhaust, four speed trans or five speed, rebuild it yourself and have fun with it. Easy motor to work on. With the three speed you may have some decent rear gears maybe even 4:11’s. Nice rims and tires will make it drive a lot better.

[@mechaniccaleb9315]

Been watching for a long time, when it was mostly GT500 content, just wanted to say I'm glad to see a "Mustang Channel" branch out and do more than just Mustangs. Enjoying the content with the classics variety. I've got a Mustang I'm building as well as 3 classics, keep the great content coming.

[@patbradley916]

You want to do something different? look into swapping in a souped up 292 straight six

[@Cartier_specialist]

Just get the stock engine running right. That engine is the same engine used in the 1953 and 1954 Corvettes so it's certainly good enough for a farm truck.

[@ianpurkis3925]

Have you seen Vice grip garage? He’s got a sweet c10!

[@AndersonMedia]

Im kinda torn on what to do on that. Id love to see the old motor brought back to life. I also think a new motor would be good too. Less worries with new engine. Look forward to seeing the work done in it.

[@keithsims86]

I got a slant 6 Duster i bought for $600 it sat up for 36yrs. I got it running pour oil through spark plugs holes to get compression up and it started up.

[@mromatic17]

Swap in a built ford 302 windsor! everyone and their mom swapps ls engines swap a 302! i have one in my 1994 f-150 4x4 5 speed and i get up to 20mpg with it! I like that your wife likes the patina look on these old trucks! it shows she appreciates the history and the truck for what it is!

[@09R1ms3]

Fix the Six!!

[@bartscanland9415]

Check your fuel filter (again). Old fuel system may have junk in it (still).

[@Jw_01]

I love Laura she is so much fun to watch

[@harrypotterification]

If you can help it, I would keep its original engine. Those little in-line 6 engines are rock solid, and if you fix it up and take good care of it , it will last you forever. That truck will make a nice cruiser for those date nights.

[@lewiscurnutte1272]

Can't wait to see whats in store for the truck JD. 😀

[@dennisthespeedmenace7530]

Jd any truck of that era is going to need a motor swap and yeah they are money pits until you have replaced everything over a 3 year period! The bonus of this is you put what you want in it!

[@troysgarage]

She was NOT impressed! LOL. My wife gives me the same look when I try to justify me truck part purchases! Hahaha

[@zachswanson5622]

I think you should relocate the shifter to the floor instead of on the Coelom for these reasons one so you know where all of the gears are located and I would just put in a 4 speed since you said the c-10 is a budget build two if you want you can get a shift knob diagram if I believe because my dad had a 70 c-10 and reverse was all the way to the right and down two it’s self explanatory instead of the column shifter is a guessing game and it makes sense to get a rebuilt transmission for the 350 which is a 4 speed factory

[@thunderjet4294]

Should do a big block swap on it bro junkyard BBC s are like 650 around my area 850 with a trams

[@Averagegunenthusiast]

A 96 and up vortech 350 with a cam and intake swap would probably be the best bang for buck swap. Stock vortech heads will support 400hp from a 350.

[@landonreynolds1409]

You need to find a stock 5.3 truck engine and put a turbo 350 transmission adapter and if you want more you can get a can or a set of heads

[@snoobiedoo6705]

If it shuts off after initial warm up then it's your coil also check your points if it has points check to see if there's any corrosion on your points and if it's worth saving clean the points then set the gap personal opinion everybody wants a V8 but you can build that inline 6 to be pretty spunky not to mention it would be something different to look at when you take it to a car show and you can actually build that six on a good budget.

[@snoobiedoo6705]

PS I don't know if you know anything about classic or antique cars try pouring some gas out of the carburetor if she fires your fuel pump is bad. And if you have not changed your spark plugs pull them out and see if they have been filed they may need to be cleaned or replaced

[@raybirsic6058]

his wife is a real ball of fire !

[@Steven-jq2yz]

Your c-10 is the right year, I think it's a 292. 63 was the first year for those. Mid level cam, bore the block 60 over, new intake manifold and a 600 com carb and it'll run like a scalded cat.

[@greasy8eyes]

i thought it was a 230 ci inline 6 myself i could be wrong.

[@graememorrison5456]

What a awesome family love these videos keep them coming 🙏 Greetings from Scotland 🏴󠁧󠁢󠁳󠁣󠁴󠁿

[@peterjones8324]

Definitely would be cool to see the back story of the C10. I can't wait.

[@Tom-cy5em]

How about a sleeper with a old school 454 and M22 Muncie 4spd like out of a 70 chevelle SS with a big lumpy cam headers, hi rise holly with a 356 rear end gear.

[@pocket308]

Check your point again your truck is 12v but the coil run on 6 v you need a resister wire on the coil check your spark again.Tony

[@greasy8eyes]

Head gasket set for a 230 thats basicly the top end gaskit kit for 55 bucks and a day for a first timer taking there time from start to finish.

[@BigSalP]

Is the engine in your truck a 292ci ??? If so I may be interested in taking it if you're going to do an LS Swap.

[@ericdolan2130]

"The engine won't start Babe"...He said with the coil wire disconnected.

[@gertraba4484]

he took thepoints out tooooo

[@dustinjenkins1709]

When carbureted engines act like they don't want to start or are flooded hold the gas to the floor while cranking the engine. It helps.

[@JD_JoyrideTV]

Dustin Jenkins I tried that and still nothing.

[@kevinsukdolak5007]

There's nothing wrong with his six...he just wants another motor...lol. He's young though...if he gets what he wants you know mama will too...he's going to learn....mwa haha

[@scamp7441]

That's what I was thinking. He probably pulled the coil wire so it wouldn't start in front of her. Lol

[@gertraba4484]

yeah click bait, sounds like he wants to do the swap but I hope he don't butcher it up and abandon the project

[@skarekr0w3]

My thoughts exactly. I don't hear spark. Coil, plugs, points, distributor... I would be looking at that. It did run, it doesn't run now, it sounded acceptable... I think he wants to build the truck. I'm no mechanic, but I've brought a few things back to life. Hondas, VWs Fords and Chevys. I own a wrecker, so I I've dragged a few things home to play with. I was more concerned with the clutch and trans. But it is a 3 on the tree, and I've never driven one. It's a whole different animal. Unless there's water in the oil, or oil in the water.... I don't even see any evidence of a vacuum leak. It could be a carb issue. I don't hear it firing. I would investigate these things first, save my money on other things it needs. So far as I can see that engine is fine. It ran. But I don't hear spark.

[@gertraba4484]

@@skarekr0w3 I think it's DRIVER CHANGITIS the MOTOR saying it's NO GOOD to WIFEY....... to get her on board he's gonna trash a perfectly good motor oh well HAPPY WIFE... DON"T GET MARRIED!!!!!!

[@skarekr0w3]

@@gertraba4484 LOL! YUP! It's all about the wife... I just don't think he realizes how cool the truck is just like it is. I love old stuff. That engine is a classic all by it's self. I'll take 1960's over 2019's any day! They just don't build them like that anymore, and they are on the endangered species list. If replacing the engine is the only way, then do it. But if the engine is not sick... Let the truck be who she is meant to be. I would love that truck just as she sits.

[@peapodamoose]

Always a 👍. Love this channel.

[@Jaybear669]

Man up and keep it stock like your wife wants! lol

[@paulmills426]

You should do a LS swap or Coyote would be cool as well. LS would probably be the way to go for a budget build though. Find a good junk yard motor.

[@tylerharkness4964]

Just get a old Chevy 400 small block stroked out. I swapped my stroker motor into my 88 cutlass lol

[@RedEyedPatriot]

I've got a 60 apache 20 stake bed with a cammed 235i6 with split manifolds 4speed

[@JD_JoyrideTV]

Michael Craig Broughton that’s so badass

[@RedEyedPatriot]

@@JD_JoyrideTV got 5squares too😎 and a 60 c50 Viking....loves these old trucks man

[@dickiecornwell7262]

Do the 6 spilt manifold 2 4s one cam set or 410s have something different old school nice video's i like my fords but old classics I like them all

[@willie6185]

If it was a head gasket you would have water in your oil. You need to adjust your carburetor and set the gap in your points and set your timing. Chilton or Hanes auto repair Manuel’s can help you with that or you tube videos

[@fishbone856]

Nothing wrong with that motor. Just lack of experience or spark..try putting the coil wire back on.

[@hellzsniperII]

just do a small block chev like a 283 or 327 keep it nice and drivable to have fun with and enjoy and you don't have a pile of money stuck in it and it would be period correct and cheap to build.

[@Nowehi305]

The engine good you need to change the Delco and carburetor or fix it believe me it will be working very good👍

[@79tazman]

Those straight 6 engines are very reliable when everything is running right you may need to rebuild the carb a rebuild kit is cheap and it's really easy to do

[@79kevman]

He put a new carb on it

[@r1powerburn]

Put a push rod 5.0 in that truck. With the t5 trans, and a tall shift stick,

[@jamesbethel5170]

Keep the 6cyl in the truck just put a head gasket on it,it easy give us more intro the 3speed trans is one of Chevy strong trans

[@daveprostock2622]

Be cool to hear Susan’s story about the C-10. Chevy Tom said he would split the profits on the vette with you! Yeeeeeeeaaaaaaaaah Chevy Tom!😆✌🏻

[@JD_JoyrideTV]

Dave Prostock he was just talking. He’s not splitting any profit.

[@dannygore5186]

Any sbc would be good for driver they are getting super cheap arround me because everyone wants an ls

[@larryboydjr7461]

JD I love your Chanel keep them coming

[@JD_JoyrideTV]

Larry Boyd jr thanks for the LUV ❤️

[@joshuapalacio6047]

I wish there was that many car shows here in Texas

[@Reject06]

theres like a car meet almost every other night! lol iunno where you looking but they are popping up all the time

[@joshuapalacio6047]

@@Reject06 I live in lampasas Tx it's about 1hr from Austin and 3 hrs from Dallas

[@an_auto_addiction5742]

Still love those cobra seats

[@awesomeparker5991]

What is the thing on his wheel of his truck

[@pedroguerrero7718]

it's need a swap for sure and man i just love the look of your wife when you say that you need a engine Lol...

[@terrylawrence6772]

Again, just give that c-10 to Tom !

[@JD_JoyrideTV]

Terry Lawrence lol he would love that.

[@b61mackman2]

Terry Lawrence I would love to have it. This is a fun project

[@briangoudreau5793]

Laura has great taste loves the patina #teamlaura

[@kjartanarnarson5302]

But to burst your bubble but if the 350 you gett stops runing are you going to change the moter each time if I was starting upp i Wild start by learning on this moter to learn it's as simple as it gets. but on other notes Chang it to v8.

[@saleendriver]

I think a Ford motor needs to go into the truck as revenge for all the people defiling Mustangs with chevy motors.

[@mromatic17]

Swap in a 302 windsor or a 300 I6 that would be bad ass and different!

[@jhutch1470]

Do a 454 swap. Plenty around.

[@svtk0310]

Cool ass truck!!👍

[@xxdrippyjayxx5860]

Can y put a big cam in the c10

[@adriantomlin2902]

It's not done man. You have a fuel problem! Start at the tank and work towards the carb.

[@kodiebelcher9191]

I thought the cobra was supposed to be a project car as well and nothings really been done besides wheels and seats?

[@thomashixson8572]

I saw a 350 w/ the th350 trans for 600 in Arkansas on craigslist

[@JD_JoyrideTV]

thomas hixson that’s a good deal and a hike for me.

[@michaelstapleton5510]

check your coil that the way they do befor they go out

[@rontownsend8235]

Electricity, with it they do not run. Replace the point lead from the coil.

[@xmcx7021]

Put a budget 305 or 350 in it. Cheap and dependable

[@alanwilliamson9350]

I dont think that 6 is done. Sounds like a fuel issue more than a bad motor. Picking up some trash out of the tank maybe.

[@michaelyeaple8468]

That truck is nice 👌

[@bradlujan6537]

“Keep it a budget build” “Let’s bag it”

[@0oChugChug0o]

Sweet love the truck brother !

[@DIPOUTDOORSTV]

I would go with a blown 502 with a 2 speed poweglide

[@johnkirby6216]

I think your ballast resistor a shot

[@SteveP-vm1uc]

Less than 100 bucks in parts and that motor will run like brand new.

[@stephenwebber3076]

Keep the 6!

[@MorbidThrasher666]

Its done!

[@danielortegawilson4173]

She not done motor not gone think u miss something

[@JD_JoyrideTV]

Daniel Ortega wilson exactly what Laura said

[@TheMick26]

Hey JD.🖐 That car show had a pretty solid turnout and had some nice cars. I agree, that ol' patina C10 was pretty cool. About your '63 Chevy, yep... she's done! The motor's done. Laura said "Done what?"😂 haha, I lost it! Laura ain't convinced, JD. I loved your accent at 7:33 .😅 Then your Ford took a crazy long time to start. Been hanging 'round that Chevy too long.😜 That was very nice of Susan to let you have another walk thru and gather more parts. Wow... you just don't realize how huge those old truck fenders are until you see them being carried on someone's shoulders. Honestly, I think that old engine still has life left in it, but if you're set on a swap, LS is probably the best option. See you on the next one, bud.✌

[@JD_JoyrideTV]

TheMick26 I feel like it still has some life to but I’d really like to swap it to something more fun.

[@TheMick26]

@@JD_JoyrideTV I'm onboard. Send it!👊

[@nova-ic7mw]

Any sbc will bolt right up

[@paulmingotti5589]

What about the El Camino? 😉

[@headphoneson4704]

Finally someone cares about my elcamino

[@kurtvara4918]

Wish I could send you a video I would send you one on my converted old truck.

[@JD_JoyrideTV]

Kurt Vara Facebook

[@raymondcoggins297]

Keep it gm

[@jeffreed2308]

how do i send you pic of my c10 and 350 i put in

[@JD_JoyrideTV]

jeff reed Facebook, JD JoyrideTV

[@roberttaylor9029]

Get ahold of texas speed they will hook you up

[@shoversracing1997]

Great Video JD and Drop a 302 or something down in it!

[@SchnelleKat]

Can anyone else imagine a GN Motor tuned and AWD? :O (Like on the Hoogian's 442 AWD)

[@jeramiakins6347]

spend a couple hours replacing the head gasket and drive it.

[@lathropgaines2018]

awesome video and update!!!!!! :)

[@TheSoulessdruid]

Barra swap JD, Barra the world. Keep the straight 6 look with LS power

[@carlosbishig1]

I liked it you videos and hello from Puerto Rico 🇵🇷 family

[@danielortegawilson4173]

Rebuild motor on c10

[@julioLopez-ur2pk]

Hey ,you could get cheap v8 from a newer Silverado