Freightliner Cascadia Shift Stalk Starter Blocked Error

[@christopherprofeta1095]

I was stuck in the middle of the freeway and this helped me start up my truck. thanks man you saved me

[@michaelburton24]

Thanks for posting this. I'm at arest area in Nebraska and mine done this. Cut the power and waited 5 min. Good to go now

[@ehsanallahmorad9556]

Thank you so much you saved me from middle of nowhere in AZ i unplugged those 2 little socket and everything is good 👍❤️❤️

[@NLD88000]

Thank you you saved me i was hooked to a 3 k run didn't want to losd it

[@polywoodtruckingllc]

9-20-23 & this video just got me moving thanks alot 😁🏆

[@j-flow617]

This video just saved my life!!! It’s 6-11-23 and this video helped me a lot. THANK YOU!

[@josephgardiner9866]

Not mine this is happening to me . I just ordered the new shift stalk . I'm hoping this will fix it.

[@j-flow617]

@@josephgardiner9866I don’t care the video helped me out when I need it. Good luck to you 😂

[@fernandoduran8156]

Where did you order from? Please add a link possibly pertaining number...thank you!

[@ariel9463]

bro you saved my life i was at a port and my truck would not start lol actual life saver

[@DoloGomez]

@@ariel9463 this just happened to me at a port! Lol first time ever.

[@britton6062]

You saved my ass this morning. Thank you sir !

[@martinezrudy62]

Thanks a lot for the info bro I can continue rolling now thanks to you

[@jaieshbaijal9125]

You Saved $$$$$$ and downtime. May God Bless you. May be while sleeping my hand touched the button and it was ON so turned off and disconnected and it fixed the big issue.

[@johnmabe3496]

Had this happen in a dock in Columbus, turned off power for 5 minutes and it started up. Got back to yard and company replaced the whole stalk and it happened again. Did the truck you showed and turned off main power for five minutes. Got it to start.

[@wolfsquared]

2024 Freightliner don't have that kill switch. Just tried helping a guy, 24000 miles on truck same issue. It eventually resolved itself after he was stuck in door 30 minutes

[@PensiveArchon]

This worked on a 2016 Freightliner as well, this is wild that this is part of the wiring scheme to block the starter, is switches in the sleeper ...

[@michaelchuwang3308]

I followed your steps and it worked for me, thanks for doing a good job 👍

[@ekoekokodoko7245]

You are a life saver bro.

[@uv163]

Also same warnings came out on my Cascadia while batteries haven’t hold the charge as they should so after few attempts to start the truck with jumpstart it kick out same sign. Been towed to dealer and while waiting in line decided to install new batteries and there’s a miracle - truck started with first attempt.

[@hektorian07]

@@uv163 it fix the problem?

[@Highway-Junkie]

Don’t know if this might help but I do not have a Killswitch on my 22 what I did do was put the key on the start position for five minutes turned it to the off position and started back up and it took away the stalk switch right errors

[@milk-gw2hs]

I unplugged the grey switch in my bunk cabinet and it started up. Plug it back in and I haven't seen the issue since but now I'm throwing a CEL a short time after the incident and I'm wondering if it's related

[@nukenridge4921]

2022 Cascadia Freightliner No communication between transmission to Ecm I got 12 volts on pin 21 and 23 two bottom pins no wires been cut so far harness is almost out right under firewall for now ,any ideas no click no start

[@jaswinder633]

You saved my life.. i was at where no road service thanks it works

[@jeremygall2164]

7/24 Hey, just used this video yesterday. Pulling those wires worked on clearing the code but it still wouldn't start and the code came back shortly after in my case. I ended up disconnecting/connecting the ground on batteries for a quicker power cycle and that did the trick. The starter activated but it needed a jump at that point which I had with me

[@jeromiebanks567]

Why does this happen?

[@Mrbrownstone1028]

Thanks man! Saved me some frustration

[@artme-v2b]

So what is the cause I just had same issue how do you fix so it doesn't come back

[@oumardiaby8342]

Thank dear! It worked perfectly for me. Thank you for saving my day

[@bowang6339]

I got the same problem, New freightliner I buy😀👏

[@DDTruckDriver]

Did it work?

[@ThePetersieklik]

You think the hard reset of battery (unconnect cables for 20 min will not remove the message?🙏

[@Lifeisaquicktrip]

Just reset you main power. Reset for 5 to 10 mins. Cycle the key 3 time the fourth start .

[@DDTruckDriver]

If it is just a glitch yes that will work, we talk about that in the video. But if it is an actual switch or other error you have to do other steps.

[@parvindertwinkle]

Same trick work for me. Did this code comeback for you after starting it like this?

[@restrepocluis]

did it came back tor you? It just happen to me today and I don't want to turn the truck off just in case it happens again

[@parvindertwinkle]

@@restrepocluis Yes, it happened to me again.

[@vfpaintjobs]

Will ot stop your accelerator from working ?

[@brunildamusollari9398]

@ddtruckdriver My 2019 Freightliner Cascadia truck turns on perfectly fine and drives . The message pops up and off while driving especially when I hit some bumps in the road/ or even when driving it shows up and then after 2 seconds it goes away the error message. Should I be concerned? Any suggestions, greatly appreciate your responses!

[@DDTruckDriver]

I think you are lucky and it is giving you a warning, yes I definitely think you should get it looked at.

[@bosskam200]

Just clean and tighten your battery's please

[@SergeyK-USA]

Have fld120 1991. And I’m happy no def no electronic on board no headache 😂

[@alyakuzminoff5354]

Thank you! It works perfectly!!

[@lurcha9036]

Wow thanks for the help I got it working.

[@restrepocluis]

Went to turn my truck on today to get going, this code came up I turn the kill switch off for 10-15 mins and it started after that. it did took me Liki 3 times for it to actually Start

[@HebrewJerusalemPrince777]

I tried this too when this happened and it didn’t work. What I did I have 2 keys the one in ignition was key copied. I took it out of the ignition and put the original key in and it started right up

[@ThePetersieklik]

My Freight liner Cascade 19 ‘battery died after jumping attempt the same error message popped up “starter blocked”any solution for this model?🙏

[@ericmendez5815]

Did you get a solution?

[@brandonsmith8924]

Just saved my life

[@alexhowley9834]

My truck is brand spanking new and keeps switching into neutral while im driving, mostly around gear 5. It will flash the gears at me and will not go into gear until i stop and switch from drive to neutral and back to drive.

[@scmarine843]

Did you ever find out what the problem was/is?

[@alexhowley9834]

@@scmarine843 adaptive transmission issue, computer needed to be "relearned" it's basically the transmission getting confused and throwing itself to neutral bc it tries to adapt to the way u drive

[@scmarine843]

@alexhowley9834 I appreciate the response. This just happened to mine last night, so we'll see if the actual issue is the same. We're out here confusing A.I. 😆

[@alexhowley9834]

@@scmarine843 😂 god damn technology. Make sure you tell them to "relearn" the tranny, try to get it to happen with them plugged in on a test drive. I had to go to 3 different shops before it got fixed. It's not a common issue. Good luck!

[@scmarine843]

@alexhowley9834 I appreciate the info and last question.. expensive?

[@crazyboy55789]

I have same problem my friend it's the starter you have to hit it with hummer it's on the top of the transmission

[@rajveersidhu6849]

Thanks for the help

[@gurpreetdhillon9517]

thank you buddy

[@fernandolopez9631]

Thankyou bro

[@alphahope7205]

Thanks, very helpful

[@meganrobanser1855]

Absolute life saver!!

[@u1s9e8r3]

It happened to me once. I'm Cut off power for 6 minutes it didn't work then i wait 10 minutes my truck started normal.

[@curiousTT]

yep this was helpful for me

[@Timmyboy2]

If I turn my key on and off a million times while trying to start it eventually starts

[@tyreemines9520]

Worked!!

[@TruckinWithTwo]

lol thanks man 😅

[@josephgardiner9866]

I'm going through this right now , nothing here is helpful, I believe that I forgot to take it out of nutreal and all the Air leaking out of my system has caused my problems. I left the truck in drive and it leaked all my air out so I can't put it back into netural so now because the truck is leaked almost the air it's not letting me start the truck.

[@ag8499]

👍

[@sergiobarajas7131]

Just buy a manual

[@Disciplesproctor]

Worked like a charm, thank you sir.🫡

[@iraklitabagua9866]

It was a big help, thanks!!