From the Concrete To The Trailer! /Boat Recovery!

[@peglegjim57]

Working as a Tech at a marina, I’ve done several of those recoveries, and there’s a much better way. Secure boat as they did, but then unhook the trailer from the truck, then crank the winch, which slides the trailer under the boat, without dragging the stern. Then just hook her back up, and drive off into the sunset.

[@TheBigDanShow]

How do you keep the trailer from running down the ramp?

[@peglegjim57]

@@TheBigDanShow The boat is secured by the wrecker, so it won’t roll back. Winch boat up to bow stop, and the boat will drop slowly as it gets closer to the stop, and can easily be hitched to the truck again. I’ve done it dozens of times over the years working for a marina. It’s the same technique used to get a boat laying on the ground on a trailer again. Keep in mind, this video below shows a bunk trailer, but the video we’re talking about had a roller trailer, and that’s 10X easier than a bunk trailer. kzbin.info/www/bejne/hpe4dHSYbN6qq7Msi=HCqaKiFaq5aUhbdH

[@tracyosborne646]

@@peglegjim57 i’ve done that too, and it works very well

[@rhino1103751]

Your videos made me look like a Pro loading my 19' Sea Sprite Mercruiser 165 yesterday. I always struggled a bit loading bc I was... you guessed it... TOO DEEP... 😆 Ty sir

[@TheBigDanShow]

Great to hear!

[@chrism2042]

I launched one morning, while my engine was warming up, I watched a guy back a brand new (first launch) 24' center console deep-V down the ramp and had already removed the strap and chain. It was a bunk trailer, but he tapped the brakes and off it came with the back of the boat about 8' from the water when it stopped sliding. He asked me to hook ropes to it and try to drag it down the ramp. I didn't want to do it and also told him my boat wouldn't pull that boat. At that time, I had a 21' Carolina skiff with Suzuki 115. He said, he just picked the boat up the day before and it was his first time launching a boat, he was alone. It was at a lake so no tide to come in. He asked me what I would do, I would call a tow service with a truck that has a boom lift to see if they could help. He didn't even try to call. He ran the strap out, hooked it to the boat, got in his truck and started backing until the bow pushed up on the trailer, then he pushed that boat down the ramp until he got the trailer in the water, then winched it up on the trailer. It was a sickening sight to see that hull after being pushed down that concrete ramp with groove cuts.

[@TheBigDanShow]

@@chrism2042 oh muyyyyyy

[@freighttrainjoe]

What a treat😂

[@wilfor03]

Wow.....first time I've ever seen that operation......Great job...

[@truckdad9999]

I would have used an airbag to slightly lift the stern

[@joeyhardin1288]

Several years ago, a bunch of boaters showed up at a 3 bay ramp. One guy backing down, stopped on the ramp to make sure his plug was in and his boat slid off the trailer. He was wearing some kind of Nylon - plastic bunks and that stuff was so slippery, it just slid off. So a bunch of us got behind and beside the boat (Bass Boat) and just heaved it back on. He strapped it back down and went home. Great video, BTW!

[@TheBigDanShow]

Nice thanks

[@MrShuffnagle]

When Big Dan comes up to you and asks if he can film, you know you did something bad 😂

[@TheBigDanShow]

lol ruh rohhhh

[@alanclarkson1921]

Great video Dan! Clear explanations, and up-close footage. Shit man! You did that better than the 6 o'clock news team!🤣👍

[@TheBigDanShow]

Lmao thanks man 🤣😜

[@georgedelpidio1918]

Saw what happened on another video. They did not attach strap to boat. Drove out to fast and boat slid off of trailer

[@TheBigDanShow]

👌👌

[@josephmellone1269]

This happened to a friend of mine and I was there with my boat and what we did was back the truck up slowly while cranking on the strap pulling the boat without causing any more damage cuz back in the trailer would lift the boat as he's backing in your cranking it worked great without damaging the boat anymore

[@PerryBornIII-q7e]

Big Dan, you should film Port Mansfield Texas one day, hours of video in one visit on a holiday. Hell, I'll pay for it

[@TheBigDanShow]

Haha where exactly is that.

[@yazooyellowcats1403]

I would have put some schedule 40 pvc pipe under it to roll on as it came forward to have help lift it off concrete

[@TheBigDanShow]

Yesssir

[@trumpsturn4733]

ive never seen a boat slide off like that, but a safety chain and properly working and positioned wench is the answer!

[@TheBigDanShow]

Yesssir! 💯

[@thomashardwick673]

Wow that is not as bad as I was expecting to see. Wow big tow bill.

[@TheBigDanShow]

Only thing BAD was the tow bill

[@KAinFL]

I agree with jacks or airbags to lift the back while the trailer is backing up. My two cents worth. We made a dumb move of spraying our bunks with Armor-all - came close to losing the boat first launch. Almost paid stupid tax for the dumb idea.

[@TheBigDanShow]

Oooooof

[@Tom-mu7zy]

I owned an 18 ft Wellcraft for thirty years. I NEVER released the winch or the safety chain till the back of the boat was in the water. My suggestion here, hold the boat with the wrecker and push the trailer back under the boat.

[@TheBigDanShow]

That’s what I was thinking

[@porky7753]

Big Dan, would of been a good opportunity to slang those gel coat kits i talked about before. Although he may need the mesh/ resin kit to build the void back up.

[@TheBigDanShow]

For or 5 layers and he’ll be back under way.

[@NWI_Steel]

I would have tried to jack up the stern of the boat somehow. Maybe a boom lift with long enough arm to sling the rear of the boat from the side cleats or transom eyelets?

[@MichaelFreed-mn4vi]

He could have prevented damage, should have put board's with towels under the tale. Would have only taken a few minutes, and would have prevented the damage.

[@rossevans1774]

Have seen that before. Never rely on the winch strap/ratchet to hold the boat on the trailer. The last thing you do before you reverse the boat off the trailer is detach the safety chain.

[@Hardcopy2362]

Yep. Was watching a guy on another channel with his brand new seadoo explorer and very first trip. Inexperienced driver was backing him in and he had released the safety. Right onto the concrete. Always gotta be thinking three steps ahead for what could happen.

[@rossevans1774]

@@Hardcopy2362 Here is a good example of what happens when your safety chain is unhooked when you are on the ramp. kzbin.info/www/bejne/o5mpmHimiK52aqs

[@zackriden79]

i think with jackstands and a pair of jacks and taking your time you could get back on the trailer with out any external heavy lifting you'd just to get creative maybe some comberlongs too

[@GeorgeT6566]

That is a dang good hull is all I got to say. It held up well for it had to go through.

[@TheBigDanShow]

Got that right. I was suprised

[@kennethnovak9102]

I would have put rolling floor jacks under it before pulling it up with the tow truck, or even a couple of logs would have helped not to drag in on the concrete.

[@TheBigDanShow]

Good idea 👍

[@alanshaw4655]

yep, i woulda used jacks. jack the stern up as high as i could get it, then placed something under the bottom to let the back end slide on. i sure as heck would not have let them drag it up the ramp like they did.

[@JohnnyTalia]

Instead of watching the action at Haulover Inlet, I'm watching the action at Haulonto trailer. My thoughts? One of those wheel dollies they put under car wheels to roll cars around the shop. Jack the hull up and place one right under the drain plug. Or one of those flat furniture dollies would be even better.

[@TheBigDanShow]

Hahaaa

[@Umakemelaff]

Get a couple of big fenders. Deflate. Inflate close to the problem…ride em up.

[@markbrown-rq6is]

Big Dan, 40 yrs ago. I had one roll off the trailer "in" the parking lot at the launch. Bad feeling

[@TheBigDanShow]

Yikessss

[@dougaranda6187]

$1,500? Woof.

[@zackriden79]

looks like that tariler was't for that boat maybe a single axle on a 20 foot boat ?

[@Hardcopy2362]

Late night for you big dan! That bang at 4:27 was hard to hear. They should have at least laid down some planks or something rather than drag that poor thing.

[@trumpsturn4733]

exactly what i was thinking . . . prevent as much damage as possible! buy, they have less interest b/c they get paid to pull it out.

[@edrusin7871]

I was thinking some type of rolling device underneath before they started dragging it.

[@TheBigDanShow]

Not a bad idea.

[@NWI_Steel]

$1500 to winch that back on the trailer?! Sweet jesus, that is highway robbery

[@davids5006]

Yeah that's crazy

[@jameslovitt994]

Go buy a half million dollar piece of equipment, probably $10k a year in insurance, employ someone to operate it. every hour that thing runs is likely 8 to 10 gallons of fuel at $3.50ish a gallon... maintenance... miscellaneous permits & other legalities... Keep in mind, this is a business, how cheaply do you think he should be?

[@NWI_Steel]

@@jameslovitt994 believe me, I get the overhead costs with running a business and maintaining a fleet. But that was the "we have you by the balls" price. A fair price for that recovery would have been 500-800ish IMO

[@jameslovitt994]

@NWI_Steel granted, a smaller truck would've handled the task just fine, they overshot it a bit with what appears to be a 50 ton, once the big guns show up, it gets expensive in a hurry.

[@HigherBracket]

I was going to say that 1500 was fair considering the type of equipment that was used and that I’m assuming this was pretty late on a weekend. However after the entire video, I would have been pissed to pay 1500 and they still drug the hull on the concrete. They could have very easily picked it straight up and sat it on the trailer with no further damage. I would have not taken any issue with the 1500 if the recovery had went different.

[@robertrabhudsonhornet5869]

I would put Jack's on both sides of the hall then put automotive dolly in the middle of the hall so that way the boat is not on the cement then have the tow truck run the soft lines to the back of the boat to the eye hooks

[@TheBigDanShow]

👌👌

[@tracyosborne646]

I’ve had this happen a couple of times he put the truck in neutral and start hand cranking it, and it will force the trailer back under the boat without the boat moving till the boat gets to a certain point that it just teed right onto the trailer and you back it back down in the water and you went your back up Actually a boat fell in the middle of the highway. We back the trailer back up under the boat hooked up the winch put the truck in neutral and we’re cranking it. It was just pulling the truck and trailer right underneath the boat. The boat never slid down the highway or nothing.

[@TheBigDanShow]

There ya go! That sounds good

[@josephwhitehead1692]

I wonder if they could've ran the winch strap under a cross member and back up to the bow eye to pull it down so it would lift the stern until the tow truck could pull it back up.

[@TheBigDanShow]

Good idea.

[@matthewbird8049]

I would ask the water-master to raise the water level

[@TheBigDanShow]

Yessss 🤣

[@oldiron4135]

I is not yo savvy with boats. But i have to ask that if your gonna pay for a recovery truck with a stick, why not strap the boat and lift it? I also need to ask why didnt they put something under the back of boat to keep concrete from diggin into it? At this point he should just rammed it back into the water and reloaded it.

[@TheBigDanShow]

Right good questions

[@NWI_Steel]

Wow the boat actually fared pretty well. Nowhere near the damage i expected

[@TheBigDanShow]

Rightttt

[@leem6011]

What is damaged is where the tow guys drug it on the ramp! Jack up the transom and put some lumber under it for crying out loud!

[@TheBigDanShow]

Yupp

[@shugman3090]

4 X 8 piece of plywood!

[@TairnKA]

Before they start pulling, just the idea of what's going to happen to the boat's keel is cringe worthy. It's a shame the tow truck doesn't have a jack or two and a set of dollies to support the end? Those snapper weren't cheep. ;-D

[@TheBigDanShow]

$225.00lb

[@joeherndon5815]

If that were my boat as the tow truck applied pressure I would of just backed trailer back under the boat as there was plenty of ramp that way the boat wouldn't of skidded along the water grooves and tore it up oh well probably still had to visit the glass man😂

[@1clockmaker1999]

Looks to me like the trailer is too short for the boat…

[@johngiel9471]

Was expecting roller trailer. And you’re right not a ton of damage Lucky coulda been way worse

[@TheBigDanShow]

Yeppp

[@RicoSuave007-z5i]

It'll buff out

[@trumpsturn4733]

not duct tape?

[@jameslovitt994]

Gorilla tape, duct tape is for peasants in John Boats

[@TheBigDanShow]

🤣🤣

[@phillipvernon1185]

I would have trim the motor.

[@Sinikal]

On July 3rd I was backing the boat into the lake and heard my fiance yell WTH and felt the boat pull. I got out and the safety chain was holding it on and the release switch on the winch had snapped which I noticed when we were putting it on when getting off the lake. Then when the boat was ⅔ of the way on the trailer the boat and trailer almost went in the water because I trusted my dad that he lowered and locked the trailer on the hitch. Luckily those safety chains were attached. I wound the boat on the trailer while she dug for a bungie strap in the truck and got the winch part taken care of, then put the wheel down on the trailer and slowly pulled it up out of the water and put it on the hitch correctly. To top it off I was coming in perfectly right on the side of the dock slowly so my fiance was overconfident and put her foot up. As I saw and yelled don't put your foot on the dock it was separating and her legs were spreading. She pushed the boat toward the dock with her leg and fell backwards into the boat. It would have been the perfect outing for your show. REMEMBER SAFETY CHAINS, THEY WORK!

[@TheBigDanShow]

Wow’ thanks for sharing

[@tundrabasser]

Id bring an automotive caster and an automotive jack or two, strap it, lift it and slowly pull it onto the trailer...

[@swift1876]

The tow company should have put skates under the boat to prevent any body damage when they were winching the boat up

[@TheBigDanShow]

👌👌

[@tubnewer]

I would think a tow truck with a boom in the ramp next to them. Reach over and lift by the transom ty down and lift the back of the boat and back the trailer under it. My $.02.

[@TheBigDanShow]

Right

[@dirtroadsailing6418]

I would have put the truck in reverse and winched the trailer up under the boat.

[@TheBigDanShow]

Yesss

[@DonnaKeffer]

For what happened, if all it is is cosmetic damage, I'd say that's awesome.

[@TheBigDanShow]

No doubt!

[@ronmccarroll9588]

Put floor jack under the back of the boat and and back boat and trailer back in to water sure would not cost $1500 and I speak from experience

[@TheBigDanShow]

👌👌👌👌

[@FishingWithDummies78]

sad but it happens

[@TheBigDanShow]

Part of it

[@OttoTheWeim]

Come on now Dan. You should know better than to be standing in the death zone of that tow cable while it is under load

[@TheBigDanShow]

I know better. Taking my chances 🤣 10,000 cable 4,000lb boat

[@OttoTheWeim]

@@TheBigDanShow old comment but just popped back up in my notifications. Even though it was doubled up you have to consider 4K is the weight not the force being applied. Friction on the ramp adds a lot. Isn’t just gravity force for the weight. How about the strap condition and other rigging and I never trust the upkeep of anyone else’s gear that I don’t have control over. I know you were fine but that’s one thing I never mess with due to the multiple areas of potential failure. Who knows when that cable was replaced. Seen too many people get hurt. I’m more surprised the tow driver didn’t clear y’all out for liability. We ALL do dumb stuff, it was just the main thing I could think of watching the video.

[@indianbill3123]

OMG…that tow truck driver had NO business accepting that job because OBVIOUSLY he had no idea what he was doing…or he’s just a moron. Multiple comments here show excellent ideas that would have resulted in NO additional damage while getting the boat back on the trailer.

[@TheBigDanShow]

He put those rubber plates down to act as a keel guard but didn’t have enough.

[@jklivin2007]

ummm…….if Imwas concerned about the boat & not wanting to damage it anymore, I believe I’d call a Crane Rental Company. it’d cost a 3-4 hour minimum, but the boat would be picked straight up & straight back down onto the trailer. 😉

[@Dogandioutdoors]

I mean the boat was already on the ground the truck and trailer should of been pulled out of the way and the big tow truck back up to boat and lift with straps back into water

[@TheBigDanShow]

Just the back was on the concrete. I’m thinking they lift it like that to prevent further damage

[@Hardcopy2362]

@@TheBigDanShow My first thought was to bring in a proper boom and lift her up. Good luck putting that bill through insurance and your renewal rates.

[@dougeaves472]

Air bags

[@freighttrainjoe]

Just don't fix a boat with car Bondo

[@davids5006]

For $1500 I would have expected a reach around

[@TheBigDanShow]

Ain’t no doubt

[@joe-lw6tk]

All you need is a come along and some fucking elbow grease, did it with pickup truck over a bank once!!!

[@TheBigDanShow]

Lol

[@kelseywedge7167]

Very expensive mistake

[@mikewayer5828]

Diy

[@TheBigDanShow]

KZbin it lol

[@blackhawku]

Got your KZbin off Yawt yawt

[@TheBigDanShow]

@@blackhawku welcome to the Family!

[@56igadget]

Terrible terrible terrible tow truck operator

[@TheBigDanShow]

What did he do wrong.?