Front not lowering FIX for 97-01 ES300/Camrys Maxpeedingrods

Just a quick half assed video of what I did to fix my lowering issue on my ES300
Link to swift springs: frsport.com/sw...

[@ManuelMartinez-vj1gn]

Thank you much for the info. Been looking everywhere on how to lower mine more in the front. I actually removed a ring but it didn't change much but a cm

[@ricerintegra2660]

I’m glad I could help 🤙

[@my771]

The maxspeed company suppose switch shorter spring make the Es lower front more

[@andygonzalez3786]

Gained a sub, imma need some more ES videos, it’s hard to find any about aftermarket installation, especially on the Maxpeedingrods install

[@danielbautista0000]

This great advice if you have preexisting coil overs, if you price everything new, $300 plus each coil replacement, you’re already in $500 plus territory. Might as well go with Godspeed or Truhart at this point. Just my opinio.

[@ricerintegra2660]

If I was to go back in time, I definitely would've gotten better quality coilovers for sure

[@jabezlim2439]

Fcking finally thank you I’m gonna try this out tomorrow by just cutting them cause I have been riding in a squatted truck fitment and I’m just gonna save up for some swift coils and swap them out

[@my771]

About time.. yes I knew it.. The coil spring on maxspeed are tall and I contact swift if they can make shorter spring and higher spring rate.. They don’t help me.. I keep research and finally this is it.. gonna order Coil

[@my771]

Finally done.. thanks for info.. my car look lot better then before

[@DnaNatureAquatics]

did you have to buy two springs separate or did it come as a pair

[@my771]

@@DnaNatureAquatics it come with ea spring.. I had to buy two springs

[@eatngoodtv]

what size rims/ offset??? and tires? Are you using spacers behind the rims?

[@johngarcia6434]

Can you fit 65mm springs on this coilovers

[@heyhihello8310]

Did you have to get different size sway bar links

[@fivestarquisethewaveman1662]

thank you!!!!!!

[@johngarcia6434]

Ei man nice ride i see you used 6 inch 70 mm Id springs I wanna do th same to my camry I have someone selling me a pair of 6 inch 65mm id but not sure if they'll fit my coilovers Can anybody help me thanks in advance

[@johngarcia6434]

Did you change the sway bar links too

[@ricerintegra2660]

I ran without them, I think there are adjustable sway bar links online but not sure where

[@rexultimus1422]

where did you get the clear corner markers

[@ricerintegra2660]

www.ebay.com/itm/DEPO-CLEAR-Front-Corner-Lights-Lamps-Set-FIT-FOR-97-98-99-Lexus-ES300-US-Spec-/401634686125?_trksid=p2349624.m46890.l49286

[@greecedaugherty5087]

What’s the inner diameter of the swift springs

[@DnaNatureAquatics]

hey what size rims and tires do you have on there? any fitment issues?

[@colinbowers8813]

When you order the new swift springs, did they come as a pair or did you have to order two individual items to get the two fronts. They're back ordered on the website right now.

[@DnaNatureAquatics]

did you ever get the answer to this?

[@colinbowers8813]

@@DnaNatureAquatics I was told price is for EACH spring. I ended up selling my Camry 😕

[@henrythegecko780]

Where did you get side skirts from

[@darvincaballeros7980]

How much is your car?

[@1_slow4.66]

Is it possible to go even lower

[@ricerintegra2660]

Yea, a guy that I know is slamming his out to the max, cut out the floor & raised it, it's super low. His Instagram is @camberedlex

[@ricerintegra2660]

I cant remember what coils he's using, I think BC extreme lows

[@qsgarage4052]

What are the wheel spec

[@ricerintegra2660]

18x9.5 +35, I got 3/4" rear spacers in the back to prevent from the wheels rubbing on the struts

[@rtroeun]

Ricer Integra so no spacers in the front ? 19” looks good on it

[@ricerintegra2660]

@@rtroeun with spacers in the front they would've stuck out too far, but with the rear, since I assume its suppose to be a staggered type of setup with these cars, the rears sat too far in, so I ran spacers in the rear to combat them sitting too far in and hitting my struts

[@rtroeun]

@@ricerintegra2660 totally understand you now! So did you have to get extended studs for the rears then ? Since you got the 3/4” spacers? Keep up the good content man!!

[@ricerintegra2660]

Luckily the OEM studs were long enough to fit and tighten down for the spacers, I got the ebay ones where you fit it on the OEM lug studs and on the spacer itself it's got studs on it, I'll post a link if i can find it again 🤙

[@danielyvanez2986]

Ay man you got ig?

[@ricerintegra2660]

Yup @ricerintegra