FRUSTRATING Service Of A Zama M1 Carburetor For McCulloch 110!

[@deweylegend6577]

real nice that your hands are in the way all the time!

[@notajp]

I’ve found that E85 gas dissolves varnish very well. I used it to clean out a tank on an old Homelite 360 once.

[@lowellwhite8810]

This is all stuff i need to see and hear. Thank you

[@ericbrobst8160]

Nice work! The haters gonna hate. I though you handled it well. You must have patience working on these McCullochs.

[@rhondafergerson5338]

You have a very nice voice, I could listen to you talk about carbs all day. Thank you

[@QuaabQueb]

Very good detailed video. These mini mac's are probably the worst design I have ever seen. You have to disassemble the entire saw to get the carburetor out! Once you do, now you have this complicated and poorly designed zama to deal with. A huge pain, but an interesting learning experience. A tip regarding getting the new gaskets to seal, soak them in a bit of oil first. They rarely seal right out of the packaging. Generally they swell up only after the fuel mix has made contact with them.

[@nbpt1000]

what kind of oil do you use to soak the gasket? a light motor oil ok?

[@QuaabQueb]

@@nbpt1000 yes any. You can even thin it out with a bit of gas

[@lowellwhite8810]

Thank you for mentioning this, i needed it

[@asaprior4452]

I find when I'm rebuilding a Zama carb it's best to relax turn off the phone lock the door and scream obscenities at it until I have it fixed or have thrown it through a window.

[@justinweaver8787]

Talented fella thanks for the video

[@cphank3722]

The leaking needle may be dry. A little fuel on it may help seal it. Also I may not have been paying attention but did you remove both high and low speed screws and clean passages and ports thoroughly? I didn't see cleaning the low speed screw and passages

[@j.k.mcclead9207]

When I get a carb that crusty and varnished, I put it in the ultrasonic cleaner on its hottest setting for about an hour. While still hot and fresh out of the UC, I hit it with PB Blaster and compressed air. Wear a full face shield because it's going to get messy, but this method hasn’t failed me yet.

[@timberray9572]

I once bought a 575XP husky with a Zama carb, I just could not get it dialed in. I sold the saw with full disclosure to another guy, a few weeks later he called me and told me he couldn't make it run right. I stick to Walbro's or Tillotson now, no issues.

[@garazschannel4411]

I converted the carburetor. I bypassed the non-return valve at the main nozzle. That's right, the Walbrocarburator.

[@davewright6154]

Thank you.

[@BrucesShop]

Yes. It only happens when the camera is going. Still great work. Bruce

[@nbpt1000]

very helpful. thanks. I find carb cleaner is not the best on cleaning crud especially etholol damage. Soak it in penetrating fluid for a few hours or even days can loosen up the crap. Then clean it up with carb or brake cleaner.

[@nbpt1000]

Leon: Can you just shake the carb and listen to hear if the check valve moves and makes a slight noise? I know you can do that on some 4 cycle carbs that have an internal check valve. Thanks!!

[@cphank3722]

I've had good luck using acetone to dissolve thick varnish. Acetone will dissolve many plastics too so remove plastics from anything to be exposed to acetone or test the plastic first.

[@b-ryanistryin]

Do you ever use Ultra Sonic cleaners?

[@juanvillarrealsr124]

Which way should that valve block

[@cphank3722]

A sliver of electrical tape with the screw through it and taped to the end of the screwdriver acts almost like a magnetic screwdriver on your brass screws.

[@imaoregonbum6683]

It is not my Glasses that's out of frame? Fossil Puel. That's what they tell vocalists between the diaphragm

[@stevequate1797]

I wished I could just ship you my carb. I don’t know how to PM or send personal messages to the person making the video. Not smart enough to know how, damnit pisses me off not knowing how to do something. Wished the camera was closer to the carb so I would know exactly how each thing suppose to be and go back on. I just wished I knew if everything was put back correctly on my carb thanks this vid helps I’m just not exactly sure ya know I like to know exactly

[@jimmyhuffman6802]

Taking way to much time.

[@fearghalmorrissey2601]

First lol