No video

FSi6X Failsafe Setup Tutorial - How to Use FlySky Transmitter Failsafe (fs-i6x, fs-i6)

  Рет қаралды 40,350

RCwithAdam

RCwithAdam

Күн бұрын

Пікірлер: 103
@hidesudou
@hidesudou 5 ай бұрын
Thanks Adam! 2:42
@tonyholmes7992
@tonyholmes7992 3 жыл бұрын
'Another cracking explanation. You achieve what a manual fails to do. Much appreciated.
@George25
@George25 10 күн бұрын
I smile so much Adam ,since I found your channel , You have everything I need to learn and start setting up my first transmitter and receiver ( Flysky FS I6 ) cheers mate for all your help 👍🦘🦘👏👏👍🦘🦘
@RCwithAdam1
@RCwithAdam1 10 күн бұрын
Thank you! That's fantastic to hear! 👍 welcome to the hobby!
@michaelbajo9966
@michaelbajo9966 4 жыл бұрын
You are they only one that talked about adding elevator when in failsafe. Nice one! 🖒
@brandonpritchard5
@brandonpritchard5 3 жыл бұрын
Thx Adam. You rock! You saved my bacon...again. You do a really good job. Some people bore the crap out of me, others are so spastic, I just can't stand to hear their voice! You strike a good balance between being entertaining and, presenting the materidl in a easy to follow, easy to understand way.👍🙏
@RCwithAdam1
@RCwithAdam1 3 жыл бұрын
Well thank you very much! I'm glad to hear my videos are helping you! 😃🙌
@JonFloFPV
@JonFloFPV 3 жыл бұрын
After finally getting an old hand-me-down Diatone Tyrant running, I watched your videos on setting up failsafes and setting the arming switch on my Flysky i6x... and now I'm good to go :) Thank you so much for your info sharing! It helps a lot of us get off the ground - literally.
@coltaarav5416
@coltaarav5416 3 жыл бұрын
You prolly dont give a damn but does anybody know a trick to get back into an instagram account?? I somehow forgot my account password. I would appreciate any help you can give me.
@elliotjerome6294
@elliotjerome6294 3 жыл бұрын
@Colt Aarav Instablaster =)
@josephsopala7642
@josephsopala7642 4 жыл бұрын
Sanks so much to you...for this detailed and to the point video. I was out flying a minute ago and wondered if I had put the failsafe on my new plane settings and of course I didn't but I tested it anyway by turning off my FS Tx . Needless to say it kept going. For some reason, even in panic mode, I was able to reconnect before it got away. After that I couldn't remember for the life of me how to set up failsafe so your video was very helpful. Back to terrorizing the neighborhood.
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Happy to help and good save!
@richarddorsch7275
@richarddorsch7275 Жыл бұрын
You have the best info lessons on flysky.
@RCwithAdam1
@RCwithAdam1 Жыл бұрын
Thanks!
@petrblaha6618
@petrblaha6618 3 ай бұрын
TIP: try to set the elevator and rudder both to 100% and motor to -100%. The plane would go into spiraling down but in the end it slows down and lands like a miracle (at least for gliders). That's what an old PRO pilot taught me years ago...
@josefmechanic
@josefmechanic 3 жыл бұрын
This is awesome I never knew what this did and it using this remote and reciver for a mt2 hpi rc and it works incredibly ❤️
@RCwithAdam1
@RCwithAdam1 3 жыл бұрын
Great to hear! 👍
@cadser0engco
@cadser0engco 4 ай бұрын
Easy explanation Thank you.
@frangie9858
@frangie9858 2 жыл бұрын
thanks for this amazing tutorial im going to remember this so if have this transmitter i can use that failsafe thing thankyou
@LucianBlox
@LucianBlox Жыл бұрын
you could also make the rutter turn to the left or right, while the elevator is slightly up so the plane wouldn't just keep going; it would go in circles
@RCwithAdam1
@RCwithAdam1 Жыл бұрын
That could be a good idea.
@LucianBlox
@LucianBlox Жыл бұрын
@@RCwithAdam1 but also u can buy zohd gps and use return to home. zohd RTH can be activated by a switch so ur failsafe could put the switch up to start RTH
@lucywucyyy
@lucywucyyy 3 жыл бұрын
id add a tiny bit of rudder so the plane will glide in circles, hopfully tbhat would stop it from gliding further away
@RCwithAdam1
@RCwithAdam1 3 жыл бұрын
Good idea!
@longjammeriii3323
@longjammeriii3323 4 жыл бұрын
That's some really interesting and great advice, thanks for sharing, regards, Alan, uk
@cooperthompson4850
@cooperthompson4850 2 жыл бұрын
Flysky fam: "Our transmitters cheap and our wallets happy."
@doubletapgaming1189
@doubletapgaming1189 4 жыл бұрын
I'm part of the flysky fam. Thanks for all the tips.
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Highfive! 🙏 👌
@amoeslund
@amoeslund 4 жыл бұрын
I only think this applies to drones. Some flysky receivers have problems to detect failsafe. If it doesn't work on your receiver this did the trick for my fs-ia6b. FIX: Go to your controller menu - Function setup - End Points and set you low value for channel 3 to 120%. (throttle chanel) Go to System Setup - RX setup - Failsafe - and setup your failsafe for channel 3, which now can set to -120% (950) Go back and set your end point for channel 3 back to 100% (else you will failsafe when you throttle down ;-) ) Go to failsafe tap in Betaflight and set Minimum length in Valid Pulse Range Settings to 970 (or somewhere else in between 950-990) And then it should work... test it before you fly!
@teamsmokeyrobotics
@teamsmokeyrobotics Жыл бұрын
Thank you! Good video.
@timewaster1959
@timewaster1959 Жыл бұрын
As usual brilliant!!!😊
@FRANLAC
@FRANLAC 2 жыл бұрын
perfect very good explain Thnaks .
@tallguyfpv
@tallguyfpv 4 жыл бұрын
Now here is something I can use
@SaereeNon
@SaereeNon 11 ай бұрын
So good!
@iassacspurlin1368
@iassacspurlin1368 4 жыл бұрын
Great video i did not understsnd how it works or what failsafe is, you da man!
@SubhashMishra
@SubhashMishra 3 жыл бұрын
Nice information
@stefedwards2934
@stefedwards2934 4 жыл бұрын
Thanks Adam, you are a star👍🇬🇧
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
lol thanks! 🤩
@marcjourdain299
@marcjourdain299 3 жыл бұрын
très bon conseils. merci beaucoup
@elbecer
@elbecer 6 ай бұрын
thank you!
@anuragsingh9557
@anuragsingh9557 4 жыл бұрын
Thanks Adam just what i needed
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Awesome! 👍
@MURDOG2002
@MURDOG2002 3 ай бұрын
So this radio & receiver has a built-in failsafe? No need to buy one separately?
@KingBeetle1966
@KingBeetle1966 4 жыл бұрын
So if I had an AUX channel set to ReturnToLaunch (GPS Rescue in BetaFlight) when in the "ON" position, I can program the transmitter on my hexacopter to automatically engage and come back if it loses the transmitter signal! Nifty!
@huntingwheels7374
@huntingwheels7374 3 жыл бұрын
hi RCwithAdam i have one problem with my set up i have the same radio but my motor only work when i have half of throttle and some times spin on booth sizes.. can you help me?
@dhavesy5730
@dhavesy5730 4 жыл бұрын
Hi Adam,please teach us a video on how to setup rssi on fs-i6s. Thanks
@praveen6740
@praveen6740 4 жыл бұрын
Awesome video 👍👍
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Thank you 👍
@plewisto
@plewisto 2 жыл бұрын
My transmitter does a series of 3 beeps and a pause while retaining full control. Do you know what this means?
@vanshy8540
@vanshy8540 2 жыл бұрын
Thanks a lot.
@RCwithAdam1
@RCwithAdam1 2 жыл бұрын
Glad to help!
@richarddorsch7275
@richarddorsch7275 11 ай бұрын
Adam, it just won't work with the micro receiver fs2a c channel. I've tried and tried but still won't work. Do you have any ideas? Thanks
@ezonigs3107
@ezonigs3107 3 жыл бұрын
Thanks a lot
@woutersmith7616
@woutersmith7616 3 ай бұрын
Hi Adam. I have a F450 Diy quad. Want to use the Naza mlite with the FS-i6X. Cannot get the Sw-C allocated wity pos1=Manual,pos2=Altti and pos3=Gps. My pos2 ends up in FAILSAFE iso. Altti🤔😪. ENDPOINTS works on pos1 and pos3,but pos2 cant set? Wouter
@dmctec5943
@dmctec5943 3 жыл бұрын
Thxs.. But It's better to buy a controller with GPS and configure GPS Rescue Mode in Betaflight, INAV, other softwares, and your model will return to its takeoff point, you can recover it and save it!
@kennethholland4627
@kennethholland4627 11 ай бұрын
Okay. I have a question. I have a tracked crawler set up with a real time camera to do crawl space inspections with.. My problem is that when the battery on the vehicle itself gets low, it surges backwards. This can be a real problem when it's underneath a house because when it does this, I have no control over it. It has backed itself into tight spots where it knocks the camrea around and once even pulled the entennas off. Can I set a failsafe on my FlySky i6 to avoid this problem? If I have to crawl under a house to retrieve it is one thig, but to have it crawling backwards out of control and possibly damaging the vehicle is a real problem. Can you help me?
@jeremiahthomas8568
@jeremiahthomas8568 3 жыл бұрын
my failsafe only stops at -87% when the throttle is all the way down.
@lucywucyyy
@lucywucyyy 3 жыл бұрын
if you had a gyro or an autopilot could you connect those to the failsafe to make the plane land itself or something?
@leskauhane560
@leskauhane560 3 жыл бұрын
How to set up a safe mode or panic mode for beginers
@ladislavbattyanyi1318
@ladislavbattyanyi1318 7 ай бұрын
pls help me how to set up for radjet 800
@desthyyap2160
@desthyyap2160 4 жыл бұрын
hi adam, desthy here from the Philippines. nice and very informative videos you have. i have a question though and hope you can help me with it. in my old fm pcm futaba radios, we usually do range checks by walking about 50m from the plane with the transmitter antenna down to see if it works fine...and in some 2.4ghz radios like spectrum, they have a range check button...how do you range check an fs-i6x? thanks!
@NewYorkeez
@NewYorkeez 4 жыл бұрын
Hey Adam, how to set up pitch roll and yaw when you build your own flight controller? Same rc controller
@itsme-tm4vd
@itsme-tm4vd 3 жыл бұрын
graet .thank for the video
@wweber1700
@wweber1700 4 жыл бұрын
tnks man, you save me
@zizoeldjazairi7922
@zizoeldjazairi7922 10 ай бұрын
what is its max range
@robertbrander2074
@robertbrander2074 4 жыл бұрын
Good Lesson Son ! I will be using that a lot ! ....... How good is the i6 to i6x software update ? Have you heard of any problems with it ? Is it buggy ? I want to try it but am nervous ....... Cheers !
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hi! Seems to be working fine so far!
@royd7984
@royd7984 3 жыл бұрын
What is the best ESC to get for a 4 channel trainer and the FS16X? I'm new to the hobby. Thanks very much.
@RCwithAdam1
@RCwithAdam1 3 жыл бұрын
Hi! Welcome to the hobby. I've enjoyed Emax 12amp, 20amp, and 30amp ESCs. Make sure the connector matches your battery's connector.
@thatguyblue4811
@thatguyblue4811 2 жыл бұрын
How would you set this if you were trying to set up RTH?
@RCwithAdam1
@RCwithAdam1 2 жыл бұрын
Hi! That depends on a LOT of factors, like the aircraft, gps unit, flight controller, firmware, etc.
@richarddorsch7275
@richarddorsch7275 11 ай бұрын
Typo....It's a 4 channel micro fs2a
@NavneetSharmaa
@NavneetSharmaa 4 жыл бұрын
Thanks bro...
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
My pleasure
@bearfpv9377
@bearfpv9377 3 жыл бұрын
It works with any receiver from flysky?
@RCwithAdam1
@RCwithAdam1 3 жыл бұрын
Sorta. It works with AFHDS (the older ones) and AFHDS 2A (newer, common ones), But will not work with FlySky's latest AFHDS3 receivers.
@kaseym6992
@kaseym6992 4 жыл бұрын
Have you figured out a timer for the i6X? I have seen where there is a software mod for the i6 but don't think it works with the i6X. Or any suggestions for a timer?
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hi! I have not. And I still haven't found it on the i6 10ch mod.
@ricardoprieto7124
@ricardoprieto7124 3 жыл бұрын
Hi, I have a fs i6 and I want to put a 3ch rx, this receptor is a viable with this transmitter the binding is OK, he works right in all channels, but don't works the failsafe, I do the set up for this 3 ch receptor and when I cut the TX the rc model do not cut...... You know some solution, thank you in advance.....
@RCwithAdam1
@RCwithAdam1 3 жыл бұрын
What model receiver are you using?
@ricardoprieto7124
@ricardoprieto7124 3 жыл бұрын
@@RCwithAdam1 a fly sky 3channels receptor..... Is the recommended for flysky for this transmitter....is ahfs 2a too, and is the same of gt3 flysky transmitter, if you need.... Give you the model correct..... Thank you
@bluepple6478
@bluepple6478 2 жыл бұрын
what idf the plane battery died will it still be able to do the failsafe?
@RCwithAdam1
@RCwithAdam1 2 жыл бұрын
Good question! No. If the flight battery drains completely or becomes disconnected, the failsafe will not work (although I've never actually tested this). But it doesn't take much voltage to operate the servos, so at super low voltage the motor might not work but servos will.
@bluepple6478
@bluepple6478 2 жыл бұрын
@@RCwithAdam1 so i will need a reserve battery to activate a emergency parachute or somewhat
@bluepple6478
@bluepple6478 2 жыл бұрын
@@RCwithAdam1 and i could use a very large capacitator to activate the failsafe
@Shinobi117
@Shinobi117 4 жыл бұрын
Do I have to set up fail safe via the transmitter if I have GPS on my quad and airplane?
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
I haven't played with GPS yet, but I don't think so.
@Shinobi117
@Shinobi117 4 жыл бұрын
@@RCwithAdam1 yes I found out with the bgl autopilot you have to set a switch for RTH and set throttle at a cruising (altitude maintaining) speed. Adam you've helped me before. Thanks for your easy to understand videos plus you make it fun to watch. Don't you dare stop!!!
@dharmeshpanchal4324
@dharmeshpanchal4324 Жыл бұрын
How much rs
@dbproductions6656
@dbproductions6656 4 жыл бұрын
what are your thoughts on the x6b reciver?? great video by the way
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hi! The X6B is a fine receiver, I've used it a lot successfully, but now there are better options out there. Specifically, I'm using the Fli14+ and CrossoverRX receivers instead. But if you don't mind the extra size/weight, they work just fine!
@CliffHarveyRCPlanes
@CliffHarveyRCPlanes 4 жыл бұрын
Good info Adam but when I select rx setup my only option is 'AFHDS' ! Any ideas?
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hi, Cliff! Do you have the i6X or just the i6?
@CliffHarveyRCPlanes
@CliffHarveyRCPlanes 4 жыл бұрын
@@RCwithAdam1 It's the i6, I'm guessing you're going to say it's only the 'X' which has these options?
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hey! I just checked on my i6. I think yours was on AFHDS mode. In the RX setup menu, Press OK on the AFHDS, then AFHDS 2A should show up. Then select ON. Now the RX SETUP menu should have all many other options, including failsafe. Let me know if this works!
@CliffHarveyRCPlanes
@CliffHarveyRCPlanes 4 жыл бұрын
@@RCwithAdam1 Your right, the AFHDS 2A shows up, I then select ON, and the screen now says AFHDS 2A with the word OFF below it, I then select ON and I'm returned to the screen that says AFHDS, weird!
@mohanedhassan4743
@mohanedhassan4743 4 жыл бұрын
Is it work with quadcopter
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hi! Absolutely!
@rogermaz9025
@rogermaz9025 4 жыл бұрын
Adam, I noticed when you moved the throttle a bit the engine turned on in my case I have a dead zone I have to move the stick almost half way up till engine starts to run.Is there a way to fix that.
@RCwithAdam1
@RCwithAdam1 4 жыл бұрын
Hi! I would try calibrating the esc for your throttle. Each esc manufacturer should have info on how to do that.
@desthyyap2160
@desthyyap2160 4 жыл бұрын
hi Roger, try calibrating the esc again with your tx. remove the propeller first then move your throttle to wot position. turn on tx, then attach power to rx. usually you will here 2beeps then move throttle to full down. you will hear the esc arm and that's it, esc calibrated. hope this helps.
@dzulw
@dzulw 2 жыл бұрын
it didn't work for me. only when I set the ARM button on failsafe. channel 6 for me
@woutersmith7616
@woutersmith7616 3 ай бұрын
Hi Adam. I have a F450 Diy quad. Want to use the Naza mlite with the FS-i6X. Cannot get the Sw-C allocated wity pos1=Manual,pos2=Altti and pos3=Gps. My pos2 ends up in FAILSAFE iso. Altti🤔😪. ENDPOINTS works on pos1 and pos3,but pos2 cant set? Wouter
Вы чего бл….🤣🤣🙏🏽🙏🏽🙏🏽
00:18
managed to catch #tiktok
00:16
Анастасия Тарасова
Рет қаралды 41 МЛН
Parenting hacks and gadgets against mosquitoes 🦟👶
00:21
Let's GLOW!
Рет қаралды 13 МЛН
FlySky FS i6 programming
12:18
Andrew Newton
Рет қаралды 238 М.
FlySKY FS- i6 Basic 4ch Setup
6:48
Andrew Newton
Рет қаралды 136 М.
FlySky FS-i6X  How to Setup TOP 5 FUNCTIONS for BEGINNER PILOTS
10:12
Is FlySky Worth It??? (Yes) - FS-i6X A Best Budget Radio
10:20
RCwithAdam
Рет қаралды 58 М.