Fuel Rail Pressure Test with VCDS by Ross-Tech

  Рет қаралды 268,006

RossTechVCDS

RossTechVCDS

Күн бұрын

Пікірлер: 59
@longgoneg60
@longgoneg60 5 жыл бұрын
Great walk through, used on 06 BPY. I have a cyl 2&4 misfire. Plugs and coilpacks just replaced. I ran this test and was somewhat pleased to find I don’t have any leaking injectors. Now I can trouble shoot wiring. Thanks guys
@hendersonjp
@hendersonjp 7 жыл бұрын
nice to have you back .ace info thanks
@kritikos986
@kritikos986 4 жыл бұрын
where you find all this code for the group???
@necromastercz
@necromastercz 4 ай бұрын
Hello, I have EA888 engine (1.8 TSi from 2010) and my appearance for group 106 is bit different - I can see here value "Fuel Temperature (calculated)" that shows temperatures about -50°C (yes minus 50). Any idea how is this temperature calculated? I have problems with extreme rough cold starts and this seems to be in relation with my problem. Thanks
@jasonfoster8871
@jasonfoster8871 5 жыл бұрын
What is the most common cause if the vehicle loses pressure after being shut off? Fuel pump check valve?
@RossTechVCDS
@RossTechVCDS 5 жыл бұрын
Leaking fuel injectors. IMHO, if one is bad, replace all of them at the same time. We've seen a lot of people pin down which injector is bad and replace it. Then 2 or 3 months later, another injector starts to fail and bleed out all the time.
@jasonfoster8871
@jasonfoster8871 5 жыл бұрын
Thank you. Ended up changing all 4 Injectors on your recommendation. Fuel trims now at 0.8-1.6 LTFT instead of - 20LTFT
@markmacdonald188
@markmacdonald188 5 жыл бұрын
I done this test.. My rail pressure went up to 70+ Barr I have low rail pressure code. Been using Vfizz controller to access ECU data . Would the 70+ Barr be a false reading or is this working to factory design.
@Exorcism47
@Exorcism47 2 жыл бұрын
@@jasonfoster8871 you had (negative) -20 LTFT and the problem were the injectors?
@repeater95
@repeater95 Жыл бұрын
@@Exorcism47 most likely
@matedu4508
@matedu4508 2 жыл бұрын
Hello. I would like to know if it is possible to check the pressure from the oil pump for the engine, to see if it works within my parameters.Because I sometimes get a low oil pressure message.And I would like to know if with vag com you can check the pressure, and what are the values ​​that should be in an Audi Q5. Thank you
@RossTechVCDS
@RossTechVCDS 2 жыл бұрын
Most engine tend to not report oil pressure via the data port. Join our forum and post an auto-scan from your vehicle there for additional assistance. forums.ross-tech.com/forum.php
@cesarjorgemurillobarientos1813
@cesarjorgemurillobarientos1813 4 жыл бұрын
very good my brother
@clearkill1337
@clearkill1337 3 жыл бұрын
I've noticed my values for group 230 are very low. Specified never exceeds 1.99 and actual is either 0 or .96 while group 140 actually shows proper rail pressure of at least 40bar
@valentindobre9080
@valentindobre9080 3 жыл бұрын
Hy Ross… can u help me … i have golf 6 . 160 cp last 2 weeks i change high pump becouse i see leak petrol in oil and now i see … fuel rail when engine is off 49bar is go down …! High pump is new before that the old pump when i testing pressure is going up to 120 bar … what the problem i have ?
@adrianculda2259
@adrianculda2259 3 жыл бұрын
I've got Sharan 2.0 2011,and have done everything you have said in the video, my fuel high pressure: actual value was 4700hPa at 84⁰ Coolant Temperature, after shut off the engine and start again but not the engine, the Fuel High pressure has decrease at 2200 hPa after 2 minutes, so didn't increased as you said in the video, could I have a problem? Thanks
@Exorcism47
@Exorcism47 2 жыл бұрын
Same here. 2.0 TFSI engine, fuel rail pressure slowly drops instead of going up with the engine warmed up. Checked each spark plug for gasoline smell, none had gasoline smell. Have you fixed the issue?
@TheGorank1982
@TheGorank1982 9 ай бұрын
​@@Exorcism47 same by me 1.4 tsi engine...
@louisstroomer4220
@louisstroomer4220 6 жыл бұрын
Tested my (suspected) Fuel Rail Pressure today the way you showed. My Passat has the 3.6 BLV engine and shows the engine light and idles pretty rough. During the test it shows a pressure of around 128 Bar. It doesn't tell me the specified pressure it should measure do I don't know for sure if it's to high - can you confirm please? After shutting the engine down the pressure drops to around 118 bar right away, then slowly rises up to around 128 again if I wait 10 minutes. Does that indicate a leak? If a fuel injector is bad, or a fuel injector gasket is blown, is there a way to tell? I noticed the lambda for both rails around 20 (and specification is -10 to +10, it says). Can you please advise? Thanks, Louis
@FourRingsAuto
@FourRingsAuto 5 жыл бұрын
Seen 3.6fsi with broken timing chain guides and fuel pump jumped timing. your high pressure fuel system is reverting to default running mode and operating at higher usual pressure due to this. Just a suggestion but I'm sure you've had it fixed by now.
@Theoloop
@Theoloop 7 жыл бұрын
So mine stays steady for 5+ minutes and never rises. Are there other steps to diagnose further? 2.0t fsi, rough idle every once in awhile. New plugs coils and cleaned valves.
@RossTechVCDS
@RossTechVCDS 7 жыл бұрын
Our registered customers can get free vehicle support on our web forum: forums.ross-tech.com/forum.php
@klisurski
@klisurski 6 жыл бұрын
Theo Lupu I have 1.8tfsi and mine does even slightly drop after a minute from 39 to 36. I don't have any error codes. My engine is a bit rough in idle and I am suspicious. Did you find the problem?
@EZ-D-FIANT
@EZ-D-FIANT 9 ай бұрын
Are you guys the people who sell vcds then. I just looked its about £650 uk which is a lot of money for me, I already have 2 otber diagnostic systems and neither recognises my 2013 2.0tdi golf, so if vcds comcomes with help Id alpre appreciate​@RossTechVCDS
@djamel_bijoux
@djamel_bijoux 3 жыл бұрын
On my 2011mk6 GTI I have a p2293 when the car gets to operating temperature it stall and won't start until it's cooled down any suggestions please ?
@popmayhem7361
@popmayhem7361 3 жыл бұрын
Hi Ross-tech..tried to do this on a mk5 golf/rabbit and all the suggesed group numbers (106, 140, 141, 230) are blank (no readings) even on latest vcds. using micro-can cable. what would be the reason for this?
@y.b.zgaim3766
@y.b.zgaim3766 2 жыл бұрын
Allo there ,did you find the group numbers i have the same problem. ??
@ww5220
@ww5220 3 ай бұрын
How long such 63bar shall last? Engine is cooling down, so it shall keep 40bar or can go lowe and how fast?
@10Eight
@10Eight 3 ай бұрын
If the fuel rail is increasing in pressure the injectors are holding pressure. The question you should be asking is "How does a fuel rail work" The fuel rail builds and holds pressure for ever the whole fuel system is under constant pressure no vac. So there should always be some pressure in the rail. Once the car warms up turn off the car and the fuel pressure should rise due to "heat soak" gas expands under heat once gas cools down it shrinks.
@ww5220
@ww5220 3 ай бұрын
@@10Eight Fuel pump in tank holds 7bar. How much shall keep high pressure pump and if this could go back to tank, as there is ni other way to decrease pressure as internal leak of HP pump or injectors. It can go only as backpressure to the tank.. But it shall?
@GustavoFreeng
@GustavoFreeng 4 жыл бұрын
What about Diesel? Is it the same??
@jvecu94
@jvecu94 5 жыл бұрын
On Golf 7 2013 ,2.0 TDI what is the right value of fuel pressure? Mine is about 25.000-30.000kpa on 800rpm is that the right value?
@daves2369
@daves2369 2 жыл бұрын
Mine went from 36 to 42 after 4 mins. 2013 V6 Audi S5. Should it be higher? I smell fuel while driving plus fuel in oil.
@senorslowbrz
@senorslowbrz 2 жыл бұрын
do a compression test. sounds like bad rings
@KenyonPayne
@KenyonPayne 4 жыл бұрын
I bought a 2010 Passat CC and has a p0088 with rail pressure being at over 80bar at idle. What can I test to determine what's the problem?
@IamJimhunder
@IamJimhunder 3 жыл бұрын
fuel filter could be 1 of the causes, it has a built it regulator and that may have failed.
@KenyonPayne
@KenyonPayne 3 жыл бұрын
@@IamJimhunder the timing chain skipped a couple of teeth and fuel pump was overpressuring
@IamJimhunder
@IamJimhunder 3 жыл бұрын
@@KenyonPayne oh dear how did you find that out?
@redadiagnostic4631
@redadiagnostic4631 4 жыл бұрын
How you can know this code like 106... Can you help
@racingjoe1
@racingjoe1 9 ай бұрын
My vcdd by Ross doesn't have "blocks" I'm stuck trying to read pressure in hpa. What the hell is hpa?
@hookpaonline3349
@hookpaonline3349 6 жыл бұрын
Hi , what about Audi A3 8l, 1.6 , 2001. I can’t find it
@TheAbbott1986
@TheAbbott1986 2 жыл бұрын
Can you test fuel pressure if car won't start ?
@RossTechVCDS
@RossTechVCDS 2 жыл бұрын
Sort of... you can see how much pressure is on the rail while cranking the engine over.
@b0000stwagen
@b0000stwagen 2 жыл бұрын
@@RossTechVCDS is there a rule of thumb for fuel rail pressure when cranking? I have a crank, no start condition. Fuel rail pressure is only 5.7 bar when cranking.
@TheSweetVillain
@TheSweetVillain 2 жыл бұрын
@@RossTechVCDS Hello, is there a way to find what is the factory fuel pressure value for the CFHC 2.0 TDI Common Rail Engine ? At idle and with the engine warm or cold, IDE00188 Fuel high pressure : actual value indicates 319700 hPa, while IDE00589 Fuel pressure is fluctuating around 27580 kPa rel
@brkbt93
@brkbt93 2 жыл бұрын
@@b0000stwagen someone said there should be at least 180bars of pressure for the injectors to start firing. Btw did u fix ur problem ? did u start u car ?
@avantsautomotive6022
@avantsautomotive6022 7 жыл бұрын
Good job Jeff It was a hard lesson for me and you to come up with high pressure in the 140 block ???? Your welcome HAHAH Thank you for all your help on my issue with that a-6
@RossTechVCDS
@RossTechVCDS 7 жыл бұрын
Indeed. I had started on this video prior to those calls.... and went back and added the addition info and voice over after all that. Never stop learning because the Germans are always going change something. ST?ID=74546
@Atrociousa3
@Atrociousa3 6 жыл бұрын
Is there a specific pressure it’s suppose to go to and stay at? After shut off my pressure can go up to 100bar
@Wartai
@Wartai 6 жыл бұрын
I would like to know too, what pressures it could attain if left longer, my MK6 GTI has gone up to 190bar? But no high pressure errors..
@repeater95
@repeater95 Жыл бұрын
@@Wartaidid you find it is normal to have 190 bar ?
@AngelFix
@AngelFix 6 жыл бұрын
How to check fuel pressure on audi a6 c6 3.0 tdi common rail pre facelift model?
@stefanlazarevic2159
@stefanlazarevic2159 3 жыл бұрын
i have A5 b8 2.0 tfsi, when i turn engine off my pressure went from 4000 to 1190 kpe after 5, 10 min ? what is the problem ? also have new injectors, coils and spark plugs. also my engine shakes every single day, no matter is it hot or cold. And also i have missfires on cylinder number 2, and few days ago i have check engine light and code is p0303, p0300 why ???
@matedu4508
@matedu4508 2 жыл бұрын
AUDI Q5 2.0TDI 177CV QUATRRO
@emiliofl554
@emiliofl554 4 жыл бұрын
Hola como puedo graduar la egr, el cuerpo de mariposa y el acelerador del golf mk4 16c.c.16v 77kw motor bcb, con vag com. Gracias
@hotelsromania
@hotelsromania 5 жыл бұрын
La mine pe canalul 75 imi arata altceva
Start of Injection
5:18
RossTechVCDS
Рет қаралды 402 М.
How To Data Log your Fuel System With VCDS
15:57
Megalodon on Wheels
Рет қаралды 6 М.
Правильный подход к детям
00:18
Beatrise
Рет қаралды 11 МЛН
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
Understanding Fuel Trim by Ross-Tech
7:06
RossTechVCDS
Рет қаралды 380 М.
2011 tdi no start
20:01
CoolAirVw Rm
Рет қаралды 168 М.
Battery Coding
7:06
RossTechVCDS
Рет қаралды 1 МЛН
VCDS cylinder Compression Test
2:44
golf Wagen
Рет қаралды 110 М.
VCDS Tutorial ~ How to Use VCDS Scan Tool
19:47
HumbleMechanic
Рет қаралды 910 М.
EVERY VW & AUDI OWNER SHOULD HAVE THIS! VCDS Showcase - At The Wheel
13:08
Which VW/Audi Scan Tool Should You Buy? VCDS or OBDeleven
29:20
HumbleMechanic
Рет қаралды 413 М.
VW 1.6TDI Injector Quantity Adaptation IDE06141 CAYC engine
6:52
Engine Management Adventures
Рет қаралды 165 М.
Правильный подход к детям
00:18
Beatrise
Рет қаралды 11 МЛН