Full Ride Video of the Avenger 85 and the MZ65 pipe from Gomax Industries

Hey everyone, I wanted to edit and post this ride video so you could see how hard I ran this pig!! What a fun and beautiful trip. I wanted you to have the opportunity to just kick back and enjoy the whole ride without all the work on the Banshee Queen. Plus the clouds were just great this ride and I had a lot of respectful people on the road that day. Just hit all the marks. I think we will rip the Queen just a few more times before upgrading to the new carb…. But we will see!!

[@ericabrams9415]

This is enough evidence for me to order an avenger kit

[@grendelsgarage9723]

Oh yeah don't ever think about it. They are lit 🔥 ❤❤❤🎉🎉🎉

[@ericabrams9415]

@@grendelsgarage9723 Did you replace your wrist pin needle bearing?

[@ericabrams9415]

@@grendelsgarage9723 also curious, what kind of crank and clutch bearings does this baby come with

[@Littleevil9975]

Great video bro bike sounds great once it warms up quick fun as hell right just a tip bro not good to keep flooring it when it’s cold or 4 stroking will be bad in the long run you should warm it up i warm mine up before every video stuff gets expensive have fun bro ride safe

[@Littleevil9975]

Just finished watching that thing rips bro there pretty fast 💨 nice build

[@grendelsgarage9723]

Hey brother thanks for the tip. Yeah, you right. I should crew a little, warm it up, then send it. Dam straight it's not cheap! It was cheap but not anymore hahah 😆 🎉🎉🎉🎉🎉🎉 ride safe brother!

[@SpAcEcruizer203]

And def let it warm up for like 5.5 mins

[@mikemiller3303]

Thanks for sharing brother you were flying I think 50 if your chock wouldn't have vibrated closed on the blue sky run you hit 47 you were close maybe with a vm18 more air flow and fuel but all an all she sounds awesome brother ride safe

[@grendelsgarage9723]

I'm thinking we have maxed out the stock carb basically what you said hahahah 😆 😜. I'm going to upgrade to a Nibbi 19mm carb with the smolik performance manifold after a few more rides. 😉 thanks Mike!

[@KevinTodd]

At that speed of 48 things happen really fast be careful

[@grendelsgarage9723]

No joke!!!! Ordered a new helmet. I'm Going to get some safety stuff. Also check your bikes before each ride. At these speeds, things shake loose.

[@leonardarola]

Keep going at it. Was good, to the roots. Thanks for the ride.😂

[@grendelsgarage9723]

Thanks brother 🙏. I wasn't going to post this video but I felt the same. Just a good day to ride and want you all to enjoy it to.

[@dustinh4175]

I spent the 30 bucks and bought an arch chain tensioner and its a little more trouble to get it lined up but not having to worry about the 4 bolt tensioner going into the spokes and killing me was well worth the money. Looking down at my tensioner at 30mph is what made me crash my mongoose.

[@grendelsgarage9723]

Whar style did you go with? I have one, but can't get it to aline at all. Anyways ride safe!!! 🎉🎉🎉🎉🎉

[@dustinh4175]

@@grendelsgarage9723it was quite the ordeal but I used the wider roller from a spring tensioner but I had to make a bearing spacer from an old 12mm piston pin to keep the bolt from crushing the bearings together as the spacer from the factory is aluminum and too large in diameter. So if your willing to do the work its a good setup. The 12mm pin is hard as f and a hacksaw wouldn't even scratch it. A dremel with a cutting wheel worked fine. Between the wider roller and two crescent wrenches to twist the arch it lined up perfect.

[@dustinh4175]

@@grendelsgarage9723 kzbin.info/www/bejne/hoqWdaR4oad1f68&si=oemZgIY4BfjcWsUK

[@dustinh4175]

@@grendelsgarage9723 I tried to leave a link to a video I made but idk. It's on my channel if your interested

[@SuperTrikeBicycle.]

Sounds good. Expansion chamber really helps. What spark plug do you run?

[@grendelsgarage9723]

It's like a new bike with the pipe! I'm running NKG 8R... not ideal the (8R). Bought big box when I got into the hobby and I'm trying to use them up. Probably is NKG makes dam good plugs so I'm not using them up fast hahaha 😅😅😅😅🎉🎉🎉

[@SuperTrikeBicycle.]

@@grendelsgarage9723 for sure any NGK is usually a great plug.

[@Paul_Gale]

i want one sounds amazing my 66/80 China doll with a 36 t sprocket does 40 mph (down hill) and 32 tooth does 38 mph not enough power for my fat ass, just ordered a 28-tooth sprocket with 3 hole hub mount. Is that stock or have you balanced it? modify the motor?

[@grendelsgarage9723]

I wasn't sure what I was expecting when I got this motor, but I'm flat impressed. Your China doll is doing pretty good, though! Any mods? I've not ported the Avenger. She is stock minus the head and pipe. 🎉🎉🎉🎉 looking to upgrade the card next. I did have to mess with the cylinder spacing and ended up using the smolik performance 2mm spacer and 2 back gaskets to get the piston squish right ✅️. Thanks for the comment, ride safe 🎉🎉🎉🎉

[@KevinTodd]

👀👍

[@grendelsgarage9723]

❤❤🎉🎉

[@trentbikes]

Give 32T a try lmao. On 10/36T it topped out 10k for you. You may get close on 32T, going around 55mph.

[@HarrisonBlackwood-ls2vj]

he needs a pwk21, that expansion chamber is being bottle necked.

[@trentbikes]

@@HarrisonBlackwood-ls2vj I'm gonna have to agree. I'm sure with a bigger carb it will scream harder and go over 10k.

[@SuperTrikeBicycle.]

I tried 20 22 and now 24mm none of them did any better that the stock bofang. The expansion chamber and timing key was the only thing that helped. Without porting there's not much more you can get out of the Avenger and it's pretty much ported all it can be. Yes 32t will help but then your riding the clutch all the time with the saw motors

[@trentbikes]

@SuperTrikeBicycle. uhh you don't need to go bigger than 20-21. Like at all. Also it's probably because of your tuning. You need to tune them, add more fuel. And don't bottleneck the intake setup.

[@SuperTrikeBicycle.]

@@trentbikes my Avenger 3 wheel bicycle on video runs 53mph. I think I know how to set it up.

[@theLyzhendricks]

16:57 i would have thought it blew up 😂

[@grendelsgarage9723]

Me too!!! 😂😂😂😂 I was like well it's over hahah 😅

[@LazloNQ]

Using a GPS as a speedometer has always netted me 2mph error because gps can't take into account your speed over 3d dimensional terrain so I bet you hit 50mph on this run.

[@grendelsgarage9723]

That makes sense what you're saying about the GPS info. Thank you for that. I should look into upgrading so I can be more precise.

[@theLyzhendricks]

20:19 ngl i wpuld have pulle din the clutch and revved it a few times 😂 im petty lol its literally my familys last name

[@grendelsgarage9723]

I thought about 😅😅😅. In my head, I was like bro this isn't even a loud pipe. My nasty jack on the other hand is dam loud 😂😂😂

[@kennethlloydr.sentino934]

Are younusing stock 44t sprockets?

[@grendelsgarage9723]

Running a 36 tooth sprocket. My town was built on a long hill, so I dropped all my bikes to 36 tooth sprockets.

[@Julian-wg1jf]

Does this engine come fully assembled ready to put on or do I have to put it together? Just curious

[@awakenotwoke2643]

Fully assembled,just add carb.

[@acorncz4752]

I know that phantom 85 is quite loud even in stock but this pipe on this motor gotta be a ear ringing device. I only had a mz65 clone on a yd100 and had to make a silencer for it or else i woud have my ears ringing for a day after each ride.

[@grendelsgarage9723]

@acorncz4752 you know what is weird? My Nasky Jack pipe is much louder than this gomax pipe. 🤣🤣. The gomax pipe is better built, though. Brother, I used to run silencers all the time, but traffic has been wild the past year, so I stopped. It's not good for my ears 😕 but people hear me coming even in their cars.

[@acorncz4752]

@@grendelsgarage9723 oh yeah that's a legit reason why i considered riding without a silencer. But i didn't have any trafic trouble yet. I also wanna stay quiet for the cops. They are a bit too serious around here...

[@grendelsgarage9723]

@acorncz4752 I respect that 💯 🙏. So far the cops have been chill over here, but I think ebikes are changing that quick in my area. Ride safe 🙏

[@acorncz4752]

@@grendelsgarage9723 yeah ebikes are getting out of hand... Ride safe too bro.

[@nathanroberts6315]

What style mz65 pipe is that? The side or the belly?

[@grendelsgarage9723]

This is the side exhaust pipe from gomax industry. Just a heads up. I did have to use a floor jack to bend it to fit my ride.

[@nathanroberts6315]

@@grendelsgarage9723 thanks man. Imma try a torch.

[@nathanroberts6315]

@@grendelsgarage9723 did u get the whole set up from gomax

[@SpAcEcruizer203]

Any link for a good motor i had a pk80 once upon a time long ago def miss the hobby been stuck on this 212 eversince she went on me i was running a 44tooth and kept high reving it to hell 🙃

[@grendelsgarage9723]

hybridpowerbikes.com/collections/engine-kits

[@grendelsgarage9723]

I would recommend these guys. Its Basically, where I got this average 85. Best bang for your buck right now 👏 🙌

[@grendelsgarage9723]

I think smolik performance also sells the Avenger 85 as well now. I would be hard pressed to buy anything else short of a Mineralli kit, but a good one is like 500 plus...

[@SpAcEcruizer203]

@grendelsgarage9723 thank you bro 💪🏼💯💨💨💨

[@SpAcEcruizer203]

@@grendelsgarage9723 200 bucks 💪🏼 so do I have to check if the tings are on correctly and all that or is it plug n play