Fusion How-To: Design Your First PCB

Fusion How-To: Design Your First PCB | Autodesk Fusion 360

Рет қаралды 49,413

Күн бұрын

Welcome to this Fusion 360 Electronics tutorial! In this KZbin video, our Fusion 360 Electronics guru Ed Robledo will be demonstrating how to create a Printed Circuit Board layout, or PCB. The video will start with a schematic design and create the PCB by editing the outline shape, placing components, and routing the signals.
This Fusion 360 electronics instructional video will guide you through creating a Printed Circuit Board (PCB) using the schematic provided in the first walkthrough video. If you haven't watched our Create Your Schematic video yet, click the link in the video or go here: • Fusion How-To: Design ...
►FREE TRIAL | autode.sk/3Wtfi20
►SUBSCRIBE | autode.sk/30njGGX
►GET STARTED | autode.sk/30k2DWh
►TRY AN EXTENSION | autode.sk/3EOUidW
CONNECT with Fusion 360 on social media:
INSTAGRAM | autode.sk/2Enzh8P
FACEBOOK | autode.sk/19jII5A
TWITTER | autode.sk/19jIJXc
LINKEDIN | autode.sk/3UyieZS

Пікірлер: 22

@BleuDrache Жыл бұрын

Thanks! With videos like this, I feel a bit more comfortable using Fusion 360 for electronics. So far, it was a magic block box.

@impexllc9866 Жыл бұрын

Ed Robeloddo, Is possible to have the back screen on 100% BLAK not gray type?

@mechanoid5739 7 ай бұрын

Is there an option to produce a layout using Varo/strip board?

@matheusorofino9980 7 ай бұрын

Brabo

@myroadtospace 5 ай бұрын

Great…

@jeffhulett4194 Жыл бұрын

does fusion 360 allow you to have the schematic on one screen and the PCB on a second screen?

@EdRobledo Жыл бұрын

Hi, yes it does.

@MindstormExpert 6 ай бұрын

Can someone tell me how you get the 3D PCB component to align with features of the mechanical case? For example, if I have a faceplate with some holes in it for switches to go through, how do I align the PCB component to the mechanical feature hole on the faceplate? The steps I have got to so far: 1. Created a 3D model of a box with a faceplate, which consists of holes for the buttons to fit into. 2. I have drawn a sketch of what I want the PCB outline to look like within my design workspace. 3. I have selected the option 'Create Associative PCB' and selected my PCB outline, whilst leaving the holes unselected so they appear on the PCB. 4. I have then allowed it to take me through to the 3D PCB workspace where I then pushed it to 2D workspace. 5. I have selected my holes and put them onto layer 51 'Document Top' so they can be referenced. From here onwards I went about creating a schematic and then placing my components onto my 2D PCB. However, this is where I am stuck and have no idea how to get my 'footprints/pads' of the button components to align with the centre of the holes. Any advice or videos I should watch? @Autodesk Fusion Thanks in advanced.

@EdRobledo 5 ай бұрын

Hi @MindstormExpert I hope all is going well. Please post your question on the Forum. Thank you. autode.sk/482fR7q

@mehfoozzansari Жыл бұрын

I dont have basic knowledge of electronic or circuit.. But i want to learn as an hobby.. Please guide me with some free learning resources from basic to advance.

@adskFusion Жыл бұрын

Check out our Fusion 360 Electronics for Beginners playlist if you’re looking for somewhere to get started! kzbin.info/aero/PLmA_xUT-8UlL80Xm8Gxz98YNum3I9GInr

@EdRobledo Жыл бұрын

Consider visiting www.instructables.com/Electronics-35/

@jackflash6377 5 ай бұрын

Casually resizes the board with no indication of where to set the size of the board. I need 39mm x 50mm with 2mm radius corners. Where to set this? I don't even see a display of what size is being set.

@troybakker7628 4 ай бұрын

I know i am a bit late but its under design, then board shape (you can delete the old lines first if you want to) and then you can draw the general outline (square, rectangle, L shaped or something else) and after that you can make rounded corners with the board shape tool and then remove the excess lines outside the curve. Hope this helps

@jackflash6377 4 ай бұрын

@@troybakker7628Thank you kindly.

@robertgogol289 9 ай бұрын

How to resize PCB board?

@EdRobledo 5 ай бұрын

Hi @robertgogoI289 thank you for your participation. You can simply left click and hold any asset on the PCB to select and move it. Just as it was done on the video.