FX IMPACT M3 SLUG SETUP TEST WITH HARMONIC BARREL TUNER SHROUD

[@hurricaneaquatics]

Thanks for the video. Saved me some money on Zan slugs. I know you had to cover it up a little, but the Patriot and the JSB shot twice as good as the Zan.

[@raysimon1368]

That is some great shooting love all your videos very professional no stupid clowning around just great information thank you very much keep em coming on the impact need all the help I can get

[@Airbuks]

Thank you for the support 👊

[@jerryking3208]

Thank you. Haven’t been able to get any consistency with 22 slugs in my stock M3. Was going to try a carbon sleeve on the stock barrel, but looks like I need to spend a bunch more and get the heavy liner, sleeve and tuner.

[@Airbuks]

Hi mate , before you go ahead and spend a bunch of money I would advise you to try the following first . 1 I don’t know what weight slugs you want to shoot but the superior liner can shoot slugs aswel but you will have to choose a lighter one from a softer lead . For instance the Javelin , ZAN , JSB . Try a 25gr or less in a .218 size 2. Try to get a very consistent fps tune to about 960 , then go out and shoot at every setting on the powerwheel ( velocity tune to find the best harmonic) to see what velocity you get the best accuracy. This should be able to allow you to shoot slugs with the original configuration and have decent results My setup and all the extras is build to shoot some heavy slugs at fast speeds

[@jerryking3208]

Thank you. I have 20grn up to 26grn. You are right about the 218 sizing. They are better but still not good enough for squirrels or pesting and always some flyers. Thought I’d get the carbon liner first and see how it does and if needed keep adding till I find the sweet spot. Your advice is invaluable and I appreciate it.

[@Airbuks]

@@jerryking3208 you’re welcome mate , keep met posted

[@farmer_giles_uk]

Try FX Hybrids. I have an off the shelf impact m3 700mm .22 and I have the second reg at 115 I set the slider at 4.0 and open the valve one and a half turns past line 4. I have rotated the barrel so the slug port is facing down. In this config it gives 1,000 fps +/- 3fps and every slug through the same hole at 30yards. This should be good for squirrels. My scope is high at 3.3 inches bore to centre scope, so I’m within 1/2 inch of the crosshairs from 20 yards out to 60 yards

[@Airbuks]

@@farmer_giles_uk oh yes indeed , I forgot about the hybrids 👍🏻 they are designed to work in a normal superior barrel

[@precision_Air]

I'd like to see the differences between the tuner and it taken off for the given slug weight. To see the actual improvements.

[@Airbuks]

Hi Bryan, there is no point in doing this as I can get good accuracy without it . But then I need a different tune and the gun choices the velocity to be accurate, with the tuner I choose the velocity I want to shoot that ammo and correct the harmonics with the tuner. If I would just remove the tuner now and shoot my groups would be opening and shifting position , I know from previous experience that my barrel likes to shoot 30gr slugs at 930fps what I found to slow , now with the tuner I was able to boost the velocity and still get the accuracy

[@crazy-eyewoodguy4489]

Thanks for taking the time to make this. One question: To me, the harmonics should (will) change from one pellet maker to the next. I think you got lucky with not needing to re-tune the tuner for each slug. Even though you are keeping the velocity close the weight difference and just how the slug contacts the liner with change the harmonics. I only mention this for guys that may be new to the sport. Don't give up if one slug shoots well and the other doesn't. Try re-tuning for the slug specific. Another thing to consider when shooting slugs, one may be more stable at a particular velocity. Im sure the gentleman in the video probably knows this (may even have it in another video) but it wasn't mentioned. I hope I didn't sound like a troll 😬

[@Airbuks]

Hi mate , I 100% agree with what you wrote 👍 I tuned the gun in the video for the ZAN slug and wanted to test to see if similar weight slugs also would benefit from the harmonic balance of the slug I tuned it to ( I wasn’t expecting to get good groups as harmonics are so fuzzy with slugs ) but somehow the did group wel . Maybe luck or not 🤔 wil need to investigate that maybe. Normally I tune my guns ( in other videos) to a certain consistent max velocity and then I look for the best accuracy in velocity by going down on the power wheel. The harmonic tuner need a consistent velocity that you choose and from there you use the tuner to fine tune the groups . Ps : you didn’t sound like a troll 👍😉 I love some constructive talk

[@Donny_Juanny]

I love the sound of the power plenum filling up after each shot. Sounds like Darth Vader.

[@Airbuks]

I like it to , it gives me also a timeslot when to shoot the next one 😉 Some people hate it though 🤷‍♂️

[@SuperBenjamin1965]

I picked up the wildcat three compact in 30 and I can say I’m very pleased with velocity in foot pounds with heavy slugs having the option to tune Feet per second I keep it on Settings seven with a Ronin Hawk digital reflect I’m getting superior accuracy at 75 to 100 yards FX hybrid as well as Nielsen specialty slug nice set up Take Care

[@Airbuks]

Love the wildcat! Great gun aswel 👌🏻

[@panayotisantypas3828]

Hi ! Thank you very much for your nice video once again.You are a very big help to all of us Airguns shooters. I have configured my gun exactly like yours.Love it and shoots so well.The FX guys have really manufactured an airgun with precision never thought before at long distances up to 150 mt My set up likes very much the H&N 25 and 27 gn both .218 at speeds 970. I can’t understand why such differences between.217 & .218 ..🤷‍♂️🤷‍♂️ Thanks again my friend

[@Airbuks]

Hi , I love that setup aswel ! The difference in sizes have to do with mating surface with the liner or barrel . Generally the .218 work best with lighter slugs and .217 is better for slugs 25gr and up . I wil give the H&n slugs a try aswel 👌🏻

[@sambaaxe]

It would be interesting to see what a pellet of the same mass and shot at the same velocity would do. My feeling is that since a slug will have less bearing surface in contact with the barrel, it would impart less of its energy to the barrel, and thus produce a slower moving and/or lower amplitude harmonic wave. Certainly worth a look!

[@Airbuks]

Thx for the tip ! I will give it a try in a upcoming video 👍🏻

[@tomlpnexus]

Congratulations very good groups and information. In my Impact with the pressure of the regulator at 170bar it throws the slugs well above 1040fps, I close the air passage little by little until I leave it in the 2nd line at a speed of 990fps with the 49g Zan with a excellent precision, I notice much less vibrations in the gun with high pressures, since the valve is quite closed, an exact amount of air comes out and the valve closes quickly for the high pressure in the plenum, I could not explain myself, it is the closest thing to a detonation of a firearm, with which there is no residual air behind the Slug, i feel the gun works nice with this short amount of air but in high pressure.. I have installed ; Slug power kit .30 Huma Dual transfer port Huma regulator gen2 extra high pressure Harder Hammer Spring Heavy hammer weight 700mm liner superior heavy Is the mk2 but i have installed the 72cc plenum and 63cc external plenum from vladam. I love this gun 💯

[@Airbuks]

Sweet , thx for the info 👍🏻

[@darrelldixon1067]

Nice sir I like your videos Very detailed And not cluttered keep them coming 👍 And your tuning videos 💯🏁🎯

[@Airbuks]

Thx mate for the support, much appreciated

[@Lottus__]

Always had a good videos as always

[@Airbuks]

Thx 🙏🏻

[@fliesarenegade]

Now, that are some nice groups!

[@Airbuks]

Thx 🙏

[@airguns_rc]

I am liking your videos. i am tuning my M3 Impact ,22 caliber shooting the 31.2 grain NSA slugs that the barrel liner likes. The standard superior and the heavy superior. My set-up is very similar to yours. Subscribed.

[@Airbuks]

Thx for the support mate 👍

[@12VALVETORQUE]

great video, thank you. I have not yet had the chance to experiment with my barrel tuner, I am sure you just saved me a lot of headache in the process. can you please let us know what your full setup is? that would be very helpful.

[@Airbuks]

Thx , I really like that tuner so much easier to harmonic tune the gun . 1st reg at 180 2nd reg at 145 Macro 16 Micro 3 Valve at line 4

[@12VALVETORQUE]

@@Airbuks thank you. very much. I think I must have something wrong with my M3. shooting 30grn .218 Javelin's at 942 fps average 1st reg 205 2nd reg 160 macro 16 micro 4.5 valve 4.5 ?????

[@Airbuks]

@@12VALVETORQUE 🤔 first idea is that it’s overpowered and out of balance. Do you have the slug power kit installed? I do , maybe I forgot to mention it in the video 🤔

[@12VALVETORQUE]

@@Airbuks I have 700mm Superior Heavy, pellet probe, (had the full power kit in but lost 100fps Utah air told me to take out the power kit but leave the probe. so I did. 185 bar, 150 bar, 16, 4, and valve at line 4, 710 fps ) I was so concerned with the low velocity I sent it back to Utah Air to have them look at it. they sent it back to me with the first mentioned settings 205 bar etc... at 942

[@Airbuks]

@@12VALVETORQUE 🤔 that doesn’t sound like it should perform. After installing the slug power kit you will have to turn your tune down or you risk overpowering the valve and your tune will be out of shape .

[@pst2147]

Really impressive. Thanks for your work.

[@Airbuks]

Thx , appreciate the comment

[@JuanDoe1776]

Great video. I’m more interested in your shooting table. Do you have a video on how to make one or who is the manufacturer?

[@Airbuks]

Hi , thx for the comment 👍🏻 The manufacturer of the shooting table is my father in law 😉 he found these plans on the internet. If you send me a email ( [e-mail] ) I can give them to you 👍🏻

[@concepcioncarvajal4953]

Me gusta mucho tus vídeos.no te entiendo nada, pero bueno,me gusta mucho verlos

[@Airbuks]

Thx mate , appreciate the comment 👍🏻

[@tld-airgunsalafrancaise5965]

Thank you so much for sharing your knowledge. Your barrel is the stock one and liner too or you changed them with the carbon ones please ?

[@Airbuks]

Thx 🙏 this is a slug liner with CF sleeve

[@shiftpodoverlandadventures]

Hello, I love your videos keep them coming. Where did you get your shooting bench at, I would like to get one?

[@Airbuks]

The bench is a diy project , I get many questions about it and will make a video very soon and I will share the plans aswel

[@nephtalilucero8084]

Can you do a 75 yard trial? Also with out the harmonic barrel what would be the grouping with everything else the same? Those are awsome groups but i would be interested in longer distance. How heavy is the harmonic? Much thanks!

[@Airbuks]

Yes , in the next M3 video I will stretch it out to 75 ( max on my range ) or 100 if I find a place to go shoot with that distance. I wanted to include the 75m in this video but it was very cold and since I just recovered from covid I didn’t had much energy left after filming this 😉

[@AirHeadArms]

Great review, thank you and happy shooting 😊

[@Airbuks]

Thx 👊

[@justinhromek73]

Awesome vid! I appreciate you sharing you results and hard work. Have you been able to get your hands on the new 25 cal knockouts with a flared skirt? Those have me excited, I’m hoping they shoot well out of the m3 with the standard superior liner. It shoots the 33.95 mk 2’s excellent with that liner and I don’t want to change to a slug liner and lose my pellet accuracy.

[@Airbuks]

Thx for the support 🙏🏻 those are the comments that keep me going ! I have heard about those flared slugs on a video coverage of shot show so I think they aren’t available yet . Soon as they are I will try them for sure . But slugs made from soft lead might work also in the normal superior liner , there is not harm in trying it , they won’t damage your liner 👍🏻

[@justinhromek73]

@@Airbuks I appreciate your response! who makes what you would consider softer lead? My thoughts are Most slugs fit so loosely that I don’t think they get influenced by the grooves in the liners. I’ve tried some avs .2513 and they grouped better. Do you think the 254 diameter is too large for a superior liner?

[@Airbuks]

@@justinhromek73 🤔 javelin slugs are pretty soft lead but only come in 22 cal The JSB should also be oké I guess

[@fishing4happiness610]

Your vids are next level. I've never seen anyone else notice, but you use 2 grip styles(thumbs up high grip and standard full grip. How do you decide which grip to use? I used your high grip style and my groups have really tightened up and the cocking is faster and more natural. Keep the vids coming!

[@Airbuks]

Hi , thanks for the support! My grip style depends somewhat on the setup I am shooting and how it’s tuned . For high power setups with high regulator settings I tend to get better accuracy with the thumb up and high on the grip , lower power setups are much more forgiving.

[@fishing4happiness610]

@Airbuks ... Thank you, this explains why your thumbs up method works for me. My .30 Mav Compact is set at 180/150 and is lights out with FX Hybrids traveling at 910fps at my limited 75 yard range. Do you squeeze your thumb and your trigger finger together (lemon squeeze) for the shot... that's what I'm doing. Thanks again!

[@Airbuks]

@@fishing4happiness610 I slightly put pressure with my thumb against the action , for some strange reason it gives me a more steady aim and better trigger control 🤷‍♂️

[@fishing4happiness610]

@Airbuks ... Agreed, looking forward to more good stuff!

[@daiwangel]

good afternoon, I really like your fx rifle, I ask one thing about your July 16 or July 24 rifle, or apart from that, do you buy parts with more power? I speak little English badly from Spain

[@Airbuks]

Hi , what do you mean with July 16-21 ? My M3 is one of the first ones produced if that’s what you ask ? I have made some power upgrades in the form of the slug power kit , you can find that video on my channel aswel

[@vizner124]

Great video, thank you. Can you share your thoughts on Harmonic Barrel Tuner? Does this work for 0.22 caliber only, or will it work for 0.25 and 0.30 calibers as well?

[@Airbuks]

Thx , so far I am very pleased with it allowing me to choose the velocity to shoot a particular ammo . Any it will work with any caliber 👍🏻

[@simoncoher4841]

Hi mate great video , Glad you are feeling better, Are you going to do any testing with The .25 using slugs ?

[@Airbuks]

Thx mate , for the moment I am focusing on 22 cal and still want to bring longer ranges before I swap to 25 again

[@simoncoher4841]

@@Airbuks Oh OK mate that's fine Still love the videos and your content you put out so makes know difference I hang tight to you get the .25 back out ..

[@Airbuks]

@@simoncoher4841 thx 🙏🏻

[@panayotisantypas3828]

Hi! Grate grate instructional video! You are always showing us the way with everything that has to do with FX a impact guns. Thank you very much!!! Is your barrel 700 or 800 mm??

[@Airbuks]

Hi thx for the support, this is a 700mm barrel 👍🏻

[@panayotisantypas3828]

Thank you so much for your immediate response.Appreciate! Do you think the 800 mm is worth for shooting slugs up to 170-180 meters? I have mine with 700mm harmonic tuner heavy slug liner carbon fiber sleeve(as you recommended without glue) and original suppressor and shoot H&N 28 gr Slugs. At 100 meters I get 1 inch groups. Thanks again for all you fantastic videos.I have learned so much mor these amazing Airguns . I have been a Professional Hunter in Ethiopia for many many years and now ready to retire in Kefalonia island in Greece.These guns are becoming a virus passion!!Hahaha

[@Airbuks]

@@panayotisantypas3828 😂 airguns are very addictive 👍🏻 Regarding the barrel length , if you don’t need extra speed to shoot heavy slug and you can archive what you want with a 700mm you don’t need the 800mm in my opinion. If you want to shoot 22cal 40gr slugs at 1000fps yes I would advise it . The extra barrel length of the 800mm also gives extra room for shooter error as the slug or pellets travel true the barrel is a bit longer and trigger control becomes even more important . I have requested a 800mm at FX to find out more 😉

[@panayotisantypas3828]

@@Airbuks Hi again my friend. So nice to receive your reply. I will wait for your tests and then see if it is worth buying. What do you think about the 700 cc carbon fiber bottle.Should I consider it ? I once again would like to thank you for your help .

[@Airbuks]

@@panayotisantypas3828 the 700cc is nice when you shoot from the bench as it gives you quite more shots before dropping if the regulator. Look wise with a 700mm barrel is also good in my opinion. If you hunt and carry your gun a lot I would stick to a 580cc max With the 800mm I think it’s best to have a 700cc even just for looks

[@EdBraunbeck]

Great instructional video. Out of curiosity, What are your second regulator and micro wheel settings for the 25/30 gr slugs? I know results will vary since you mentioned several mods are installed.

[@Airbuks]

Thx , the settings I use are 1st reg at 180 2nd reg at 145 Macro 16 Micro 3 Valve at 4

[@hakansoderkvist1533]

Great video. Where did you get that bench? What's the name of it?

[@Airbuks]

It’s a diy project of my father in law

[@hotchihuahua1546]

My question ? Is it repeatable if you switch back & forth with slugs & speed to the setting that gave you a tighter groups with the harmonic balancer .

[@Airbuks]

After I recorded the video I turned it back to shoot some 30gr with the same accuracy as in the video

[@precisionairgunninghunting6265]

Great video, could have been better if you did a before & after though. My MK2 groups the same without ANY mods to barrel or a tuner.

[@Airbuks]

Thx , I understand the point you make . But i to get those results without the harmonic tuner but then I have to look for the most accurate FPS to get those results, with the tuner I can choose the velocity I want any tune the harmonic node with the tuner .

[@precisionairgunninghunting6265]

@@Airbuks that's the concept of the tuner, select the speed you hope for & then tune. Glad it worked out for you 🙂

[@Airbuks]

@@precisionairgunninghunting6265 me to 😉 but I must say a good basic tune is recommended to get it to work properly

[@precisionairgunninghunting6265]

@@Airbuks agreed, some think its all that's needed 🤣

[@Airbuks]

@@precisionairgunninghunting6265 yes I have the feeling some people think it’s like a magic wand to make there gun shoot superior 🤣

[@airriflehunter87]

Nicely done mate 🔥👊

[@Airbuks]

Thx mate

[@brocwavra8813]

Hello there I am just now getting back into shooting again,...I received my custom RAW 1000 x in 25 cal. I ordered my ATS tuner and wondering what distance you are using your tuner at? I am only shooting pellets. I am hole in hole at 40,50 and 60 yrds. But once I get out to 80 yards and further I start to lose accuracy. Should I be dialing in the tuner at 80 to 100 yrds? Also is it okay to be shooting pellets out that distance or should I be switching to slugs ?

[@Airbuks]

Hi , yes I usually set the tuner in at 75 m . It is quite common for pellets to shoot hole in hole at 50-60 but once you stretch it 25 m extra pellets get affected by the elements of wind etc . You could go to slugs but that’s a whole other ballgame 😉 and hard to tune .

[@lbtn1]

Love the accent!! Where are you from brotha?? You remind me of Djokovic!!

[@Airbuks]

🤣🤣👍 thx mate I am from Belgium , where are you from ?

[@lbtn1]

Patagonia, Argentina!!! Love the channel!!

[@Airbuks]

@@lbtn1 🙏

[@biakmawia]

My mkii with 23grain H&N Slugs i can easily shoot group under inch easily @100m but i realy like to try the harmonic tuner......

[@Airbuks]

Sweet 👍🏻 with lighter slugs at a little lower velocity it’s much easier to get better groups as you don’t have to push the gun as hard , maybe I will make a video with some lighter slugs to compare. Thx

[@volkanoadams811]

hello first thank you very much for information just i want to know the shroud 700 mm total how many cm? thank you

[@Airbuks]

Never measured it 🤔 I just ordered one for the 700mm barrel 🤷‍♂️

[@villaman2261]

Lighter ZAN slugs 21 , 23 and 25 217slugs work faultless

[@Airbuks]

Next video I am going to try the 28,5 Gr 👍🏻

[@masonskeels6638]

I have a 22cal fx impact m3 what speed should I shoot 34gr Zan slugs at?

[@Airbuks]

My impact 800mm likes them at 980fps but my Maverick 700mm likes them at 960fps

[@masonskeels6638]

@@Airbuks thank you so much you are so helpful

[@ArturoGarcia-kx8pq]

It's better still if you shoot each slugs with out the barrel tuner and see the difference. Thanks.

[@joostvanleersum4332]

Always that damn flyer 🤣 Nice video. Thanks again!

[@Airbuks]

Yes indeed , specially when filming 🤣 but I try to show the real world not one elusive group of the whole day

[@saviofalcao670]

Hi. Can fx impact barrel fit fx maverick ?and also pellet probe thanks

[@Airbuks]

The barrel can be used on the Maverick but the probes are different

[@saviofalcao670]

@@Airbuks thank you very much for your reply

[@phillipclark4027]

Great tune Hey have you ever heard of the m3 not making the refill noise? My m3 .22 700mm with the power block 1st reg 170 2nd 145 I take a shoot and it does not make the refill sound but it also fills back up to 145 Fx USA Tech said don't be worried He has had customers call on similar issues. He also said the plenum tolllerence can be different What do you think?

[@Airbuks]

Mmm 🤔 interesting, my both impacts and Maverick have the refill sound . I think if you don’t use air enough the plenum might refill just a tiny bit that doesn’t make noise . If you have that regulator at 145 what is your micro ,macro and valve at ?

[@phillipclark4027]

Micro 3/12 macro 15 Just wondering if because I did over fill the bottle about 40psi over which probably put a strain on the first reg if that had something to do with it. But it does sound like I'm not using a lot of air so it a very little to refill. I'm going to bleed the system and rest the regs to see what happens. Fx USA did say I had nothing to worry about if my fps or poi haven't drop Just use to the refill sound and it's recking my nerves to know if everything is ok

[@Airbuks]

@@phillipclark4027 what is the projectile you shoot and velocity you try to get ?

[@phillipclark4027]

Good dat my friend I'm shooting 31.2 Nelson I de-gassed it yesterday Brought it back up 175 front 150 rear 1000 to 1005fps over 15 shoots The refill is perfect now. Guess it was still breaking in. I was use to my maverick But this is a whole different beast Micro 3 macro 13 valve 3 and a little bit Dime size groups @75yrds now Any plus or minus on the tension kit that no one can get at the moment but the big guys Like yourself 😉

[@maverick25100]

Could you say where you got your shooting table at?

[@Airbuks]

It has been made by my father in law

[@jacopienaar9157]

hey bud hope you are doing well. could you please tell me do u set the volocity u want and then use the hormonic shroud to get it acourte?

[@Airbuks]

Yes that correct, the key is to get a nice and tight spread in the velocity

[@michaeleber4752]

I'm puzzled why you left your scope off center. The movement of your hits on a mostly vertical change then you need to change zero. That way you aim directly at the center of the bull and then your slug hits in the center of the bull.

[@Airbuks]

De aim was group size , not to be perfectly in the Bull . When shooting groups/tuning I often do that as I keep my point of aim and get the best idea of group size . If my first shot lands in the bull the point of aim is comprised

[@michaeleber4752]

@@Airbuks Understood. As a competitor I keep adjusting for POI and then toss out any brand that fails to remain on the bull. I''m also a trained sniper and we always adjusted for POI when performing our zero testing and load adjustments. Habit which bugs me when watching others. LOL

[@Airbuks]

@@michaeleber4752 complete understand 😉👍

[@numizaairguns1373]

it's interesting and great job

[@Airbuks]

Thx

[@FireTheHoker]

Are you gonna get one of thoose 700cc 300 bar bottles ?

[@Airbuks]

Maybe I am not sure as I find it looks abit out of shape with that long bottle 🤔 but that might be oké when the 800mm barrels come out 👍🏻

[@Airbuks]

Maybe I am not sure as I find it looks abit out of shape with that long bottle 🤔 but that might be oké when the 800mm barrels come out 👍🏻

[@FireTheHoker]

@@Airbuks Do you think you could push 35 cal slugs to above 900fps with the 800mm barrel, the slug power kit and the 300 bar bottle to allow higher rear regulator pressures ?

[@Airbuks]

@@FireTheHoker yes for sure , I have got reports from people shooting 80gr 35cal between 920-940 fps But I don’t have any personal experience with that

[@FireTheHoker]

@@Airbuks If thats true I'll definitely get a 35cal

[@nicoso71]

What is that shooting bench?

[@Airbuks]

I have a video with free plans about that

[@NoName-gq5ic]

Does the mk 2 magasin fit the m3 ?

[@Airbuks]

Yes 👍

[@emmerichweinlich1057]

I have a big problem with my new FX impact M3: It can‘t hold Pellet/Slug velocity. I adjusted the gun at Reg2 pressure at 140 bar, Macro 16, Micro 4 and Valve 5.5 to an average speed of 960 fps with FX Hybrids 22 grains. After shooting 5-10 shots with accuracy, accuracy issues were starting with according shots so I measured the speed again and it was only 890 fps I completed shooting without any tuning and finally the speed was 802 fps! I checked tank pressure 200 bar was O.K and power plenum Reg2 steady at 140 bar. Nevertheless I refilled tank to 250 but but speed was now only 790 !! I adjusted valve and hammer spring again to reach 960 fps but the same things happened again, loosing speed with any further shots. Any ideas what’s wrong and can be fixed ??

[@Airbuks]

Sorry for the late reply, I am wondering if the C1 isn’t backing out by itself 🤔 In the older models it could be that the hammerspring adjustment was backing out but on the M3 I think that’s not possible. Do you know what’s the C1 ?

[@emmerichweinlich1057]

@@Airbuks What do you mean with "C1" ??

[@Airbuks]

@@emmerichweinlich1057 the C1 is that part that sits on the end of the valve rod when you remove the valve adjustment know

[@emmerichweinlich1057]

My last adjustments with Huma Slug Kit: Reg1:164-166, Reg2: 124-126 (both Sekhmet Digital), Makro 16, Micro 3.5, Vo= 977 with FX Hybrid 22 Slugs at Home fairly constant, but at the Range dropping down to 820 fps after a few shots now.

[@Airbuks]

@@emmerichweinlich1057 🤔 strange , few things to ask and determine. Are you shooting in much colder air the the tests at home Are you shooting at a much higher or lower altitude then testing at home Is the regulator pressure the same even with the lower velocity

[@romanmarkin4476]

Could you please tell the caliber and share the set up?

[@Airbuks]

Hi , yes offcours ( I think I mentioned the caliber in the video 🤔 ) but it’s a 22 cal 1reg-180 2nd reg 145 Macro 16 Micro 3 Valve 4

[@romanmarkin4476]

@@Airbuks thanks a lot for info chief!!!

[@t206n]

What length is your barrel?

[@Airbuks]

In this video it is a 700mm

[@roypijnenburg9854]

Nice video, but i can do this without the tuner. So for me it isn't a big improvement for acuraccy.

[@Airbuks]

Yes indeed, I can also archive the same results without the tuner but in order for the gun to get to that accuracy level the gun dictates at what velocity I have to shoot a particular ammo .The whole point of the tuner is that now I choice the FPS I want and the gun , so with the tuner I can change the harmonic node by shifting the weight and without the tuners I have to change the velocity to archive the correct harmonic node . I hope my explanation makes sense 🤞🏻

[@Chumbuucket]

hard to shoot groups when you don't zoom in...

[@Airbuks]

What do you mean ? Target was at 50m and the Titan scope zoom was at 20x I believe 🤷‍♂️ I am just using 2inch targets 😉 so it might look like that

[@nicolaslempereur2884]

Merci pour cette vidéo

[@sonan7216]

Ha sido muy divertido oírte decir por supuesto tengo que arruinar el grupo, animo cajas, cajas y mas cajas.

[@Airbuks]

English please 🙏🏻

[@sonan7216]

@@Airbuks It was so much fun to hear you say of course I have to ruin the group, I encourage cans, cans and more cans lots and lots of cans, thank you.

[@Airbuks]

@@sonan7216 👍🏻🤣

[@BKKNOW1]

You’re nearly as good as me shooting my Theoben 12 lb 22, all the air gums today are copied from the Theoben.

[@Airbuks]

Hi mate , thx for the reply 👍🏻 . We as airgunners can be lucky there are many great airguns on the market 👌🏻

[@BKKNOW1]

@@Airbuks your right mate some great air guns made now, my next gun will be the FX.

[@aburaeese]

my prognosis after watching this is ; you do not have blocked arteries!

[@Airbuks]

😅 what do you mean , the shaky scope cam ?

[@aburaeese]

@@Airbuks yes! Correct. 😆

[@Airbuks]

@@aburaeese as I mentioned I just recovered from covid and it was cold 😅

[@aburaeese]

@@Airbuks hopefully you recover from your illness. excellent groupings by the way.

[@Airbuks]

@@aburaeese thx 🙏🏻

[@seyhmusaltunsoz3675]

👍

[@Airbuks]

Thx

[@copyandpaste6485]

I wish i hve an m3😪

[@Airbuks]

I feel you mate 😔

[@copyandpaste6485]

Im a big fan of yours brother. Keep it up.😪❤

[@Airbuks]

@@copyandpaste6485 thx 🙏🏻

[@johnnyventurino8947]

No disrespect my friend but look back in your videos when you were shooting your blue EDGUN LEYLA after putting your Huma regulator in it and you shot on your front lawn laying down with bipod at 50 yards. Your groups were way better with that little short barrel Leyla at 50 yards then that extra long FX barrel M3. Proof is in the video just look at it yourself.

[@midwesttacticalair7742]

See what you mean, but the leyla was shooting pellets and he is using slugs in this video.slugs and pellets normally group different but some times you can get a great combination and balance,that allows great results. Try watching some of southern Gunnar videos.he explains much better and has great content also

[@TheNickademas1]

Anyones gun will group pellets… A Walmart break barrel can group em…slugs (especially heavy slugs) are a whole different ball game.

[@johnnyventurino8947]

@@TheNickademas1 i never had no Walmart gun group pellets in a 25 cent piece at all and I had my share of there garbage years ago.

[@Airbuks]

Hi Jhonny , no hard feelings but I think your kind of missing the point of this video 😬 As mentioned above by other gentleman I am shooting 30gr slugs at 970fps that’s a whole other world then pellets , I have made made M3 shooting tiny groups with pellets in previous videos. But to get heavy slug perform like that I am happy with , lighter slugs wil perform even better . But the real benefit will be at longer ranges

[@juanrochegalisteo8895]

Round no center

[@Airbuks]

No indeed , I do this in purpose as for accuracy testing I like to be able and keep the aim point the same . If I would shoot center target I don’t see the exact aim point anymore

[@金木水火土-c8z]

不怎么地。啥也是。我就不明白50散步这么大吗？太假了 玩具送我吧

[@Airbuks]

🤨 English please

[@Anfänger123]

Spart euch das Geld und glaubt nicht alles was ihr seht!!!

[@Airbuks]

So you’re calling me a liar 🤥?

[@Anfänger123]

Ich würde sie nie als Lügner bezeichnen!!Kann nur sagen für mein Gewehr waren die Ergebnisse schlechter wie mit dem Original Lauf incl Carbon sleeve.Habe ausgiebig getestet 4 Std alle Einstellungen durch und keine kam an den Original Streukreis (kleines Schusspplaster )auf 50 Meter ran.Flyer gibt es beim Original sowie auch mit dem Harmonic Barrel Tuning!!

[@Airbuks]

@@Anfänger123 I understand a little German but could we correspond in English, so I might be able to help you with the correct information