G-Body UMI Rear Suspension Install w/ Bonus Burnout

[@dynamikbaz]

Thank you for showing your struggles. I have the same rear suspension kit for my 87 Cutlass and figured there’d be issues. So glad you showed that. Thanks again

[@raydavis5068]

You are welcome! Just like to keep it real with people.

[@poohrunna]

I have a cutlass you need some 342 gears in the rear end

[@terrylinellc5550]

Nice cutlass... I had one just like it... Cant wait to get my 87 SS Montecarlo on the road

[@mikeisaacs2314]

I had a California Regal and a rusty Cutlass wish I kept them tile was before the LS swap days

[@elreyyakko]

Following. Doing rear soon and found umi rear/front sway bars. Plan to get rear bars as well.

[@PeeCharles-cl1wk]

Subscribed thanks for videos keep them coming

[@SKD_4830]

Sweet nice video can’t wait to get mine on the road 👍🏽

[@rojelioochoa918]

Well replacing body mounts will be good start instead swapping motor

[@East_Jerome]

Thanks for the info

[@roywarren6275]

Nice video, great narration. With this setup, do you feel a need for traction bars or is it hooking up ok? Thanks

[@poohrunna]

I wish you was close by i would have sold you a rear end it just needs a pinion gear

[@mason5540]

Need to rotate those wheels after every burnout lol

[@toolbox7890]

Thx for the vid I am in the middle of rebuilding a 85 el camino and doing a frame up redo this will co.e in handy thx.is that sway bar the same or better than the anti roll bar that I have seen o. Others vid.

[@CutlassVibes]

Sweet!!

[@rasheednickson5213]

Salute to the g body nice work ..what’s the part numbers you used for suspension

[@raydavis5068]

I don’t know what the part numbers are but if you go to UMI’s website they have everything organized very nice by platform. Go to G Body section and it will show you everything you might want for all G bodies.

[@la_verde_6.0]

You need a posi bro asap beautiful built i got a 85 cutlass got a 6.0 ls for it im ready to swap !!

[@michaelmaher4328]

great video, spraying lubby doobie is far out man, pass from the left-hand side too. Lol

[@vezina808]

What part number are the Bilsteins shocks for the front and rears that you’re using? I’m planning on installing 2” lowering springs on the front and rear and 2” drop spindles of my 78 cutlass. Thanks!

[@mobiledetailingchannel2067]

Like your olds, i just put the same setup in my 1986 Buick T Type

[@East_Jerome]

What size wheels and tires

[@raydavis5068]

Below are the details for wheels. Tires are 245/40 17’s USM-U11117806145 US Mag Wheel, Rambler U111, 17 in. x 8 in., Aluminum, Matte Gray, 5 x 4.75 in. Bolt Circle, 4.50 in. Backspace

[@turbobuicknation]

Nice set up👌 did you run 17x8 with 4.5” BS on all 4 corners or is the front a different set up

[@raydavis5068]

@@turbobuicknation same size on all 4 corners.

[@turbobuicknation]

Roger that thanks 👌been all towing around a few set ups to run and sizes etc

[@shawng7902]

Im building an absolute mint ( minus paint) 85 regal. Got it cheap. Remember when people talked about building super cheap gbodys because everything was so cheap and easy to get. What happened!!!! I've got 30 grand in mine probably and I'm 75% done with it.

[@stoveguy2133]

Use a torch Melt arm bolts.

[@terrylinellc5550]

What's the width of the rear tires

[@raydavis5068]

255 40 17’s

[@kischillin5539]

Pretty sweet pile bro...

[@ja5435]

I have a 87’ Dodge Ram D150 318 small block mopar that my dad bought new and it still looks amazing and very low moles and I’ll trade you

[@MIke-ob5lx]

The wheels size and offset? And tire size?

[@raydavis5068]

Below are the details for the wheels. Including part number. I bought them from Summit. Tires are 245/40 17’s. USM-U11117806145 US Mag Wheel, Rambler U111, 17 in. x 8 in., Aluminum, Matte Gray, 5 x 4.75 in. Bolt Circle, 4.50 in. Backspace

[@CutlassVibes]

Nice Cutlass! Keep up the good work!

[@jimm8465]

1 wheel peel. Need LSD