Garden room roof and trims fitted and an amazon buy that didn't quite live up to the hype

We got the new rubber today so managed to finish the roof and associated trims.
inside has been fully insulated and is ready for vapour barrier and plaster boarding tomorrow.
I kept seeing an add for a full face mask that didn't fog up and was pretty indestructible, I should of known it wouldn't work.
If your new to the channel, we do vlogs and tutorials on all things garden room and don't take ourselves too seriously at all, its just a bit of fun ☺️

[@nyqer6636]

Loving the "OLD SCHOOL" banter and real life comments. Work is superb.

[@sueu2144]

Ignore the horrible comments people have nothing better to do! My partner is building us a garden room so I'm used to hearing all your voices on the TV. Jen I love your hair! 💗

[@autovagauto6329]

Amazing job

[@robertmorris5214]

Another excellent video Liam and the gang

[@trevordarby467]

Brilliant best on you tube by far great tradesman

[@philhode5104]

Brilliant, only 1 thing would it maybe better to have the speed sq with the lip your side,so no danger off maybe pushing it off,if you know what I mean?

[@mattjohnsonwwfc]

When are you going to upload the videos of you finishing this room off? The content so far has been very informative, keep up the good work.

[@duncaninspain]

Liam just ignore the jealousy- these are great vid and you are amazing presenting. Dont give them oxygen

[@Time2Wonder70]

A floor squeegee is good for getting trapped air from under the rubber membrane when apply to the roof👍

[@Muzzle801]

You should come and show me on my roof I need to put down... 👀👀👀🤣

[@jasonknock2169]

Love the videos, they have helped me so much with information to my own current build.. i do have one question though what is the do's and donts with the pir insulation board? Should they have airgaps on the inside between them and the vapour barrier or can they go flush with the edge of the frame? I have a 4x2 frame on mine and want to install 100mm so it goes right to the edge... or should i go 75mm and leave the 25mm for an airgap Again great videos they are so helpful and informative

[@davidf1877]

First class video as always. Try ignore the ahole trolls!! Good to see the smile’s back after a tough time earlier in the year. One question - would you insulate the partition wall? Cheers

[@thegardenroomguru]

depends if we have any insulation left on the job mate, don't normally unless its a toilet

[@elliottreynolds]

Don’t normally comment, but I don’t like that people are trolling your generosity to help others. You don’t need to make KZbin videos, you do it to inspire people to push themselves, so thank you for that. You have inspired me to no end and I have just bought a new house purposely with enough space for me to have a go at building a garden room for myself.

[@Muzzle801]

Make sure to join the Facebook support group if you haven't already 👍

[@alankane8686]

Well said Elliott, been looking at these builds for the last 2 years or so, I tried to build a workshop for myself the last year but ended up with a Garden Room by watching these videos. I wanted to fill it with tools but it turned out so well my eldest daughter wants to move out into it. 🙄

[@ksm1985]

Seeing alot of videos of people putting the nail or screw through the edging AND the folded over rubber, as you say, makes no sense and over time water may get In

[@thedude7319]

Gotta respect the fact, you talk quite fast whilest working fast

[@adambrown6536]

What blade do you use in the multi tool to cut plastic

[@thegardenroomguru]

Just a fine toothed general blade mate

[@seanolaoire8476]

Great video.. watching from Ireland 🇮🇪

[@grahamhorwood9689]

Keep going Liam, bought build pack, watch all the videos, now halfway through my build. If people don’t like what you do that is their problem. I find this invaluable in telling me what I should be doing at each stage.

[@oliversimpson4994]

Ignore the trolls! Great video - Informative & funny, thank you for sharing! No doubt here on the quality of your work - Clearly a professional who knows what they're doing.

[@laapulsford]

These videos are packed with really useful information. Thank you for outstanding content.

[@paulcathcart9806]

Another cracking video and ignore jealous trolls. I will be using your guidance for my garden build. Great team mate... Well done to you all. Inspiring. x

[@garys628]

Jen. pleez pleez pleez wear knee protection of some sort. was in printing trade and hands and knees have suffered in later years......also hearing

[@Dodgy1]

To all the Trolls out there, Get back under Your Rock or is it Bridge, You are not wanted nor needed.. Cracking show as always gang, Keep er lit

[@nickdemetriades335]

I can never stop watching your videos Liam. You and team are relentless with your information. As for the trolls mate F@@@ them. Keep it loud and proud!!! 💪

[@therealdojj]

1, get them knee pads Jen, if only to stop you getting a splinter 2, ignore the fat comments Liam, it was a joke when it was COVID weight to show joist deflection but now it's a bit old 3, I was waiting for the cat cable info, maybe next time eh 👍 4, carry on talking, as you say, it's not a silent movie 5, look forward to the next episode 👍👍👍👍

[@benhill7904]

Shame you have to address those comments. You’re not fat my mate!

[@PaulBenthamcom]

Absolutely fantastic videos, I'm so glad you talk through every step. Genuinely one of the best tutorials I've seen on these types of builds. Thanks.

[@jshah7724]

Great job. If you do raffle a garden room how far will you travel ( North London)

[@admodz3292]

Liam fat..... people these days are just keyboard warriors or idiots. If you think Liam is fat... you should see my belly lol. Bet they don't have the bottle to say it Liam's face.... just block them and let them troll somewhere else .looking good Liam. Now get that garden room finished lol

[@ALG1K]

I normally don’t comment but I have to say your videos are bang on and I watch them all 👍 Ps jens a babe 😎

[@BPPavingnottingham]

If you need any patios to go infront of those amazing buildings let us know 👊🏼😊

[@arronconnah6669]

Thank you Liam for the time and effort you and your team put in to making your videos your step by step guide really does help keep it up F**k all you haters out there.

[@mburton5365]

Keep doing what you are doing mate, sod the trolls. If we did not like your videos then we would not be here watching them.

[@norvern479]

Ignore the troll's, they feed on getting a rise out of folk. I watched all your 1man, minimum tools series on holiday and now feel informed enough to build my own outbuilding. I'll buy one of your build packs and adapt to the size I need. 12.5m x 2.5m Big project, so I think I'll invest in a Paslode 😃 Now I'm going through the rest of your videos to pick up some more knowledge on self build. Thanks for doing the videos.

[@ianstanford4147]

Please don’t think we are all Trolls as I love what you do. People just have to comment as they feel like they are important twats. It’s easy to rip people apart and cause distress with stupid comments. They are just oxygen stealers in my opinion. Keep doing what your doing mate as we all love it. So educational and inspires me to attempt all sorts of projects that I normally wouldn’t without you kindly sharing all your hard earned knowledge with us. Keep it up Liam.

[@johnbosworth3663]

Great video as always. I'm right at this point with my build so super helpful. Ignore the jealous muppets.

[@jonunwin2780]

Dude, amazing no bullshit videos. They are extremely useful so ignore the negative dickheads that only serve to troll. I for one find you informative and very appreciative for the time you take to explain what you do. I want to build a 6x4 room with bathroom but Middlesbrough is too far for you so these videos are really helpful. Thanks you for your time.

[@NickFabi]

Great posting Liam, really helped me with planning my own project which is going to be insulated but was giving me a right headache as to exactly how to do it to avoid condensation as have seen too many other posts which claim all sorts of things

[@nekomatic]

Can you guys show how you do wall corners when two metal sheets meet? Do you use metal trims? And thanks for all the great info! I'm working on my build solo - your 'solo build with minimal tools' videos helped me a lot so far!

[@neilmckie2768]

Loving your stuff, which I've just discovered. The narrative is informative and witty, so thank you.

[@brianlochrie3958]

Another quality video. Liam n team. Don't pay attention to the muppets out there with negative comments not worth mentioning them. Keep the vids coming. Cheers

[@jamesirving-k7j]

Love the video, so helpful. Where do you buy the EPMD and fascia, cheers

[@malcelwell7209]

To be fare laim I think your a great boss and fare . You get respect because you work harder that all your employees and expect the same 👍💪

[@dannymorgan8509]

First time I've watched this channel and I've watched 3hrs worth straight off the bat. Don't listen to the haters they're just jealous dickheads. I think you and your team are amazing. Keep going these are great.

[@mariafhp]

Please don’t let people worry you . Thank you for the informative videos . We appreciate you . I’m doing a self build garden shed and the stuff you’re explaining is invaluable . 🤗💯

[@damianclarkson]

Cracking vid as usual, super helpful and well explained at every little step.

[@jack_irl]

its clear you're a professional outfit, dont worry about the idiots commenting on the internet.

[@ryantcb]

Embrace the trolls. Cos all views and comments count in the grand scheme of the KZbin algorithm to help grow your channel. 👏👏👏👏

[@hedfuka8608]

Liam may I ask what brand adhesive are you using...I see some require that both surfaces get glued,which would be a real pain in the arse. Watching from Ireland..👍..step by step..pure gold, thanx.

[@thegardenroomguru]

hi, its just Firestone or unbranded water based mate, gluing both surfaces would be a nightmare, especially this time of year

[@hedfuka8608]

@@thegardenroomguru Thanks for getting back to me..👍

[@xdiehardx-psn4176]

You have to glue the decking and the rubber roid otherwise it won't stick and will bubble up especially when it's hot. You should also blowtorch the glue especially in cold weather so the glue is sticky and not wet when you lay the rubber

[@johnp6636]

Ignore the idiots you do an amazing job

[@CORRIGEEN71]

Their should be champering pieces on the sides to keep water run off in one area

[@stewala3069]

Yer don’t need to explain yerself Liam just carry on doin wot yer doin lad 👊🏻👏🏻👏🏻👏🏻👏🏻

[@craigbaxter4842]

How on earth do these muppets think you can explain what you are doing without commentary????

[@thegardenroomguru]

I’ve no idea, tbh, I just don’t get people like that, if you don’t like, don’t watch, surely it’s that simple

[@alansadler1]

Love your videos Liam, im in middle of my build and like this one ive got a store room, do you insulate outside walls? the store room dividing wall? or both? I was just going to insulate the dividing wall and leave the out side wall of the store room but not sure if that's correct. Cheers couldn't have got as far as i have without your videos. 👍

[@thegardenroomguru]

we insulate all external walls mate incase customer has a rethink and wants to do away with store room, its happened before to us, floor and ceiling too, if theres insulation left we may do the internal

[@seanocarolan359]

Good job! I've learnt a lot and you describe things very well. Never mind the A-holes!

[@Beastmode23ua]

Honestly watching your videos are soo relaxing 😅

[@thomascoyne157]

Nice one Liam and all the lad’s and Girl , and remember trolls for ignoring and not given them air time sad people . 👍👍👍👍👍🇬🇧

[@matthewkabat4633]

Good day to Liam and then team keep posting videos

[@trevorquigley3146]

Haters will hate .I think the videos are great love watching them keep up the good work I'm watching the van video as well 👍

[@robynstewart8312]

Great stuff liam keep it up take no notice of idiots that don’t have a clue 👍👍

[@JohnHavord]

Keep talking Liam :)

[@constantinelykiard1644]

You have a great team... your approach is based on solid experience and you apply it with skill. One personal hate ... nothing to do with you... its how the roofing trims make al these jobs look kind of cheap. It would be good if the visible elevations at least, had a continuous floating piece running across the elation masking all the plastic cover joints and nails ... anyway top draw all round

[@nyqer6636]

As I am just catching these , could you do a "part one, two etc " sequence title?? Make it easier to follow , Cheers. Love the vids btw.

[@TheStudio49]

If you polish the inside of the glass with a small amount of fairy liquid it shouldn't steam up works great on motorbike helmets 👍

[@leewright5952]

did you get any apples from next door for a pie ?

[@ianwarren7432]

I would just like to say to Liam and team a big thankyou for the clear and concise content quality of your videos. You make it easy to follow and understand and keep it light hearted and entertaining. You will always get keyboard warriors looking to undermine you and treat their comments with the contempt that they deserve. Keep up the good work and continue with these brilliant step by step videos, I look forward to seeing future projects. A word of caution for your prettiest member of the team, Jen please consider wearing knee pads, as a former carpet fitter, I to neglected to wear them and now live in constant pain especially in the winter. I would hate to see you suffer as I have later on in your life.

[@therealdojj]

I wonder what the Amazon buy could be...🤔

[@iqqeiqqe7405]

amazing job . hi its iqbal . thank u very much . i got plenty of help from ur video . i think u r a good joiner . well done .man

[@hehe3439]

Proper job pal I know what it’s like these so called keyboard Warriors😂😂😂

[@mariafhp]

Thank you Liam for the great 👍 informative videos . I’m self building my 8x8 shed , would like to know what brand of rubber roofing you recommend as thought you mentioned company but couldn’t get it . I’ve got to get it ASAP as sheet materials coming Friday . Cheers Liam 🤗👍

[@alankane8686]

Hi Liam and team, I have one question if you could let me know what you think. I've just completed one of these builds that I built all by myself using a very large amount of your ideas. I really wanted a Edpm rubber roof because I loved the look of the black finish but I've noticed a slip issue with it. Some days when I look out over the roof on hots days there are a few strips of rubber that lifts away from the plywood so I get a couple of long bubbles. If I put the down the do stick back down but lift again. I wondering if this has happened you before on any of your builds and if so is there an easy fix without recovering the whole roof again or worst case trying to tak it off and stick it back down and me more liberal with the glue. Alan

[@stevewhite8820]

Hi I don't comment on your videos normally . I think you do a fantastic job making these videos. I am all for positive thinking. I wouldn't give any air time to those sad bast**ds that like to have a go at people that are hard working to make a living. We all go through testing times in our lives. I haven't lost a parent yet but sadly lost my wife a while ago, grief is awful to go through but I am sure you will learn to live with. Let them live in someone's else's head mate. Keep up the good work, that you and your team are doing. Really enjoying the campavan videos too.

[@zenmaster6264]

Bicycle repair glue…….only og’s know this……!🤣🤣🤣

[@thegardenroomguru]

😭

[@brentsmith5647]

Watching and learning thank you very much👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@dereklawson945]

Brill… takes me back. I did this last summer on my garden room, and worked a treat. Jewson sent ply instead of osb for the roof…their cost!… and I did this on a warm sunny day. The rubber was easier to work when warm with and I did not apply contact adhesive. I agree.. apply liberally push out the air bubbles and tie in the overlaps onto the facia. Neat, tidy and waterproof.

[@supareelsmusic9415]

AT 72 AND SPENT MY CHILD/TEENAGE YEARS HELPING MY OLD DAD ( HE WAS A FENCER ) SEE YOU CUT THROUGH THE B/S AND DOING THE JOB IS LIKE A BREATH OF FRESH AIR ... BRINGS THOSE DAYS OF DIGGING ROCK HARD MUD ON BUILDING SITES FOR POSTS AS QUICK AS POSSIBLE DUE TO DAD WAS ON PIECE WORK BACK ... AND BOY DID I SLEEP WELL IN THOSE DAYS ! .. THANKS FOR THE LITTLE DETAILS YOU POUR OUT AS YOUR WORKING .. NOT LOST ON ME

[@frankblack1481]

The good news: the £20 mask stopped the Paslode nail. The bad news: The dog in next door’s back garden was later found with two ring-shank nails buried in its side.

[@marknadin770]

Great vids Liam, keep talking that simple task of talk or not could help someone that didn't use speed square as straight edge for cutting.👍👍🍺🍺

[@StingaleProperLike]

The fact people question you about your team and way of work is a joke. Top team and great Videos thank you 🤘

[@matthewharmer1656]

Great video , how much would it cost to build a roof like this??? Cheers.

[@solawoodart9609]

Why don't you use a "california corner" while still doing the walls? There are many advantages.

[@thegardenroomguru]

that's practically what we've done, except ours uses less timber and is easier to insulate

[@solawoodart9609]

@@thegardenroomguru 😃 4 pices less ???? This is a joke right?🤡

[@thegardenroomguru]

Nope, offcuts are for using not skipping 😎

[@solawoodart9609]

@@thegardenroomguru OK understand👍

[@markarmstrong2592]

KEEP TALKING lol

[@leakybean501]

Liam, take no notice of the idiots. Great content, thanks for sharing👍👍👍👍

[@Leonard_Smith]

Good video on every level people 👍

[@shanzeumar9280]

Very useful information.Can you show us how to install air vent on the side .

[@BD-if6uu]

Great videos Man!

[@bigboundsy]

Not trolling at all, but I’ve always left the air gap at the top so the insulation sits flush with the rafters? Also do you guys solely do garden rooms?? How do you generate work? I get about one or 2 a year!! Great work guys 💪🏻

[@thegardenroomguru]

We just do garden rooms mate, we get all our work from social media, never had to pay for advertising as of yet, however it has slowed down massively, cost of living crisis etc. I’d imagine we could gain more work if we advertised but you can’t get the trades tbh

[@aaronthew6134]

RJ45 ;) not G :)

[@thainigthu]

Ignore the fuckers and arseholes, great videos! 👍

[@brentsmith5647]

A job well done👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

[@nickgriffin637]

Love the silent movies speech at the end 😁. Great video

[@moftyinmeysey]

Great work guys. Just a note of observation with those masks... when i was a biker i used to get the same trouble with the visor misting up. the trick i had was to just smear some washing up liquid (not too much) over the inside surface and the fogging vanished. hope that helps.

[@thegardenroomguru]

I’ll try this, thanks

[@mrsandman1416]

You should be on the BBC on some kind of building show.

[@thegardenroomguru]

🫣🤣

[@shanesloan3859]

Great vids 👍👍always good work 👍

[@brento4148]

Liam and the team. I've just finished my build and 80% of the knowlege came from watching hours and hours of your content in preparation. There's a lot of information on the internet and youtube, in depth stuff that should be taken into account, but honestly, your no nonsense approach and instruction made it possible for me to slap a building together with basic tools and it's a high quality, solid building that we'll enjoy for decades. Thank you.

[@turnbull321]

This is great, thanks for sharing

[@petecroxford3277]

🇬🇧👏👍🇬🇧👍🇬🇧🍺🍺🍺⭐️⭐️👏👏👏

[@chrisillingworth7967]

fantastic tip with the speed square

[@adzhx]

What happened to Adam who used to do the electrics ?

[@thegardenroomguru]

He left

[@ALG1K]

Ps Jen needs some knee pads

[@thegardenroomguru]

You tell her, she don’t listen

[@johnp6636]

Did you not watch the video he explained about knee pads

[@1jimmydodger]

Ive watched a load of your vids and they're great just one suggestion it may be easier to put the 250mm screws in with a drill instead of a impact driver

[@thegardenroomguru]

impact driver is made for the 250's, johns Milwaukee can't be beat, by anything

[@1jimmydodger]

@@thegardenroomguru fair enough mate