General Electric Washing Machine Not Filling With Water - The Water Valve Filters

General Electric Washing Machine Not Filling With Water - The Water Valve Filters
Replacement parts amzn.to/49abuIz - paypal.me/Angeltheapplianceman
Warning: Use the information in this video at your own risk

[@anthonygallegos5826]

Nice video and thanks for showing both types of filters

[@kcorbiekeli4816]

Thank You !!!! great job !

[@brucesteel3054]

Where do you buy the white type of water filter i damaged mine when removing

[@RM-np1gm]

What about "Partial fill"? CHECK and Clean water inlet screens! Many vids and website hits on fill issues. My issue was partial fill vs over fill or no fill. Like most I replaced the water level pressure switch but problem persisted. I did remove (in pieces cause it was old and brittle) the screens in the water inlet valve assembly. Filters were plugged. What no one mentions that I saw, is the water pressure valve does NOT control the water level, it's kind of a safety. Water needs to fill at least partially to close the low switch in the pressure valve and the high is to prevent an overflow. Low side makes and lets machine know that it can now run, high side stops the machine. The volume of water determines the level and is controlled via a timer (in a control board possibly). I replaced the inlet filter screens, set the level to 'Super' (max) and all's good. It takes 6 minutes to fill at house water pressure of 65 psi.

[@soapmom426]

Mine was the control board malfunctioning that was causing it to partial fill.

[@sherluck271]

Can I just take the filter and the plastic things out?

[@TheMajinvegetadbz]

No. It'll mess up the pump/valve. That's why there's filters

[@soapmom426]

I did and the rubber filters expanded and would not go back in.

[@sherluck271]

What I did was take the hoses off the back of the washer there was build up like brown mineral dirt. I took my re chsrgabe blower to blow the junk out uses a paper Towel to wipe it out it worked! My washer fills up now. So check the hoses see what's clogging it. Mine was brown good I have a well so I'd say it was hard water build up.

[@itsthemuscledad38]

You didn't show how to clean it

[@itsthemuscledad38]

Anyways, Thank you for showing how to remove the filters !!!

[@Kris6535]

How bout some soap and water?🤣

[@soapmom426]

If you take the screen out with the rubber seal they do NOT POP IN LIKE HE DID. THEY DO NOT GO BACK IN.THEY ARE NOT MADE TO BE PULLED OUT. IT LOOKS LIKE THEY WOULD AND I THOUGHT THIS WAS EASY PEASY UNTIL I HAD TO PUT THAT SEAL BACK IN..IT WILL NOT GO IN. IF YOU NOTICE…HIS WASHER MUST HAVE SAT FOR A VERY LONG TIME OR ITS A JUNK WASHER HE MADE THIS VIDEO WITH. HIS INLET VALVES AND SCREENS ARE BONE DRY. THE SEAL HAS SHRUNK. ITS BONE DRY. MINE WAS NOT BECAUSE I USE MY WASHER. HE DID NOT SHOW HOW TO CLEAN IT BECAUSE IF HE DID HE COULD NOT HAVE GOT HIS BACK IN…HIS WENT IN EASY PEASY BECAUSE HIS WAS BONE DRY. I HAD TO BUY A SEAL TO GO IN THE HOSE ITSELF BECAUSE YOU CANT GET THOSE BACK IN. You have to buy the whole valve system with the screens already in if you take those out. It was a nightmare attempting to get those seals back in. HEAR ME ON THIS..THEY EXPAND ONCE YOU PULL THEM OUT and you can’t hammer them in if you wanted to!The 1/2 inch socket wrench is a fricken joke. This is a junk video! I NOW have to go buy seals to go in my hoses. Cant buy new valves to go back in like those.Those are sold ALREADY IN THE INLET UNITS BECAUSE,ONCE AGAIN,THEY ARE NOT MADE TO COME OUT! THESE WERE MADE SO YOU HAVE TO BUY A NEW INLET UNIT OR CALL A REPAIRMEN TO REPLACE THE WHOLE VALVE UNIT! BEWARE!

[@soapmom426]

I explain above WHY HE DIDNT TELL YOU HOW TO CLEAN IT. PLEASE READ.THIS IS A SCAM VIDEO. PARTS STORE SHOWED ME WHY IT DIDNT WORK. THEY WERE NOT TRYING TO MAKE A DIME OFF ME EITHER. THEY GAVE ME THE SEALS TO GO IN THE HOSE WHEN THEY COULD HAVE SOLD ME NEW VALVES ALTOGETHER LIKE OTHER APPLIANCE STORES TRIED TO.READ BELOW.

[@soapmom426]

@@Kris6535 DONT TAKE THE FILTERS OUT…READ ABOVE WHY!