Thanks man youre awesome the GC community appreciates your work
@justinallen57292 жыл бұрын
Thanks for the good Genesis Coupe content brother.Keep it up!!
@brandongates22192 жыл бұрын
Just followed your video and my car runs now ...awesome content
@seoufulracingsfr63232 жыл бұрын
Good video, honestly this is way more simpler then what I do.
@HandMadeRoyalty2 жыл бұрын
Do you pull the oil pump too?
@Jacob-rt6on2 жыл бұрын
3:00 "this pulleys just gonna fin spreely" lol
@mannyfenix22882 жыл бұрын
genesis coupe master back at it with another useful video for us scrubs.
@MarkissLovesU2 жыл бұрын
Your are elite bro. I appreciate you making this video. It’s definitely informative
@senpaihouston2 жыл бұрын
Your explanation was perfect thanks!
@sk8erboy5512 жыл бұрын
Amazing content as always!
@yyzervy2 ай бұрын
how did you get the crank pulley off. i got the bolt but holy that pulley is holding on for dear life
@ProdigePerformance2 ай бұрын
@@yyzervy you just pull it straight out. I’ve never had a crank pulley give me a hard time on these cars
@ajvprКүн бұрын
Im experiencing the same myself. Everything else in the process has been smooth. I put some penetrating spray and trying again in a few hours.
@ProdigePerformance13 сағат бұрын
@@ajvpr should be able to pull straight out, if not you can easily just use a pry bar
@MJT-DA2 жыл бұрын
I'm TDAM from reddit this helped me so much! I subbed right away you literally saved me $1500 from the stealerships. Also did you ever drain the coolant? I never saw you do it other than removing the hose and saying not to open the cap at all or you'd let air into the system.
@johnsullivan937 Жыл бұрын
There's no need to remove the coolant as long as you keep the radiator cap on. The system will be pressurized and hold it all in even though that little hose was taken off. I do the coolant bypass for every summer since it gets so hot where I live, you have to take off a little hose in almost the same spot. It just drips out a little bit of coolant, and stops after a second.
@allensarraf41842 жыл бұрын
Brooo wheres part two?? Love your content
@ProdigePerformance2 жыл бұрын
Coming out today
@allensarraf41842 жыл бұрын
Brooo stop playin 😂
@ProdigePerformance2 жыл бұрын
@@allensarraf4184 ok ok check now lol. Turns out that video never got uploaded because of copyright strike on the music I used. But I re uploaded it just now
@palfreyPodcast2 жыл бұрын
great content and camera work.
@AphexHaw3k2 жыл бұрын
This is so helpful. There aren’t videos out there showing how to do the timing chain in a genesis coupe. How much does a job like this cost for the customer. I don’t have many tools or time to do this entire job myself on my 2.0T. What’s an total estimate cost?
@ProdigePerformance2 жыл бұрын
Shops charge $900-$1200 for labor not including parts.
@dkennedy95246 ай бұрын
Was this just preventative maintenance or did it jump time or stretch? Im looking at getting one but they say it needs a chain, was wondering if it would be worth getting to just try a chain and tensioner and guides
@ProdigePerformance6 ай бұрын
Bk1 timing chains stretch by 80-100k miles so it’s recommended to replace with a bk2 timing chain since it’s stronger and will last longer. Bk2 timing chains typically last another 30-40k miles before they fully stretch You’re supposed to periodically check when you do the valve cover gasket after every 45k miles
@dkennedy95246 ай бұрын
@ProdigePerformance I really appreciate it. They said it doesn't run needs chain, it looks in pretty decent shape and they are askin 1500. You think it would be worth getting and hoping it's just stretched?
@ProdigePerformance6 ай бұрын
@@dkennedy9524 if it doesn’t run I would try to figure out why A stretcher timing chain doesn’t cause the engine to not run so there’s another issue
@delicrux2 ай бұрын
@@ProdigePerformanceglad someone asked this I have a bk1 and I had it scheduled for a trimming chain replacement. The week before the appointment I drove my car to work parked it and couldn't start it when I got out of work. Code was for camshaft position and after taking the cover off recently ican see it's stretched. Had it towed to a shop and the sleazeball said the valves were bent without doing any diag and said it will cost a new engine at 6k plus labor or he would buy the car from me for $100. Btw he builds racecars and sells used cars on his lot... So I had it towed home where going to do a chain replacement today.
@othyus78962 жыл бұрын
At 11:35 you point out the buildup on the side of the engine and recommend cleaning it off. What’s the best way to do that? Just wipe it with a rag? Also, I’ve heard that you should change the cvvts when you change the timing chain is that good advise?
@ProdigePerformance2 жыл бұрын
Lint free rag and use wd40 and wipe away And yes it would be best to replace both cvvt actuators / phasers in the process
@othyus78962 жыл бұрын
@@ProdigePerformance Could you point me in the right direction of what exactly I need to buy and how to swap it? I’ve looked around online and can’t seem to find what you’re talking about. There’s sprockets and solenoids but that’s all that comes up.
@ProdigePerformance2 жыл бұрын
@@othyus7896 cvvt = cam phasers. It’s built into the phasers
@spaace9414 Жыл бұрын
10:25 never knew it was a two in one. but there is another sensor on the driver side under throttle body just saying u might have missed that one
@ProdigePerformance Жыл бұрын
That’s oil temp related. Not timing.
@ProdigePerformance Жыл бұрын
Or are you referring to the one on the intercooler piping? If so, no that’s not a map sensor. It’s a TIP sensor.
@spaace9414 Жыл бұрын
@@ProdigePerformance I seee
@juniormadrid93402 жыл бұрын
When would a timing chain job be recommended? By how many miles orr? And the best one to replace it with is oem or is there a better after market one??
@ProdigePerformance2 жыл бұрын
No aftermarket. The best timing chain you can get is the bk2 timing chain. Way more durable And I usually say check it. Around the 100k 120k mile mark is when I recommended 2.0 owners to replace it
@chevyschroeder47942 жыл бұрын
And what if you have a automatic/manual what does that mean about holding the crank into place.? What is the procedure for that?
@ProdigePerformance2 жыл бұрын
6 speed guys can simply Put the trans in 6 gear and remove the crank pulley bolt but auto guys would have to use vice grips to prevent the engine from spinning when removing the crank bolt.
@chevyschroeder47942 жыл бұрын
Is it ok to remove everything and drain the oil two days before parts arrive?
@ProdigePerformance2 жыл бұрын
Just make sure if you leave the Valve cover open to put a plastic bag to prevent debris From contaminating the engine
@JuanSilva-nl3sv Жыл бұрын
You don’t gotta make sure to have at top dead center??
@ProdigePerformance Жыл бұрын
In the next video I talk about it. This is just basically removal.
@phenomphantom53292 жыл бұрын
I’m learning more about my car with Brian Paul I have a 2.0t 2013 Gen coupe I want to install a down pipe but I’m scared I’m going to break a bolt 😞
@bk2_sadie368 Жыл бұрын
Do it. If it goes wrong tow it to a shop
@calvinunroe24622 жыл бұрын
When is part 2 coming out
@ProdigePerformance2 жыл бұрын
It already did
@calvinunroe24622 жыл бұрын
@@ProdigePerformance sorry man you right just found it
@ProdigePerformance2 жыл бұрын
@@calvinunroe2462 you’re good
@christianvasquez1797Ай бұрын
Crankshaft sensor easy to replace?
@ProdigePerformanceАй бұрын
@@christianvasquez1797 yep: under intake manifold not hard to get to really. 10mm bolt. They usually never go bad btw.
@christianvasquez1797Ай бұрын
@@ProdigePerformance I just did a rebuild on my engine and it’s throwing p0017. Just wanted to confirm my man Appreciate you 🫡
@ProdigePerformanceАй бұрын
@@christianvasquez1797 lmk if you have any more questions
@ericjay12043 ай бұрын
What state are you in
@ProdigePerformance3 ай бұрын
@@ericjay1204 Texas
@HandMadeRoyalty2 жыл бұрын
Do i have to drain the oil to do this?
@ProdigePerformance2 жыл бұрын
Yep
@HandMadeRoyalty2 жыл бұрын
@@ProdigePerformance one last thing, did you change the cam sprockets as well? Before or after this video.
@ProdigePerformance2 жыл бұрын
@@HandMadeRoyalty no, but I recommend it
@HandMadeRoyalty2 жыл бұрын
@@ProdigePerformance is their a reason you did not order the sprockets?
@ProdigePerformance2 жыл бұрын
@@HandMadeRoyalty it’s not my engine. It’s a customer lol. All these videos I make are from customers cars besides my genesis which was sold in February. I have a c5 build going on right now