In this video we show you how-to program your Genie Wireless Keypad to Genie Intellicode garage door openers. This model GK-R wireless keypad is compatible with All Genie Intellicode openers manufactured since 1995.
Пікірлер: 312
@SHEPtheBISH3 жыл бұрын
For anyone painfully stuck here, it doesnt mention it in this video or in the manual but you can only take these reset and reprogram steps if the garage door is CLOSED.
@shanetaylor89582 жыл бұрын
It does too
@knowledgeseeker312 жыл бұрын
Yes… this is true. Thank you. It was opening on the first number of the PIN until I programmed with door closed. 👍🏼
@jdub67302 жыл бұрын
Thank you so much. After literally hours of trying and frustration all I needed to do was shut the damn door. Thank you.
@timdickey9182 жыл бұрын
Thank-you! I couldn't figure why I could not get the codes to work, closed door, worked on the first try.
@KGTv1232 жыл бұрын
Lol wow. Thank you for that. I thought I got a bogus unit
@eustaquiodurazo710218 күн бұрын
Thank you so very much Sir.If you only knew how helpful your video was.it's almost 10pm right now in Redlands ca.i misplaced my remote and have not used my keypad for close to a year.Thanks for good instructions.GB
@abbasiowais22 жыл бұрын
Just fixed my garage few hours ago while watching this videos. Worked for me
@DaveSeefeld2 жыл бұрын
Thank you so much! This video helped me out after hours of frustration. Three part about factory resetting the device first was what helped me most.
@zipmac22 Жыл бұрын
Great video! I had ordered both the Genie Wireless Keypad and Genie Wall Console. The wall console directions were pretty straight forward, but the wireless keypad directions were a lot more fuzzy. The video cut through all that fuzziness and just gave the brass tacks and left out all the fluff from the written directions. It also helps watching the video being a visual learner. Thanks for taking the frustration out of it!
@juliandavis6551 Жыл бұрын
We finally got this thing to operate properly. My wife, who is much smarter than I, got it done.
@MegaLdawg3 жыл бұрын
The manuals I found online and on Genie's website didn't work. What was a simple task turned into a nightmare. Thankfully I found this video and it was spot on about resetting the factory pin/re-programming!
@stevenking93572 жыл бұрын
I hate Genie now. I've had nothing but problems with my remotes and keypad.
@jennifertab46094 жыл бұрын
I have been trying to do this for months and it finally worked using your video! Thank you!!!
@davidcasler89133 жыл бұрын
Thank you, this works. Much better than trying to read the manual!
@pattien71132 жыл бұрын
Thanks for this. Able to program and replace my old keypad on the first try!
@pattivioli90693 ай бұрын
Great video. I had tried before using the written instructions. They were very confusing. Your video made this a ten minute task !
@ohnurse76903 жыл бұрын
Worked like a charm! Video was very informative. Thank you.
@SaltWaterRiders5 жыл бұрын
Honestly one of the best videos out here on genie door opener’s
@korbrexo2 жыл бұрын
Thank you! I was so frustrated trying this before watching your video, especially just knowing the garage should be closed before attempting!
@kingalex-xw7kv2 жыл бұрын
I did it while it’s op nd
@ericavance45342 жыл бұрын
I missed that part! Thanks for this comment!!!
@JourneyKat753 жыл бұрын
Thank you so much for this video! It was easy to follow and most importantly, IT WORKED!!!!
@GenieCompany3 жыл бұрын
you're welcome!
@triciaedling37303 жыл бұрын
Great video 👍 Thanks!
@zsalgado812 жыл бұрын
Thank you easy video. I have tried so many times to program but this really made it easy.
@DJ-uj6mk2 жыл бұрын
Thank you so much. Thought I was going to have to throw mine out because the instructions that came with it were not as helpful as your video. Great video. Saving it for future reference.
@franklago2548 Жыл бұрын
Great video, informative and easy to follow.
@jeffu32482 жыл бұрын
Life Saver. Worked flawlessly
@waynemiller60702 жыл бұрын
And for those unclear about this: when you add doors 2 and/or 3, the first door automatically becomes number 1. In that if you have multiple doors, you need to hit your code, the up/down button and then 1, to open or close door number 1.
@daleunroe60748 ай бұрын
thx ...that wasn't clear in the video - in fact the guy said to either click number 2 or 3 ...which had me curious about door 1
@donjernigan34354 жыл бұрын
One step is missing if you have an older opener. The LED needs to be red (shown when you press a button) to work with all openers. To switch from green to red, enter the passcode (default is 3, 5, 7, arrow key). Then hold the PROGRAM button until the LED switches from green to red. Excellent video!
@robwienburg39883 жыл бұрын
Lifesaver! I almost turfed this thing until I read your comment. LOL red mode, FTW =)
@jonathankotz58092 жыл бұрын
Man I would buy you a beer if I could!
@Flawed2Flawlezz3 жыл бұрын
This video was extremely helpful, thanks
@TrevorMoody Жыл бұрын
Absolute lifesaver, this video!!🙏🏼🙏🏼 God bless you!!
@Red_Rover5 жыл бұрын
Finally!!! Found a method that works. Thank you!!
@MrFehmin2 жыл бұрын
Works and looks great doing it
@GLockman47117 ай бұрын
Directions worked perfectly.
@billavara5 жыл бұрын
Thank you for this video. I keep coming back to it every time
@estherrodriquez68373 жыл бұрын
This worked thank you 🙏
@tcwriterdave558911 ай бұрын
Super helpful. Thank you!
@maureenw-brown26053 жыл бұрын
This was a very very helpful video. It was spot on! Your video actually saved me and helps me to have my remote pad programmed when I couldn’t use it for over 2 1/2 years. Thank you so much for your detailed video it was a lifesaver!
@adeny7842 жыл бұрын
Very helpful and explained well
@freeconfederate Жыл бұрын
Great video! But I think one small step is assumed. On a new unit you use the factory code and program key to set your new PIN. And that works without using the program button on the main power unit. Addition PIN changes will require that the PROGRAM button on the main power unit be activated before a PIN change.
@PeaceDayCortez Жыл бұрын
Can you clarify? I had to factory reset after I changed my wifi provider. My master lift is programmed but I still can’t get the key pad to link up. I followed this video but it still not working, I’m thinking perhaps I’m missing something.
@melg56635 жыл бұрын
Thank you Sir!!! Perfectly paced video! It took a few resets but it all worked. I liked and subscribed
@GenieCompany4 жыл бұрын
You're welcome, and thank you!
@juliandavis6551 Жыл бұрын
Good luck reaching Genie Tech Support by phone. Hold time was two hours. They did offer a call back option which I used. The call came early while I was working outside. Not Genie's fault but nonetheless frustrating. Now, I'll try the video.
@greggoldman97395 жыл бұрын
Great video!!! Detailed and simple. Used this instead of the paper instructions.
@craigb99992 жыл бұрын
As mentioned, the doors must be closed to program. I also found it helpful to do this in low light conditions, or you won't be able to properly see the keypad. Have a ladder on hand to be able to reach the programming button on the opener.
@stevenking93572 жыл бұрын
So you're saying I have to unmount my keypad to reprogram? How silly of Genie.
@Herrick1955 Жыл бұрын
@@stevenking9357 Thank you so much I did not know that IT HAD TO BE CLOSED! BIG HELP!!!!!
@spawnmonkey2 жыл бұрын
Thank you. Very helpful.
@jamal31212 жыл бұрын
Awesome vid made it easy.
@TheBulls9353 жыл бұрын
Great video! Covered everything in a short amount of time.
@bark12912 жыл бұрын
It worked amazing way so much better than having to read those stupid instructions that comes in the box thank you so much
@nateschaffer54564 жыл бұрын
Thank you!!!
@JagtarSingh-ey9wi3 жыл бұрын
Simple and clear instructions!! Thank you!
@joem13yearsago732 жыл бұрын
You're welcome Jagtar
@mikeamerica43014 жыл бұрын
Saved my azz thank you!
@jeffsmithsmuzik59933 жыл бұрын
The manual leaves out so much of this important proprietary information. Thanks for making a video with the actual instructions.
@kenneeds5 жыл бұрын
I mounted one of these on my metal trim around my door, and it would not work. Found I had to move it off of the metal for it to work.
@johnzarbus886 Жыл бұрын
My keypad has worked I want door successfully for the last year. I added a new genie opener to the second door last week. Just follow the steps in this video so that I could use the same keypad to operate both doors. However, when I put in my pin both doors simultaneously go up or down. Is this supposed to happen or is there a way to do just one or the other door
@kakashibigd4947 Жыл бұрын
If nothing is working for anyone. Make sure your opener is not locked. Took my hours to realize but there was a lock option on the wired opener on my wall and it was set to lock
@stayslidewayz4 жыл бұрын
thanks this helped!!!
@barbaral.vaneck24934 жыл бұрын
Thank you!
@robertkarz4380 Жыл бұрын
Good video... much better than manual! If your keypad stopped working (like mine did) and the batteries are OK, try taking it apart and cleaning the keypad and battery contacts. The unit is very well built as remotes go, and the problem is likely to be due to dirt or corrosion.
@techguy943 Жыл бұрын
I recently changed the batteries in my wireless keypad and the keypad will not open or close my garage door When I first placed new batteries in it when I pressed a button the backlight on the numbers flashed I gave the batteries a try again earlier before I came to this thread and the backlights lit up solid but I don’t think I was able to get the garage door to run so I didn’t enter my code to try it Maybe I need to let the batteries “charge” or something (I DO NOT MEAN ”CHARGE” like you charge your iPhone battery but I mean let the keypad warm up to the motherboard If that doesn’t work then I’ll check for dirt and corrosion UPDATE: my keypad STILL DOES NOT WORK I LITERALLY CHANGED THE 🔋🔋 ALMOST A MONTH AGO
@razakfashola3068 Жыл бұрын
Really helpful
@msvd103 жыл бұрын
Thank you! So much easier than the manual. Finally got it to change the code
@JediFight3 жыл бұрын
Thanks. Very helpful. Anyone giving a thumbs down can’t follow directions.
@tonybudetti2 жыл бұрын
Not true.
@JediFight2 жыл бұрын
@@tonybudetti it’s true
@winandwin66353 жыл бұрын
This video is very helpful compared to the manual
@noble19693 жыл бұрын
Got it! Make sure your program led has gone to red! If it is still green it won't reprogram!
@RJJackson093 жыл бұрын
Success! Now my keypad on my new house that’s been sitting there collecting dust for a year can be of use 🎉🎊
@Mreticket13 жыл бұрын
Thanks, this was very informative
@earlhenrysr15043 жыл бұрын
Very helpful 👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽👍🏽
@chemicalreaction77884 жыл бұрын
Success. Thank you
@1Pueblito4 жыл бұрын
Very easy, I wish I would have saw this video before trying it off of the keypad instructions.
@jeffthompson95894 жыл бұрын
Thank you SIR
@GenieCompany4 жыл бұрын
you are welcome!
@chicofun47794 жыл бұрын
Thanks for your video. I just bought the same keypad but my old Genie model 12A has a Dip switch, is there any way I can make it work with a key pad? It would be very convenient to have the keypad installed outside.
@GenieCompany4 жыл бұрын
The intellicode keypad is not compatible with the Genie dipswitch operators. Please reach out to us at 1-800-354-3643 so we can provide you more assistance.
@rsheldon863 жыл бұрын
I followed your steps to set up multiple openers, but every time I type in the pin and which number opener, both doors open at the same time. How is that possible?
@minhly38744 жыл бұрын
Thank you
@shanetaylor89582 жыл бұрын
What if I want to control two doors and I want to open door number one? You say to hit the pin, up, then 2 or 3. What if it’s the primary door I want to open? Also, you say current pin then say pin when talking about the second door. I thought the second door got a different pin, this screwed me up several times
@mouseypublishings2 жыл бұрын
Thank u, Tom Arnold.
@WileysShenanigans7 ай бұрын
Is it possible to disable a genie wireless keypad while still having the car remote operate the door?
@overallgreatidea6433 Жыл бұрын
I watched all the videos and tried all the tricks and resets. Nothing worked. Finally when I was just going to give up I decided to try once more. I opened the cover, the battery cover popped off, there was a hissing sound, and a tiny blue genie popped out of the remote and flipped me off
@MClover420 Жыл бұрын
😂🤣💀 Well the word Genie does originate from an ancient Arabic Demon called a Jinn or Ginn and it wasn’t something perceived as good until after Aladdin and His wonderful Lamp was written by Hanna Diyab in the eighteenth century
@overallgreatidea6433 Жыл бұрын
@@MClover420 Without the revisionism of making good evil and evil good, the working material of writers and activist historians would soon be depleted. lol
@Worlds1stClone75Ай бұрын
Will this keypad work with other brand door openers?
@jonesmrnable2 жыл бұрын
Everything seems to operate as directed except... when using the keypad or openers, instead of opening or closing my garage door, the motor box just clicks?? The wall mount button opens and closes it without any issues though.
@domcola74802 жыл бұрын
Why have you not addressed burrbro235 question. I have the same issue followed the instructions and in the end my pin opens both doors at the same time
@snoogcity2 жыл бұрын
Any tips on resetting the keypad ? Bought a house and they didn’t leave the code
@rafaelfuerte47979 ай бұрын
Does the default code open the garage? If so then mine isn't doing that
@anahicastaneda31272 жыл бұрын
Does anyone know how to make the keypad or the remotes close the garage door?
@thomasburrell71203 жыл бұрын
These instructions are great. It worked. The manual is not well written!
@13_islanderАй бұрын
This apply for old genie openers ?
@CarlosCastillo-rm3eh10 ай бұрын
do i need to have that specific keypad?
@Fightergator014 ай бұрын
What's the difference between the GK-R and GK-BX models?
@srinivas8444 жыл бұрын
Thanks
@bobb60939 ай бұрын
About the keypad reset procedure. Can someone maliciously do the keypad reset procedure resulting in erased codes and therefore unable to open the garage door(s)?
@lotts66493 жыл бұрын
Great video, and I have a question. When entering my PIN, the LED flashes for the first two digits, but not for the remaining. Is this an indication the keypad is broken or letting me know the PIN is not valid I'm hoping to know before attempting to reset the PIN using the learn mode. - Thank you!
@GenieCompany3 жыл бұрын
Every time you press a button the LED indicator should flash. If it is not flashing could be that the button isn't sensing the press, or possibly you may need a replacement.
@knowledgeseeker31 Жыл бұрын
I do acknowledge this is a clear & straightforward video. I spent the entire afternoon trying to program the second door. Simply didn’t work 🤷♀️
@duckpond-studio Жыл бұрын
what do you enter if only operating 1 door?
@bkilpatr1003 жыл бұрын
I don't like having to enter in the pin number to close the door. Is there another way? Previously I had a Liftmaster keypad, and to close the door all you had to do was press the enter button. Of course, you had to enter in the pin + enter to open it.
@danzgarage8433 жыл бұрын
Im looking for the same thing
@MikeyBats5 жыл бұрын
This video helped a lot..thanks Genie
@GenieCompany5 жыл бұрын
You are welcome
@tonysarmiento46295 жыл бұрын
@@GenieCompany need help I hit any button and it goes up and down
@GenieCompany5 жыл бұрын
@@tonysarmiento4629 the keypad has a "panic" feature built into it, you will (depending on the model) have either 30 seconds or 15 seconds that the lights on the keypad stays on after using. in that time frame any button will activate the door.
@Tankgeeman5 жыл бұрын
@@GenieCompany mine does the same thing and wont take the new code
@Tankgeeman5 жыл бұрын
@@GenieCompany so do you wait out the 15 seconds before programming the new code?
@AveragesasquatchАй бұрын
I thought I did something wrong when the door kept operating after I did the factory reset on the code. Turned it it's just that if you hit any key too soon after putting in the code any key will open it. I couldn't program the new code because the door kept opening. I just let it sit a minute then programmed the new code and it worked.
@marygfullerton2 жыл бұрын
Have tried repeatedly and can’t get past the 357- up down. (Before attempting setting my own code. ) The keypad just fast flashes every time and door never opens. This is the second time this keypad has stopped working for opening my two garage doors…
@soufer2759 ай бұрын
Does it have to be set up before mounted on the wall outside of the garage? We didn’t set it up before.
@GenieCompany9 ай бұрын
It is recommended but not necessary.
@dannydanix86982 жыл бұрын
I did everything you explained on your video, the Genie learned the door opener, unfortunately I tried a new number but every number opens and closes the garage door. Even one digit number. So weird.
@GenieCompany2 жыл бұрын
This is the panic feature of the keypad, as long as the back lights stay on you'll be able to press any button and any key will open the door, this will last from 15-30 seconds. once all lights are off, you can fully reenter the pin
@jayess26094 жыл бұрын
Hey so when i try to program the key pad, it does a few things that are not working. First hitting the program set button and then the cod and UP/DOWN Arrow keys do nothing. As in the door does not move or even attempt to move. The next is that when the door is closed, i am able to use the wireless garage door opener. I enter the factory set passcode and then the UP/DOWN Arrows and the door opens. However if i wait the required time and do the exact same thing to try and close it, nothing happens. Help please.
@GenieCompany4 жыл бұрын
Hi Jay - It could be that you have an older version of the keypad, if you are re-programming an existing keypad, you will need to follow the clearing instructions, and then start completely over, please clarify if this keypad is new, and what model number you are programming it to. Thank you!
@jacobisworld951621 күн бұрын
How Many Doors Can A Key Pad Program
@gaffle-411 Жыл бұрын
These genie external door openers are terrible! The button response is not good and too spongy, plus my units always lose their programming to the openers and I have to do the steps all over again. Very frustrating.
@utubesarah3 жыл бұрын
How do I program a Genie remote from another remote? Button built into car works but I lost the handheld remote. GBO is on 2nd home several hrs away so I can't access actual opener but need to send a remote to repair person.
@GenieCompany3 жыл бұрын
Hi Sarah - This isn't possible, the remotes program to the garage door opener motorhead. If there isn't an existing remote, you would need to purchase one and program it to the garage door openers motorhead.
@priyanshukant34332 жыл бұрын
Can you set two different codes ? Cause the current pin set is same as house door Thanks
@GenieCompany2 жыл бұрын
no you cannot have two PINS, you can reset your PIN or you can use a temporary PIN
@tonyeze7233 Жыл бұрын
my backlight does not come on for resetting the keypad even after installing new batteries.. I wonder why?
@Modelhomestour5 ай бұрын
After I program. Why is it I press the up and down button and the garage opens without me entering the code?
@sirpieman3003 ай бұрын
I cant get this to work on my silentmax 1000 series. When i hold the programming button it only light up blue and does not start flashing purple when i release it.
@GenieCompany3 ай бұрын
Reach out to us at 1-800-354-3643
@mEllzee4 жыл бұрын
What if I don't know the factory default code? I need to program a new code without the old code. How?
@GenieCompany4 жыл бұрын
Keypad would need to be reset, along with reprogramming to the garage door opener motorhead inside the garage, please call us at 1-800-354-3643
@BatRaxx4 жыл бұрын
We set the code but whenever we press any button when opening or closing the door it disrupts the door. It will open the door if closing or vice versa.
@GenieCompany4 жыл бұрын
Hi - this is called the "panic" feature. For up to 30 seconds the lights behind 3/5/8 will stay lit. If those lights are on any button will activate the door. Designed if you forget something and need to quickly re-enter the garage. Wait for the numbers 3/5/8 lights to go out and try again. thanks!
@chandrautube213 жыл бұрын
It helps
@carolmatiszik39364 жыл бұрын
Just bought a new house and going to reset the keyless entry. If I reset the keyless entry does it effect the remote? Would I have to relearn the remote also?
@GenieCompany4 жыл бұрын
As long as you are not clearing out the receiver memory. So if you have a learn code button, do not hold the learn code button in as that will reset the remote.
@samyarobinson83924 жыл бұрын
Genie Company what is the learn code button ? Pls help!
@GDOs4 жыл бұрын
it’s the button that u can use to program remotes, keypads, etc. it is typically on genies black or a brownish yellow, and is located inside the light covers, on the back of the unit, or on the bottom or front of the unit.