Welcome to Enertech University, online training by Enertech. This video from Delphi shows the procedure for repairing an all-aluminum microchannel air coil in the field or shop.
Пікірлер: 118
@Iskandar82434 жыл бұрын
thank you so much, very helpful
@uleoss6 жыл бұрын
My radiator has the very dented fins on some pontoons it does not have! I would like to make the repair more I do not think here in Brazil! where can I find. thank you
@frosttube87933 жыл бұрын
Great video , what's is the liquid type, during pre heating the coil
@emalopez95794 жыл бұрын
Hola una consulta, donde consigo él aletado nuevo para sellar la reparación?
@Vegas-p1w2 жыл бұрын
There's a product outhere called High side red epoxy ,(2 part epoxy)much easier to repair small refrigerant leaks & you can use a heat gun. Works great for low & high side it can handle up to 3000 psi Temperature -100 -300 degrees
@bobharvey33833 жыл бұрын
And where does on get replacement air fin??? I've looked everywhere...
@jayarajjayaraj65495 жыл бұрын
I think it is new one ,old coil corrosion many place,that how can,tell me remedy
@flaviolegu6 жыл бұрын
Top gostei do vídeo vou fazer na minha moto
@moadil59214 жыл бұрын
Tell me what was that u spary on coil plz reply
@bineshchauhan87134 жыл бұрын
Thank you very much sir, Which brazing rod and flux are you used please inform for unknown person or me From Ahmedabad. India
@EnertechUniversity4 жыл бұрын
Hi Binesh, There are probably several brands on the market. It’s an aluminum flux core braze rod.
@fernandorubio90283 жыл бұрын
I'm not convinced about gluing the new disipators, that doesn't seem to be realiable for thermal conduction, seem more like just a cosmetic fix to me. probably doesn't matter considering the overall size of that radiator, but surely matters on small radiators.
@ctrlaltdebug2 жыл бұрын
@@PietriGuitars you'd probably end up with a half-melted mess.
@rodolfoandrade74532 жыл бұрын
I mean, if the glue itself is thermally conductive, then nothing really changes.
@henkelkalberg72193 жыл бұрын
Where I will get spare fins?
@yashpalsinhzala43452 жыл бұрын
Thanks sir very very good knowledge sir 👌👍🙏🏻🙏🏻
@flagstaff8667 жыл бұрын
Where do you get the replacement air fin?
@user-kt8vv7vj3x7 жыл бұрын
-
@uleoss6 жыл бұрын
I want to know
@mcroley5916 жыл бұрын
It comes with the repair kit
@rohitrangari92583 жыл бұрын
What if we cut only bad fins from rediator
@trinito97 Жыл бұрын
How about when you get the leak in the middle of tube
@jayk90637 жыл бұрын
Not once have I found a leak in such an easy spot to fix. Most of them don't even have enough space to fit pliers in straight! And believe me, if they aren't parallel with the channel, you will create a leak in the adjacent channel. Have also come across some systems that have leaked out their charge and have been left unnoticed for up to a year, resulting in 5-6 vacuum pump oil changes through the evacuation process to get below 500 microns due to moisture accumulation.. have never had that issue with copper and I've poured water out of copper condensers. Let alone the rate in which aluminum oxidizes compared to copper. Oil changes in hermetic compressors is gonna become a requirement of a p/m contract
@OcRefrig6 жыл бұрын
Alittle tip for ya --- use dry nitrogen pressure tests and flow dry nitrogen through a unit a few times to Help gather up the moisture. dry nitrogen helps alot ! vacuum for a bit, then dry nitrogen Pressure to 100 psi, then dump the dry nitrogen from the unit, then evac for a bit more . i have flowed a whole bottle of dry nitrogen through systems to pick up the moisture it works good. nitrogen is dry so it grabs onto moisture . speeds evacuation time alot. hope it helps u in the future. dry nitrogen flow while welding also helps make for a fast evacuation time.
@henkelkalberg72193 жыл бұрын
Where r the refrigerant tubes? I can only see the fins.
@abracadabra24446 жыл бұрын
What type of spray paint is the best for corrosion protection? May be it is Alu-Zinc primer?
@arncj185 жыл бұрын
mine came banged up in one area, with shipment, the fins were affected. Should i send it back or will it work
@EnertechUniversity5 жыл бұрын
The coil shouldn’t be affected by a few dents in the coil. Unless there is a refrigerant leak, I would not replace. Thanks!
@emmanuelmartin39992 ай бұрын
where to buy that fins
@dirtywhiteboy49637 жыл бұрын
you should pull a vac when done to get rid of moisture from the outside air and any water that may have entered,thanks for the vid!
@dirtywhiteboy49632 жыл бұрын
@n325aej must have missed it......smart ass
@hamdanhamdancangkau47283 жыл бұрын
Di mana mau beli aliminium utuk welding radiataor
@user-mv7lf4oz1w2 жыл бұрын
أخي الكريم الحمهة فافون مايحتاج تؤخر المشع
@martlndimitrov65383 жыл бұрын
What is the point of removing the fins ??? The whole is clearly visible and repairable without having to remove them .
@ctrlaltdebug2 жыл бұрын
Good luck not melting the fins when applying heat.
@therasemagdalin43342 жыл бұрын
How to purchase
@enetoend46532 жыл бұрын
Welding rode name please
@karimkari96785 жыл бұрын
ما اسم اللحام
@yawemmanuel4380 Жыл бұрын
Cool undercut temperature for
@robertoviacrucis36932 жыл бұрын
Aluminum materials are very sensitive and more time to prepare for repair... And then after a days same problem is there.... We solve sa problem by replacing new aluminum fins coil and copper tube coil.. Its all and aluminum fins to copper coil are easy to repair...
@stefanvalchev80663 жыл бұрын
I belive it is possible to tig weld such a kind of problem
@rajendrasirlucknow94276 жыл бұрын
Aluminium coil better hai....ya copper coil
@INDIAN-bp7ly5 жыл бұрын
Copper coil best
@shahinraju55744 жыл бұрын
I will need it aluminum blazing rod
@jitubhaisondagar72573 жыл бұрын
9725803731
@OcRefrig6 жыл бұрын
YOu want to have Dry nitrogen coming out of THat hole while u are soaping and washing to Keep the water from entering the Coil. Letting soap or water go in the hole is NOT Ok !
@jimk.87832 жыл бұрын
Yes, I cringed when he sprayed inside the hole.
@ctrlaltdebug2 жыл бұрын
LoL make a video repair without cleaning the inside of the tubing, and see how that works for you!
@idahogreen28852 ай бұрын
Thanks Sarge 🖕🏿
@pascoalgomesdossantosgomes8165 жыл бұрын
A única coisa complicada e o cliente pagar pelo conserto,ainda mais no Rio de janeiro,do tem malandro r miseráveis.
@vaivenopatrao50024 жыл бұрын
Top
@kBen19865 жыл бұрын
I like when he continues dumping water at the leak. Let’s try and get water in the system as much as possible. Residential mindset.
@kBen19863 жыл бұрын
@@PietriGuitars Wouldn’t it be better to have the system in some type of positive pressure when spraying liquid water in open area of a refrigeration system? Or should we just be careless and dump a whole gallon in it because the vacuum will boil it?
@jimk.87832 жыл бұрын
@@PietriGuitars Never purposely put water in a refrigeration system. You are just making more work for yourself and it will require a much longer evacuation time to get it all out.
@ctrlaltdebug2 жыл бұрын
Clean out the oil as best as you can. Otherwise the solder will ball up and you will have a charred mess that leaks.
@ctrlaltdebug2 жыл бұрын
@@kBen1986 if you don't wash out the nearby tubing, the oil will bubble out when heated, ruining the solder site. That's the other reason for repeatedly drying and washing again, you must remove all fluid and residual oil from the inner surface.
@maithemabbas22754 жыл бұрын
👍👍👍👍👍👍👍
@ahmedalosif64303 жыл бұрын
that's AC rediter or water raditer
@user-zd3ql5zc2r6 жыл бұрын
ممتاز
@user-lt7js7tu8t6 жыл бұрын
السلام عليكم . سؤال اخي ما الفائدة كم القطعه المعدنيه المربعه لمادا تتم تغطيه جوانب المكان المراد لحامه . انا لا افهم لانجليزي.
@user-zd3ql5zc2r6 жыл бұрын
حتى تتركز النار على مكان اللحام فقط ولا تتآكل الاجزاء الرقيقة من زعانف المكثف او المبرد
@user-lt7js7tu8t6 жыл бұрын
بارك الله بيك وجعلها في ميزان حسانتك .
@pulokeshmukherjee96362 жыл бұрын
Top jio nice very nice Kolkata very good 💥💥💥💥💥💥
@dieniewienie1437 жыл бұрын
so he made more dents in the process? ref.
@MelvinIsMerlin5 жыл бұрын
hurt dur vents can be bent straight
@avutex85476 жыл бұрын
This has no impact on dissipating the heat beside the decorating it.
@EnertechUniversity6 жыл бұрын
Thank you for your comment. The main purpose is repairing a leak.
@HVACRDUDE7 жыл бұрын
try it with 550psi in 127° heat, this doesn't work in the field
@xaviermanning93115 жыл бұрын
I now seeing video I agree don't work
@bhaveshahareeya53675 жыл бұрын
WhatsApp timing problem
@sinoeunruralfood31906 жыл бұрын
Hello brother
@newstart49 Жыл бұрын
When done, flush the coil out with water- don't worry, just pull a vacuum for a week or so.~~~ I might use a soapy damp rag, but I'm NOT spraying the hole with water!! A dry carburetor cleaner pray might be better.?
@idiots8307 жыл бұрын
why not make with copper??
@UKSCIENCEORG7 жыл бұрын
$$$$$$$$$$ That's why
@ryand26787 жыл бұрын
Planned obsolescence is why..
@muthulaksmanan67826 жыл бұрын
Ryan D
@ctyhaak61685 жыл бұрын
Mày làm phức tạp thế hả em
@abdrhman15543 жыл бұрын
راح نص العمرو
@capitainelelouche36996 жыл бұрын
😂😂😂😂😂
@wojtekkowal26526 жыл бұрын
Is super glue conducting heat to the pipe ? What a crap ...
@MelvinIsMerlin5 жыл бұрын
its thermal paste u turd licker....
@jeremy499885 жыл бұрын
I was wondering that myself....also that the replacement fins didn't make contact with the refrigerant tube at the top. But like they said, it's a very small percentage compared to all the remaining fins. I looked up Loctite 430, it says it's especially suited for bonding metal substrates but makes no mention of its ability to conduct heat. I'd rather see those replacement fins a little larger vertically and making contact with the refrigerant tube.
@MelvinIsMerlin5 жыл бұрын
@@jeremy49988 From what ive read loctite 430 is good for up to 200 degrees and even at that temperature isnt the breaking point its the point at which it begins to lose some of its hold.
@ctrlaltdebug2 жыл бұрын
Use thermal epoxy if you want, but don't even need to replace the small section of fins. it's negligible in overall effect.
@MrTralenuvole5 жыл бұрын
Often MCHX producer are using automotive design that are very different from HVAC needs. Often MCHX producers are fighting to reduce costs using less and less material. The effect is that MCHX cores are too light, with thin tubes.. easy to damage. To avoid this tipe of leakage is very important to buy from the right MCHX producer.
@EnertechUniversity5 жыл бұрын
Hi there, we are not in the automotive industry, so we cannot speak to what they do. In many warranty situations, we offer to replace the coil. Repair instructions are offered as an alternative due to concerns our dealers had to offer a quick effective repair without waiting for parts. We try to use the best quality products in our equipment. Sometimes damage to coils can’t be helped. MCHX can be repaired using this method.
@ArunKumar-ny1sk5 жыл бұрын
Materials detial give bro
@MahendraKumar-xi5mz9 ай бұрын
हिंदी मे वीडियो बनाए
@jonminnella21686 жыл бұрын
Not a fan of micro chanel
@MyKonaRC5 жыл бұрын
When out in the field, just bend / crimp it. Cut off the flow of coolant in that cooling line.
@EnertechUniversity5 жыл бұрын
Thanks for your comment! Due to higher pressures of refrigerant in the heating cycle, soldering is the best option. This procedure is recommended by the manufacture of the heat exchanger.
@danielwsookdeo90094 жыл бұрын
It is not a radiator bro
@stevenkarting3 жыл бұрын
Un vrai boulot d'amateur !!! C'est loin d'être une réparation propre et de qualité.
@panjabifanda3 жыл бұрын
😂😂😂 which aluminium was already ok. you are damage the below forged.😂😂😂😂
@abdrhman15543 жыл бұрын
وطريقه فاشله
@yanezfranco5 жыл бұрын
microchannel type condensers suck!
@EnertechUniversity5 жыл бұрын
All-aluminum microchannel air coils are used because they eliminate the potential for failure due to corrosion and increase the unit's life expectancy.
@user-xk5so7wb2t3 жыл бұрын
WoW Ridiculous amount of detailed work, to "fix/repair" these inferior coils. You Know their crap coils when they tell you "DON'T PUMP DOWN COND BC IT WILL BLOW/CREATE DAMAGE TO THE COND COILS N CREATE LEAKS"
@johnpendleton72433 жыл бұрын
Actually, these coils are highly reliable. We have less than a 1% fail rate so less failures than your typical tube & fin coils
@user-xk5so7wb2t3 жыл бұрын
@@johnpendleton7243Interesting. When why cant they hold a simple pump down? bc label stated "Do Not Pump Down"
@user-xk5so7wb2t3 жыл бұрын
@@johnpendleton7243 also they were kinda ok when the R22 (lower Head pressures) in around. R410a pressures, Look out
@ctrlaltdebug2 жыл бұрын
@@user-xk5so7wb2t probably because the coils are long and narrow hot dog cross section and not circular. The long walls would probably collapse under vacuum.
@swainer801411 ай бұрын
There isn't enough volume to store the refrigerant!. It is a fraction of the tubing on plate fin coils.
@texasmade26845 жыл бұрын
These coils are trash
@hid3nax4 жыл бұрын
I get boom from the microphone. Uncomfortable to watch the video, so I discontinued after first 45 seconds.
@robertwojtowicz93310 ай бұрын
Just don’t buy the piece of shit microchannel and you won’t have to repair it !