GEPRC Crocodile Baby LR can fly for 30 minutes???

[@licensetodrive9930]

I'm really liking how the hobby is gravitating towards smaller quads since I started flying sub 3" and have continued to fly sub 5" for years since.

[@sugasheeze]

I agree, I really feel like my 3 inchers fly better than my 5 inchers by themselves. The issue is that 3 inchers can't handle a GoPro nearly as well, so 5 inches is still the most relevant--although less relevant now that we have the Insta360 Go and Naked GoPros.

[@coolhanddruid]

Boring.

[@licensetodrive9930]

@@coolhanddruid As is your comment.

[@coolhanddruid]

@@licensetodrive9930 No you

[@CYDeviant]

@@coolhanddruid Try something like a 1408 4000kv sub 250g 3" build on 4s. Imo you need to maximize power as you go smaller/lighter, and try to maximize smoothness when you go heavier. A quick and very agile 3" build can be very fun, and easier to tune. You can swap out to bi-blade props and fly in a park around people, they won't even notice it. Everyone flies different though.

[@josephmajernik8726]

Joshua Bardwell, I got a new iFight Baby Crocodile and I could not get the motors to arm for anything. I have a Jumper T18 and the analog quad. After watching your video 4 times watching and listening to what the different settings do I finally got the motors to arm. Thank you for all you do for us. I hope you know how important a role you play with all of us quad owners, especially the newbees like myself. Thank you again so very much!

[@quadroneld]

The more review videos I watch, the more I get the feeling that GEPRC is developing into the DJI of the FPV DIY world.

[@jackmaddox4960]

Josh, I agree about the antenna tubes, one solution I found was I ordered the extra thin antennas from banggood and they actually fit inside those little red or clear extension spray tubes that come with WD40 or DeOxit D5 electrical contact cleaner aerosol cans; I went to my local electronics store, and they had bags of them that they found in the bottom of boxes of spray cans that use them... They had clear ones, and gave more than 20 for free. I mention this because it's the best way I found to get them, they're hard to find by themselves in less than boxes of 1000. Anyway, they're indestructible, at least so far for me, and my uniquely crash-heavy style of flying...! Some antennas didn't fit, but the skinny ones did.

[@UncleDudeProductions]

I am really excited about this series. Your Flywoo video sold me on this 4" LR category, hard, and now I not only have more options, but you're doing this direct comparison. Can't wait.

[@GeorgeCooper_LoneWolf]

As a big fan of GEPRC I have been waiting for this review ever since you mentioned it a few weeks ago, and I have to say I'm not disappointed and think this is a great Quad. Yes, there are one or two things they could have done differently such as the cam mount however I find with all ready to fly models there is always something one wants to change. Great review Joshua

[@simonbrunel1747]

Dude, I was in a bad mood. Then, a JB's notification. Now I'm happy again. Thank you for this really cool review!

[@vdubjunkie]

Joshua, I seriously appreciate a vast majority of your thoughts and opinions. So, when I find myself disagreeing, it's worth mentioning. As a network engineer with more than 20 years in the industry, I'd say full functionality and lack of bugs always wins out over running "the latest and greatest" software. Like every time.

[@gus8378]

You could install a tiny toggle switch on the GPS cable to be able to disable it.

[@dieFPVler]

After around a year having the Croc, I can tell buy it. As a beginner, like I am it can give you a taste of different areas like crusing or first simple freestyle depending on hattery. I flew it with 4s 1800mAh chonckers which I already had up to 15 minutes and now with 4s 650mAh which in comparison for my beginner reference is a hellride of agility and climb rate. Also as a beginner the actual need for freestyle-capability is limited - so in my opinion this quad brings more than enough to table to get a taste and learn basic things. How ever I feel as a real bloody beginner, I would not recommend starting with light batterys - the less agile behaviour with heavy batterys is helpfull in the beginning I guess. Also it even flys with 2s 1Ah hattery :)

[@swissfreek]

6:09 my guess is the vista is there so you can access the USB port without a motor being in the way like it is on some others. Same story with the whoop board rotated 45°, in most other builds the whoop board is mounted “naturally”, and it’s just about impossible to mount in a way that you can get to the USB port without taking the whole damned thing apart. Kudos for both of those design decisions.

[@markthompson6334]

Antennas. I found a really cool way to support the wire . I use a zip tie and I shrink wrap my antenna to the tail of the tire wrap...

[@infiniti1269]

Love the Potato Riot shirt :)

[@DigitalN8v]

Is that shirt a cross from potato jet and roto riot?

[@Stand_Tall]

@@DigitalN8v rotor jet

[@SiUmaam]

Wow. nice competitor for Chimera4 and Flywoo LR. My FlyWoo Explorer Analog bringing Session 5 and using 4s 850mah 80c ONBO Cruising Smoothly and got Flight Time 9 min 40sec Impressive for me, and the motors still Cool, no warm even little

[@gcdevicegc6103]

And without session 5.? With 850mah

[@daveopie1234]

LOL!!! "make sure I'm at twelv.... maximum possible output power".

[@bugsy742]

😂😂😂

[@jacobm5186]

As my first non-whoop quad I'm enjoying this. The only issue I've noticed is the current sensor did not work out of the box. I have the Analog and XM+ setup. They soldered the GPS RX wire to where the current sensor reads. I moved the GPS RX wire to the TX2 pin (A02) and remapped that. I then turned on the current sensor pin. Now I get GPS and Current. # resources resource LED_STRIP 1 NONE resource SERIAL_TX 2 NONE resource SERIAL_TX 11 A02 resource SERIAL_RX 11 A08 # timer timer A02 NONE # dma (maybe not necessary) dma pin A08 NONE dma pin A02 NONE

[@joelhiltz3329]

Jason what's your background thks

[@jacobm5186]

@@joelhiltz3329 what do you mean, background?

[@joelhiltz3329]

@@jacobm5186 Electronics Navy training ect thk you

[@jacobm5186]

@@joelhiltz3329 Just Electrical Engineering and lots of diy electronics.

[@quentincampbell5865]

I like this build up you doing. And doing each individual test before the time. Nice one JB.

[@MCsCreations]

Fantastic flying and review, Joshua!!! 😃 Looking forward for the comparison! 😊 Stay safe there with your family! 🖖😊

[@1stslave143]

Josh, take the whole cam with the 3d print away and mount it the other way around. The cam will then be more in the back and safe behind the frame.

[@TheSnow520lee]

I'm using GNB 1100mAh HV 4S... 22 minutes! it weighs only 99g. No issues with GPS on soft serial.

[@MarioIArguello]

The ' flying brick ' architecture seems to still be prevalent in many designs. One of my biggest pet peeves and why I prefer to design my own frames is many designs are still stacking components instead of distributing them more streamlined. And my biggest pet peeve is the front mounted camera with little protection. And you are right to point those things out because the design of any product is not just about mounting components to a frame... There is much more to that ... While stacked components are desirable from a cpmpact form, if the quad frame has the room lengthwise, by all means, use it! Interesting you bring up the ceiling mount of the camera vtx, I did the same on my MIA Zoom years ago, for the same reason that I wanted to have ease of access to the VtX and DVR when I was using the Caddx Turtle system. Except in my case the frame was very compact and it opens like a car hood, you can see that in some of my recent videos.

[@yngndrw.]

When you want to open it up, if you remove the lower front screws instead of the upper front screws the camera and its cable will come away with the Vista and that will give you much more access. (And will reduce the likelihood of you breaking the camera cable)

[@JoshuaBardwell]

That's clever.

[@kelleysislander]

Nice rig, but I do not like the angle of the GPS mount. I would not expect to be flying pitched forward at what looks like 45 degrees. For "normal" flight you may pitch forward maybe 20 - 30 degrees, which presents a less that optimal angle for the GPS antenna. Ideally you would want the GPS antenna to be face-up to the sky during normal flight. It would also be nice if the FC was iNav compatible for true failsafe RTH functionality - nowadays iNav 2.5.2 flies pretty darn nicely compared to earlier versions. While BF may be "best" (or what we are most familiar with), this is not an Acro rig per se, so you really don't need all of that. iNav is ideally suited for LR and cinematic style flying. I didn't mean to make this so much about iNav, but when you start talking GPS, BF is waaaay behind in that aspect ;)

[@robbietiz1702]

thankyou Joshua. Looking forward to watching the rest of the shootout before i start saving.

[@lukeiam0]

Some found Explorer LR has poor GPS locking it's because the GPS wires are not insulated. I have seen couple of videos about it.

[@RCRitterFPV]

small Quiet, 15+ min and GPS return... 1080+ video. (enough to impress mom, haha) tree top, coastline, and mountain surfing eagerly waiting to see who comes out on top of this by Xmas time.

[@ugellin]

Hahaha "I love how the frame has space for 2 battery straps, I'm of the opinion that 2 battery straps are more than twice as strong as one" ... flies it with one.

[@JoshuaBardwell]

On the day of I couldn't be bothered to thread through the top plate :-)

[@ugellin]

@@JoshuaBardwell Haha I don't blame you it just made me laugh. I love your content and really appreciate the response.

[@FPVian]

Just testing it how most are gonna fly it... easy excuse

[@bugsy742]

😅

[@RobsClips1980]

All long range quads should come with high output vtx and diversity rx. I feel manufacturers miss a trick on this front. The CB 4 LR is a great quad but lacks in areas that would make a long range quad excel.

[@mleitner0]

By moving the weight to the back it would make the front motors work harder all the time to counter the weight in the back this is the more efficient design not by space but by power usage.

[@jlarson42]

Great review. I just won the Flywoo LR Explorer frame, looking forward to seeing the rest of the videos. I'll be picking and choosing parts for my build based on your pros and cons. Happy flying Joshua 🤓

[@ozdemirsalik]

“Potato Riot” is an amazing message.

[@zachspross1084]

Can’t wait for the shocker review! I get my frame today!

[@jhughes2286]

This baby croc 4 has 2750kv motors, then the whole time you were flying you thought they were 3000kv? That had to change your view of this quad.

[@DaveyFPV]

I always use two battery straps, even for racing. It's better to finish than have your battery eject.

[@chewsan7733]

Joshua cap can reduce motores noise in the video helps

[@hateeternalmaver]

Those hardware UARTS - when I was on F4 I didn't get all the fuss about it. A little remapping here a little SBUS inversion hack there.... But I recently went F7 and I have to say I'm not looking back at all. ;)

[@chriswatts2054]

Looking into the possibility of a room clearing drone. Fpv, agile but tough. Search and rescue oriented. Long flight time and strong enough fpv and control signal to be able to enter buildings from as far away as possible.

[@EnuffsEnuff318]

The jittery video seems normal on this quad from the other reviews I've seen. But no one talks about it.

[@jt37218]

I noticed the same in a lot the footage of various reviews and also with my own Dave C Micro LR frame built/Vista, especially if there's a touch of wind. They just accept it or gloss over it.

[@seesea9614]

@@jt37218 low speed KV-motor need naked gopro，LOL

[@zico3239]

When using heavy bolts and nuts to replaceable the arms they should make the arms foldable to make the extra weight more effeceint

[@daemn42]

@Joshua Bardwell When you say you were running it at highest power available, do you mean 1200mW? Vista has a known issue where sometimes performance actually decreases as you go above 700mW. I suspect it's a feedback issue and usually this will vary depending on the antenna used on the VTX.

[@willay747]

haha I did the same thing on my baby croc with silencing the buzzer!! Usually you hold it for a few seconds... Nice quad but mine was packed like crap

[@TheMetalSandman]

Joshua, or just anyone. I got this Croc Baby and flashed it with G-H-30 2.3 JESC (48khz) with Telemetry, licensed. Then used Dshot300, 4k/4k, with Bshot "ON" and "12" on motor poles. It won't fly cause some motors are getting "errors," what's wrong with it? XD

[@CsotPet]

What about putting the GPS 5V to a switchable pin? Or using a little board what lets you to switch 5V with pwm signals, like the light switcher boards on RC cars/planes. So you can connect it to a servo output and assign an aux to it.

[@tomfarran6562]

WOW! absolutely beautiful footage!

[@KarlCranny]

Empty space likely helps with cooling, an issue with Cadx.

[@kevinmahoney9205]

In the shoot out video I'd like to see one of these flying with a Crossfire and Shark Byte setup.

[@grownnotflown2]

Excellent work !

[@yannickg6904]

This is only the beginning, these new lightweight quads are like the new toothpicks. Hopefully battery makers will all start making Li-Ion packs.

[@yannickg6904]

@Brandon S WTF is your problem? Twice you did this.

[@Eat_More_Possum]

I too was thinking my controller signal range with the Croc Baby was deficient. Maybe I'll try a different antenna.

[@thisisspartan5953]

Excellent Video ZOHD LionPack 3000 mah for my geprc crocodile baby ....... I used to fly with 4s Lipo.... Do I have to make any change on my setup on (Betaflight or in the DJI fpv goggles) to get the Lion battery voltage reading ? I flue 1 time with the Lion pack and I get the low battery warning 5 minutes after take off. Thank you.

[@sheldonsaintstudio]

Have a look at the Diatone Roma F4 LR.

[@flip297]

BNF version using the Nebula camera :|

[@AidenBrown429]

Imma buy this drone most likely but i gotta say one thing the sales on the tyro79 on banggood is higher than any other drone

[@Dangasaur]

re: vista packaging I've had a tough time on two quads now trying to package the vista. It's quite a bit larger than the 20x20 mounting holes, the position of the UFL connector and antenna can be inconvenient, it's tall, and the fact that you can't easily remove the camera to thread the cable through other elements are all things that have frustrated me at some point. I bet you would have to change a half dozen things about the geprc croc baby to move the vista behind the FC.

[@ekkle5ia]

Hey you can remove the camera connector. Just got to have a tiny torx screwdriver

[@Dangasaur]

@@ekkle5ia I guess a better way to say it is that since there is no plug on the camera side and you need clearance to get a driver onto the hold-down on the vista there are situations where you are stuck vs. analog setup.

[@nandakoryaaa1401]

So did it fly for 30 minutes or not?

[@pedro449]

Hello Mate, thanks for the great review. Could you please show which pads are used to connect GPS in softserial configuration on this FC. I can use LED pad for GPS TX, but I don't know which pad to use for GPS RX? As you mentioned, UART1 is for Vista, UART2 for Crossfire. And I assume that Buzz pad is used for the buzzer? Therefore, the only available pad left to use for softserial mapping is LED pad, but GPS needs 2 pads one for TX and one for RX. I really appreciate if you show how they wired GPS on this particular FC. Thank you very much

[@johncgibson4720]

They are either under 250 grams or can fly for 30 minutes, but not both at the same time. The 4S battery pack itself is 195 grams already. And the drone with lightest option with analog video is 130 grams. It can only be under 250 grams with a 2S pack. And we all know that you can't flip and snap with 2S.

[@509FUN]

Seems like my amp readings are way off, possible causes? Straight out of the box today

[@flexplexico480]

Same with me - any resolutions?

[@evoluman]

Hi Josh. I bought one and have been flying it for about a week. I am having the exact problem as you, where my DJI Googles have 4 bars but my DJI controller has have 1 or 2 bars and turns red. If you find a solution please let me know. I'm emailing Geprc as well.

[@dropshotfishing7808]

Ben did yours come with a Nebula camera ? Thanks

[@markpfeifer1402]

For long range, the only signal strength indicator in the OSD that matters is Mbps in the bottom right of the display. Completely ignore the red indicators on the bottom left. They are wrong and mean nothing...

[@toys5355]

And if this is so, what low value in mbps is “safe”?

[@markpfeifer1402]

@@toys5355 below 10mbps is considered "shaky ground", below 5 Mbps, get ready to go to black screen and drop out of the sky, get your finger on the GPS rescue switch!

[@ZabDevin]

So you’re saying RSSI doesn’t matter?

[@markpfeifer1402]

@@ZabDevin I fly the DJI controller, not crossfire, so I don't use RSSI.

[@divingfalconfpv4602]

Flywoo explorer list their kv as the same on production model. 2750kv

[@DougEfresh.]

I really wish you would do a video on the analog version since I'm sure alot of us are still not rich enough to go digital or maybe just prefer it. Do you see doing an analog version review in the future? I was or am just about to buy the Flywoo, but now these have come along and I am stuck on my choice. I definitely am getting the batteries that last almost 30 minutes since I want to stay in the air a long time. Also I always have used the xm+ receiver. Is it more difficult to set up the R9 or whatever it is? Never used it.

[@thegray1zer066]

First!!! maybe not? Potato riot FTW!! good one again man, when you do the shootout could you do each KWAD in the running with the tbs Tango 2 and whatever other long-range controllers you have laying around, Pls Fren?? do you perhaps have or know someone with one of those TBS ground stations because that would be interesting??? would like to learn which can go the furtererest and how

[@fishfinder3583]

Another great review -thanks Joshua!

[@rcbear5863]

I know the rules are supposed to be 250g but I'm just curious has anyone been stop and a cop pulls out of scale and throws your drone on a scale to see if your over weight and give you a ticket has anyone ever been stopped and had anyone throw their f****** drone on a scale that had any legal Authority just curious I've yet to ever had this happen also I really don't care about the weight limits I fly whatever I want I try to roughly stay within parameters but if I go over I don't care I'm 45 years old never owned a license but believe I drive everywhere as I want

[@arycave]

For LR reviews I would ask to mention if the FC is supporting iNav....

[@n8lbv]

Hi, this video is titled "can fly for 30 minutes???" This is a LONG video that seems to cover about everything except flight time. I sent this link to a friend who was looking for information on something that can fly longer. Sent him this link figuring this would be discussed in detail from the title alone LOL. Do you have a different video that gets into longer flight times? This certainly is not the one. Thanks!

[@JoshuaBardwell]

I will be doing an flight time comparison of all these guys in the "shootout" video that follows the individual reviews. But the Baby Croc definitely can fly for about 30 minutes when using the 3000 mAh 4S LiIo pack that GEPRC sells (or a similar pack).

[@n8lbv]

@@JoshuaBardwell Excelllent! Thanks! I had no clue 30 minutes was possible. I'm pretty out of touch with newer stuff. Will need to get back in touch.

[@gcdevicegc6103]

Hi! Did geprc change PIDs from original?

[@viktor67990]

I've never had an issue with screwing down tpu on my geprc elegant 5". It just sits there no matter what. And even when other screws get loose from crash, the ones that screwed on top of the tpu part are still tight.

[@marcinm7285]

After watching Your movies I decide to buy Crocodile Baby with vista vtx. But it is a big shit. In oryginal configuration it do not have the current sensor. But the worst thing is that FC is restarting each time after 3 to 10 min. I changed the FC to the new one and the situation is exectly the same and there is no solution for this. Now I am fighting with the shop to give money back becouse this quad/FC inside is tottaly useless.

[@codylogue1622]

Hi, Mr. Bardwell! I just purchased the Baby Croc as my second fpv drone (my first is an Emax Tinyhawk II). I've run into some problems setting it up in Betaflight, though, my main one being that I lost my soft serial port and my GPS is not showing up. It was working fine when I set up the GPS failsafe using your recommended settings, but I must have accidentally messed something up. I tried resetting it to defaults in CLI but it didn't fix it. I'm fairly new at FPV and don't know what to do. Can you help me?

[@pickleeggs3340]

better off asking reddit😝😝

[@hodiheni9145]

17:36 stm32F405 target? But my real question is, if I have Dji goggles2 and vista/old unit, how can I use it with this drone? I had v1 goggles worked fine on 4.1.1. on softserial (original Dji osd) but I pluged a g2 compatible flashed unit on this drone and no osd. What Bf version can I use to work? THX!

[@daemn42]

One obvious way to disable GPS Rescue is already shown in the vid. Enable arm without fix. Power up and launch immediately and GPS Rescue will be disabled until next disarm.

[@vaibhavsethia4280]

Can you please do a build guide on making a drone with dji pfv optical flow sensor ultra sonic sensors and barometer, gps with compass and if possible telemetry also and what to do in inav after building this type of drone. Please please please please please.

[@BubbyFPV]

Lol

[@wongalahara8196]

But why?

[@boratsagdiyev1586]

if you watch all his videos and combine them you have the answer.

[@wolffpv535]

Wrong hobby friend. Check out inav videos, they may have the solutions you seek.

[@vaibhavsethia4280]

@@wolffpv535 I just love autonomous flying with the speed of fpv drones.

[@DigitalArtisan77]

Is the gps a compass also? If so maybe moving everything away for interference. 10cm is reccomended on a matek.

[@blissbouwerij4033]

It's not like you to advertise "clickbate" title Josh. Did you come close to the 30 minute and 40 minute flight times advertised?

[@Burn377]

Watch the video?

[@bernardthongvanh5613]

could you type 'resource' in the CLI to see on which pin the softserial is assigned? I erased mine while flashing and the I need to reassign the softserial, thanks.

In general terms, for a given budget of let's say 200 bucks and FPV, would you recommend some of those "ugly" kits or a fully built DJI-like drone?

[@ipravoqator]

hello, what is the duration of the flight with a naked gopro? with a lipo battery and with li-ion? how big is the battery?

[@dustynrodeo4874]

Man i bought the pnp version and still cant find the pin layout for the fc to add my r9slim + using f port. It either too new of a board or not the correct one and the board itself has no labels

[@nonplayercharacter9653]

Looking forward to the Chimera 4" video. Seems like a better design.

[@timevans6235]

kzbin.info/www/bejne/rKu4oql4hdychtE

[@alessandrofinazzerphotography]

Good morning Joshua, I am your follower, I am Italian and I live in the Dolomites, indeed I invite you if you happen to come to Italy I wanted to ask you for advice if possible, I bought a Croccodile Baby but I have a big problem, I can't configure the Osd on the Google DJI. The doors and the OSD are all activated but nothing appears on the display. On the other drones I saw that not having the DJI remote control but a Radiomaster TX16S I disconnected the cables from the Air unit camera as described on each model, instructions that I followed from my FC which is an iFlight and I see the OSD correctly on the viewers but from Caddx Micro I do not know how to do if this is the correct solution for the configuration of the OSD in your opinion, otherwise I cannot find the solution. By chance you could help me, flying without knowing how much charge remains is practically impossible

[@chip2034]

Is the satellite five a big deal I have already purchased this one but I’m starting to think about the satellites is going to affect explain

[@fuba44]

Can't find the shootout video, is it out yet?

[@J2_P]

Did your baby croc has an accurate current sensors? Mine can not be calibrated because maximum scale value is not enough. Did you have some advice? Replace resistor on FC?

[@JoshuaBardwell]

Current sense does not work on that FC.

[@KenjiFPV]

How much amp draw were you getting on the Lions and what is the max discharge rate of the Lions?

[@Pnada777]

For cruising (30mph) like 7-10A depending on wind. Punchout is 20-25A for me and the problem is not the lion cells, good sony vct6 can do 40A. Check the quality of your wires if you want to build your own pack. Cheers and happy flying!

[@mikewood7946]

love the in depth reviews and ive been looking at this class of kwads since i heard about the explorer can you do one of these kwads with a analog split camera setup? I think there are alot of us out there thats not ready to go dji yet

[@android131619]

Nice video bro, does this motors 1404 2750kv works on 6s?

[@FlyNorthRC]

Do you have a Dump file you could share? Bought one used, and it's been screwed up...

[@phillipdelfmoore6716]

Can you get the baby croc ready to fly out of the box ??

[@leoponce82ponce]

@Josha Bardwell .. Is there enough space inside the baby croc 4" to replace the Caddx Vista with the Air Unit? ( i really want the on board DVR. (Also, great videos please keep posting) PD: when is the comparison between long range qwads gonna drop? ) thanks!

[@JoshuaBardwell]

There is enough room front to back between the standoffs, however you would have to relocate the capacitor. I'm not sure there is enough room top to bottom above the FC, but in theory you could use longer standoffs.

[@chip2034]

Show us step-by-step what to do in beta flight Loring the voltage for ants or GPS settings you just go straight to the source we need to start seeing exactly what to do and how to do it from start to finish and beta flight

[@MrLemurenAffe]

A bit late to the party amazing video Stupid question Can you use your "normal" 4s lipo you would use on a freestyle 5inch (1300-1500mah) What happens if you would use it Thanks in advance

[@JoshuaBardwell]

It'd be too heavy. The quad probably would fly but handle badly.

[@MrLemurenAffe]

@@JoshuaBardwell thank you So the more mah wouldn not affect any electronic? And keep up the amazing work always an inspiration I wish here in germany we could fly so freely

[@mauricevieren]

How is the sound/loudness compared to the Flywoo explorer? 😊

[@butcher]

I do not like this direction. I want x-class for everyone! :D

[@wongalahara8196]

We want both!

[@KenjiFPV]

i want XX class🤣

[@licensetodrive9930]

I think XXX class is already happening, people making naked GoPros & Caddx Vistas to ride their quads...

[@ferdifant_fpv686]

Dem manned kwads 😂😂

[@boom7837]

Lol

[@checkeredflagfilms]

Another thought. Can you actually fit/mount the naked gopro along with that 3kmah battery?...have you tried it. I would require higher resolution. thanks

[@hankbizzo5]

So it is safe to fly with 120c without blowing anything? Btw the buzzer is flipping annoying.

[@Cyrilmtx]

Thanks for the video, what is the autonomy with a 850 mAh ?

[@dukevah]

Thank you for the review. Is there any reason you don't show the pid values of quads in this category?

[@markomilosic3316]

and what about the ghost system

[@dengorc8364]

Please add the forthcoming Diatone Roma F4 LR too