I recently picked up a 1950's Beaver Tools 6" jointer that the exact same design as your jointer, so this is perfect! I'm fixing it up and after sharping the original blades (although getting new ones, on order) I want to still get it running so will follow our instructions. I probably won't keep this old machine forever, but it is nice to get old iron up and running!
@ghostses Жыл бұрын
That's cool! Good luck with your project! Take care, G.
@dinacusic78292 жыл бұрын
I just bought this jointer at a yard sale and I can't thank you enough for these videos on this jointer. I picked it and a belt/disc sander for $80. Definitely a steal and I'm excited to get them up and running!
@ghostses2 жыл бұрын
Glad the videos may be helpful. Yeah, you stole them no doubt! Good luck, G.
@Mayalecabot9 жыл бұрын
Thanks, I inherited the same jointer and decided to fit it to my Shopsmith as the accompanying motor was not in good shape. It's been sitting in a damp garage for 15 years so it was quite rusty. So today I decided to get all the rust off and I will be sharpening the knifes as they are not in good shape. Seeing this video will help to ajust the knifes the right way the first time as I have never done this before. Thanks again, great video.
@ghostses9 жыл бұрын
Alexandre, good luck with your project! It's a great little jointer. I have a video up on sharpening the blades that might be useful as well. Take a peek if you like. Take care, G.
@davidheins87543 жыл бұрын
I used your method replacing the knifes on my Rockwell jointer, it worked well and took very little time to do. Thanks for your video.
@ghostses3 жыл бұрын
Good deal David! Glad it was helpful in getting yours installed and adjusted. Take care, G.
@csimet2 жыл бұрын
A old video on the process, but remains one of the best explanations. I too have an old 1960s Rockwell 4" jointer I inherited from my dad a couple years back. The only improvement on the process was a magnetic knife aligner I got for it. Do yourself a huge favor and get a set of thin wrenches too! It is a tight fit getting at those blade bolts. ;) I'm in the middle of building a new cabinet/stand for it and plan to cleanup the jointer, possibly even give it a new paint job.
@ghostses2 жыл бұрын
Thanks! Yeah, a super thin wrench is needed- no doubt. I ground one down to fit but can't remember the size. Good luck with your project, G.
@howardhagadorn94439 жыл бұрын
Thanks for a great video. I thought I knew what I was doing, but your way of doing it makes way more sense and will result in greater accuracy.
@ghostses9 жыл бұрын
Thanks Howard! I really don't know if this is the best way, but it's my way and works great for me. Good luck and take care, G.
@ethanweikleenget97474 жыл бұрын
Thanks for the videos on this old jointer! I picked up the same one and you helped me to sharpen and reinstall the knives.
@ghostses4 жыл бұрын
Good deal Ethan! Glad it was helpful. Take care, G.
@MRrwmac10 жыл бұрын
Another very well done instructional video! Nice jointer, now that you have brought it back to life! Thanks for sharing.
@ghostses10 жыл бұрын
Thanks Mac. I'm quite pleased with it. All I have left to do is make a chute for it to hook up to my dust collector. G.
@joedodge559 жыл бұрын
Really good video. I bought one of these about a year ago for $25.00 from a gentleman who had an under powered motor with it. I am fixing it up and I was a little confused about setting the blades as the manual was unclear. I needed a small jointer and this fit the bill. Great video and I will look at your vid on sharpening the blades. Thanks again.
@ghostses9 жыл бұрын
You stole that jointer Joe! That was a great buy. For as little as they are, they're built like a tank. Glad the video will help. Good luck, G.
@Soquelite4 жыл бұрын
Thanks for this excellent video. I have been putting off changing the knives on my 37-130, and now I'm ready to proceed.
@ghostses4 жыл бұрын
Glad it was helpful John! It's not that hard- just take your time. Good luck, G.
@Soquelite4 жыл бұрын
@@ghostses It was a snap. As you say, just take your time. Thanks, again.
@ghostses4 жыл бұрын
@@Soquelite No problem John! Glad it wen't well. G.
@johnluna3229 жыл бұрын
Very helpful video. Thank you. I recently bought a Rockwell 37-220 6" jointer on CL for 100 bucks. It's in great shape, too. I just need to sharpen the existing knives and/or buy new ones - I think I'll do both. Anyhow, your video will help me set the blades in correctly and more importantly have them leveled to the out feed table. Thanks, again!
@ghostses9 жыл бұрын
John Luna No problem John! I'm glad you liked it and found it useful. Great deal you got on your 6"!!! I do have a video posted on sharpening the knives off-hand. You might check it out. Granted it's for 4" blades so they're a bit easier to handle, but you might be able to clean up yours using my methods. Good luck with yours! G. kzbin.info/www/bejne/aKOqiIetpKZkfZo
@fred11538 жыл бұрын
Very clear, helpful instructions. I just replaced the knives in my old Jet JSL-6J 6 in. Jointer. Working great now. Thanks!
@ghostses8 жыл бұрын
Thanks Fred! I'm glad it was useful. Good luck, G.
@ridingmanone7 жыл бұрын
Thanks or making this video. My dad left me one of these jointers and your video helped me tune it up and get it going again!
@ghostses7 жыл бұрын
No problem Richard! Glad it helped you get yours going again! Take care, G.
@milktomeathebrews61487 жыл бұрын
ghostses where do you buy these jointer knives? I have this same model and am wondering what knives to purchase to replace the old beaten up ones.
@ghostses7 жыл бұрын
I resharpened mine. I have a video posted that shows the process if you want to try it out. kzbin.info/www/bejne/aKOqiIetpKZkfZo I did find a listing for knives that claims to fit this jointer- though I can't confirm. Hope both help. Good luck, G. www.amazon.com/19-HSS-Planer-Blades-Walker-Turner/dp/B002O75HTG
@toddpommier62054 жыл бұрын
This is a great video. I feel like I can tackle this now, when I had no clue before. Thanks!!
@ghostses4 жыл бұрын
Thanks Todd. Glad it we helpful. Good luck, G.
@pjhalchemy10 жыл бұрын
Wow G, that was really a big difference with your shavings. Really uniform in width and length. Your setting technique was also interesting and pretty quick for such good results, and obviously effective!! Very appreciative of the work you did on this project...really will help a lot of folks out there. I know I learned a few things! Now the work begins, eh? But now with good sharp tools, it always makes the job easier I think. As always, Thanks for sharing! PJ
@ghostses10 жыл бұрын
A bid difference for sure! I used info from the manual, and injected what they did not cover. Yeah, I'm gearing up for the work- I've been doing the work before the work..lol Sharp is always better for sure. Thanks again, G.
@alainseguin82084 жыл бұрын
Thanks for this great video. I feel more confident doing it that way.
@ghostses4 жыл бұрын
Thanks Alain! Glad it was helpful. Take care, G.
@davidsauer80729 ай бұрын
Thanks for this video! I recently bought an old planer just like yours and have been wondering how to change the blades. Very helpful1
@ghostses9 ай бұрын
Glad it was helpful. Good luck and take care, G.
@hankus25310 жыл бұрын
Reading my owners manual your blade setup is almost identical to my that of my 50's vintage 4 3/8" Craftsman jointer. They would have you tap the knifes down with a piece of hardwood, and they do call out a 1/16" projection for the left hand side of the blades for the rabbet cut alignment. I just finished replacing the cutter head bearings and it's running like a new machine now.
@ghostses10 жыл бұрын
That's interesting Hank. My manual didn't have a call out projection, or even mention it. I guess I did good since I ended up with about a 1/16" by guessing. I changed my bearings as well and it made a huge difference. Sounds like we both have good running machines now! Thanks, G.
@thomastieffenbacherdocsava15497 жыл бұрын
You're my go to guy for advice. always in depth explanations. Bought the HF saw blade sharpener after watching your video. Happy New Year!
@ghostses7 жыл бұрын
LOL! Thanks Thomas! Hope the sharpener is serving you well. Take care, G.
@chesterdoble30227 жыл бұрын
Thomas Tieffenbacher/DocSavage45
@04658IFH7 жыл бұрын
Very useful information. I wasn't sure how I was going to register the knives for rabbeting. Off to the basement to put this into practice!
@ghostses7 жыл бұрын
Thanks! I'm glad you found it useful. Good luck getting yours dialed in. Take care, G.
@danielflinn76877 жыл бұрын
Fantastic video. Thank you for explaining this in detail!
@ghostses7 жыл бұрын
Thanks Daniel! Glad you found it useful. Take care, G.
@faisalsayeed38834 жыл бұрын
Excellent video....this was great help. Thanks for sharing.
@ghostses4 жыл бұрын
Thanks! Glad it was helpful. Take care, G.
@faisalsayeed38834 жыл бұрын
Cheers. One question; what size of wrench did you use to loosen the blades? the area where the blades are located is very narrow for a normal wrench ;-)
@ghostses4 жыл бұрын
@@faisalsayeed3883 I don't recall the exact size, but I had to grind it down to fit in the slot. Hope this helps, G.
@MotecM3 жыл бұрын
Thanks for posting this video, super helpful!
@ghostses3 жыл бұрын
No problem! Glad it was helpful. Take care, G.
@entrthedragon10 жыл бұрын
I set the blades a couple of days ago. I took quite a few tries to get them just right. I noticed the blade would sometimes lift a little as I tightened the bolts. Another problem is that the blade would sometimes seesaw when I pushed down on one side to set the blade. I've ordered some strong magnets to make a magnetic jig, I think it might make things easier. A word of warning is that the bolts seem to be a soft metal and not hardened. I learned to slowly, constantly adjust the wrench, pushing it into the bolt head. If you don't you risk stripping the bolt head, which could cause a big problem in trying to get it off. If a bolt head looks like its losing its shape, replace it. Even at the cost of $8 a bolt it's worth avoiding the aggravation.
@ghostses10 жыл бұрын
That's cool. It's tricky to get them just right like you said. I think making a jig with magnets will help things along. If you make two and link them together, you can probably hold down on it while you tighten up the bolts. That might help with the slight lifting you mentioned.You're also correct about the bolts being soft. Mine had one mostly rounded off when I got it. I think the previous owner was trying to turn the bolt CC, instead of CW to remove the bar. That may be why my blades were so shot...lol. Do you have a source for bolts? I would like to get one to replace the marginal one on my machine. Thanks, G.
@Mrflashlite6 жыл бұрын
Hi I redid my jointer a couple of years ago and replaced the bolts, I got them from a site called Renovo I think. @@ghostses
@ghostses6 жыл бұрын
Thanks for the tip! Take care, G.
@M5tworude2 жыл бұрын
A big help, thank you
@ghostses2 жыл бұрын
Glad it was helpful Stephen. Take care, G.
@TheDisorderly110 жыл бұрын
Nice work man. She runs like a top now.
@ghostses10 жыл бұрын
Thanks! That she does... G.
@MikeMurdochMusic3 жыл бұрын
Great vid. Thanks!
@ghostses3 жыл бұрын
Thanks Mike! Take care, G.
@SpartyLinguist4 жыл бұрын
Very helpful. Thanks!
@ghostses4 жыл бұрын
Glad it was helpful Matt. Take care, G.
@blackfender1007 жыл бұрын
Excellent tutorial thank you.
@ghostses7 жыл бұрын
No problem Joe! Take care, G.
@BackyardWoodworking10 жыл бұрын
Good going you have a nice tool for the money. Thanks G
@ghostses10 жыл бұрын
I agree Roland. It works great now. Thanks, G.
@JohnDoe-kp3sw5 жыл бұрын
Sweet little jointer you got there
@ghostses5 жыл бұрын
Thanks JD! Take care, G.
@bertjacobson95502 жыл бұрын
Thanks bro helped big time 👍👊
@ghostses2 жыл бұрын
Thanks Bert! Glad it was helpful. Good luck, G.
@lauriealexander97004 жыл бұрын
Now this makes sense, you set your cutter edge at "0" to the table out feed. Why do I keep seeing people telling you to put blade edge higher than the table out feed and call it "0". As I understand it, the blades should clear the cutter block by the manufactures setting, my case 0.7/0.8mm, but the blade edge should be at "0" with the table out feed. The table out feed edge height is adjustable like yours. Then you adjust and calibrate the table in feed to match giving a true total table feed as "0". Your version makes sense, maybe we are both wrong but I go with this version.
@ghostses4 жыл бұрын
I wen't by the original instructions for this jointer, but setting them to same height as the out feed makes sense to me. If the out feed is too high, the work will hit the table. I see if it's too low, once the material passes over the cutter- the downward pressure on the work will cause it to tilt and gouge the work. This way works for me so that's the way I roll. Good luck, G.
@tomgallagher85327 жыл бұрын
Thanks for the help, I really needed this.
@ghostses7 жыл бұрын
No problem Tom! Glad it was useful. Good luck, G.
@alero6662 жыл бұрын
THANKS GREAT VID . VERY USEFUL . IN WONDERING WHAT WRENCH SIZE ARE THE BOLTS IN THE LOCKING BAR
@ghostses2 жыл бұрын
Thanks Vince. Glad it was helpful. It should be a 5/16" wrench. It needs to be pretty thin to fit in the gap. I actually used an 8mm garbage wrench and ground it thinner to fit the slot. It was a little loose of a fit, but worked. 5/16" would be better though. Hope this helps, G.
@cando96097 жыл бұрын
Nice video and thanks for sharing.
@ghostses7 жыл бұрын
Thanks! Take care, G.
@edwaggonersr.74469 жыл бұрын
I'm watching your series of videos on the Rockwell 4" jointer. I have the same jointer, like you say, the jointer is a tank. I am considering trading up to a 6" jointer with a longer blade so that I can joint longer boards, but I really don't know the limits of my little jointer. You have had over a year using your jointer, how long of a board can you straighten? I sometimes need to joint the edge of an 8' board, but this is rare.
@ghostses9 жыл бұрын
Ed Waggoner Sr. Ed, probably about 6' is the longest boards I've ran through it and didn't have any problems. You might consider setting up and out-feed roller to receive long boards. I wouldn't mind having a 6" so I could run wider boards, but other than that, the 4 works out well for me. Hope this helps, G.
@edwaggonersr.74469 жыл бұрын
***** Thanks for the prompt answer. A fellow craftsman suggested a ratio of 2:1 which is close to your experience. Some think that all boards destined for furniture should be ripped to 4" and glued back together to relieve internal stress, this sounds plausible.
@ghostses9 жыл бұрын
Ed Waggoner Sr. No problem! Ripping and gluing does sound plausible. Good luck, G.
@woodbutcher9518 жыл бұрын
very well explained
@ghostses8 жыл бұрын
Thanks! I'm glad you found it useful. Good luck, G.
@kokenhammer3 жыл бұрын
Good stuff mate
@ghostses3 жыл бұрын
Thanks, G.
@chivone21 Жыл бұрын
I wish you showed how that table adjusts up and down!! Those little handles under each side don't move the table. I gave them a few shots of Wd40, to no avail. What am I doing wrong???
@ghostses Жыл бұрын
Turning the cranks it what makes the tables go up and down. On the back, there should be some small screws- loosen them up then try again. To me, it sounds like yours is seized in some way. Get a penetrating oil - not WD. Let it soak and try again. Don't force anything. Take your time. Hope this helps, G.
@sharr69713 жыл бұрын
I have he exact machine! My neighbor passed away and his wife gave it to me! Can you tell me what blades to use, and also, mine seems to the turning to slow! It only has a 3 inch pulley on the motor! Is that the problem?
@ghostses3 жыл бұрын
William, look though the comments as I know I've linked to some knives that should work. Amazon I believe. If the cutter-head pulley size is correct, I think (don't quote me) the motor pulley should be 6 or 6.5 as I recall. Try to find the manual online to be sure. Good luck, G.
@leighwright86335 ай бұрын
I have a problem with my 2801 Re beaver jointer . I would be so grateful if you could help? Just bought it 2 days agoand got ripped off as there's something wrong with the motor 🙏🏻🙏🏻
@ghostses5 ай бұрын
Uh, sorry- if there's something wrong with the motor- focus your efforts there. That's all I can say. Good luck, G.
@eroshtik69978 жыл бұрын
Thanks great job
@ghostses8 жыл бұрын
+irosha ki Thanks! Good luck, G.
@hugoorantes96808 жыл бұрын
really good video. thanks!!!!
@ghostses8 жыл бұрын
Thanks Hugo! Take care, G.
@011CJ5 жыл бұрын
Thanks for the info
@ghostses5 жыл бұрын
No problem Casey! Take care, G.
@wayneblalock877 жыл бұрын
I have one just like this one I just watched, blades need sharpening which I will do. PROBLEM ..one of the bearings seems to be a bit dry, and of course it's pressed on. Is there a bearing replacement available and a guestimate of what it would cost for the repair. If you have an address I would appreciate it. thanks for the tutiorial, been looking for this for awhile. . I've had this one at least 20 yrs and no manuel. A yard sale find... Thanks
@ghostses7 жыл бұрын
That's cool Wayne. If yours is a 37-290 model, these are the exact bearings I used on mine- and where I purchased them from. www.ebay.com/itm/Vintage-Delta-Rockwell-Milwaukee-4-Jointer-Cutter-Head-Bearings-Set-of-2-87502-/221842945900?hash=item33a6deb76c:g:5IYAAOSwjRpZQwMY I used a Harbor Freight bearing separator to remove and install them. You can find 20% off coupons online. www.harborfreight.com/Bearing-Separator-and-Puller-Set-62593.html This video shows the tool, and it's use. You'll have to jump around the video some to see the whole process. It's not that hard to change them out. kzbin.info/www/bejne/sGOXXmWLjaamsM0 Here's a link to the manual! Hope this helps, G. www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&ved=0ahUKEwjPsPG6i9vWAhUL3GMKHQcLDe8QFggoMAA&url=http%3A%2F%2Fvintagemachinery.org%2Fpubs%2F698%2F2201.pdf&usg=AOvVaw2kRcnMNMTXpUnECS7Ye4F-
@entrthedragon10 жыл бұрын
Great video, I'll be referring to it soon. I'm just about done refurbishing a 37-290 I just bought. You're right, solid as a rock. I know they occasionally sell the retracting casters on ebay but they're expensive. I'm thinking about putting threaded casters through the center hole on the feet which is 3/8. The legs look like they'll handle it. Have any luck getting an original belt? I can't seem to find the right size that doesn't have the teeth on them (called a utility belt).
@ghostses10 жыл бұрын
Thanks Dragon! Good luck with yours- I'm loving mine and they are heavy and solid for such a little machine. On the casters, check out this guys videos on his channel for other caster ideas. I just saw it the other day and he's come up with a brilliant retractable system on a variety of tools. I would feel better with something like it over just using locking casters. This machine is so top heavy I would consider something like he's done. If I ever put mine on casters, his idea will be my choice. Retractable Casters for Power Tools For the belt on mine, I'm using a Fenner PowerTwist belt. I run them on most of my tools and love them. But, if you want to run a standard V-belt, try to look for power transmission suppliers. There may be one in your area They would probably be your best bet to find the proper machine belt- without the teeth. Good luck, G.
@brendameyer44106 жыл бұрын
entrthedragon i
@jamesrogers25329 жыл бұрын
Blades were taken out for sharpening but i cant remember who did it! Need blades. Where to get? Jim
@ghostses9 жыл бұрын
James Rogers Jim, this link claims to fit the 37-290. Hope this helps, G. www.amazon.com/gp/product/B002O75HTG/ref=pd_lpo_sbs_dp_ss_1/186-8376621-7798201?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=lpo-top-stripe-1&pf_rd_r=1NNF37PZBDNKFT951NS4&pf_rd_t=201&pf_rd_p=1944687622&pf_rd_i=B00004RK6L
@bain587210 жыл бұрын
Does new Jointers have the same blade holding system? Great vid as always.
@ghostses10 жыл бұрын
I'm not sure Bain. I do know some have adjusting screws so you can adjust the knives. There may be some that are more like this one- but again, I'm not sure. G.
@jeffchockley26737 жыл бұрын
I have a jointer just like this has been sitting in the garage for about a year i guess its time to try to get it going. So I greatly appreciate your videos ! I thought I would have to buy new blades but with your video i was able today to get two of them sharpened . Will probably finish it up tomorrow and hopefully get it put back together. I was wondering if you could tell me where you found your model number. Mine has a tag that tells the serial number that tag is on the back . There is also a tag on the front that says Homecraft Delta . But i dont see where the model number is. Thanks.
@ghostses7 жыл бұрын
No problem Jeff! Glad the videos were useful. My plates are exactly as you describe- none with a model number. I looked at pictures on the web and determined mine to be a 37-290 Deluxe. Why they didn't put the model on them is beyond me. Hope this helps. Good luck with the rest of your build! G.
@jeffchockley26737 жыл бұрын
Thank you. Im guessing mine is the same.
@ghostses7 жыл бұрын
No problem! G.
@jonathan3518 Жыл бұрын
Any advice of a frozen out feed table on this jointer 😅
@ghostses Жыл бұрын
Loosen up the gib screws, saturate everything with a penetrating oil and let it sit for a long time. Don't force anything. Give it time, no matter how much. You will get there. Good luck, G.
@DarronRansbarger8 жыл бұрын
What kind of wrench are you using to tighten those bolts? I have a Rockwell 6 inch jointer (likely manufactured in the 1970s). The bolts are 5/16 inch but I cannot find a thin enough wrench to get down in there. All the wrenches I can find in 5/16 are 5mm thick, but I have determined that I need one 4.5mm or thinner. Any help is appreciated!
@ghostses8 жыл бұрын
Darron, I had the same problem with mine. I used my bench grinder to grind an old wrench thinner so I could get it down in there. Not glamorous, but it worked. Hope this helps, G.
@DarronRansbarger8 жыл бұрын
Glad to know I'm not alone. Ultimately, after purchasing 2 separate wrenches on Amazon and failing, I got a small Craftman set for $20 that included a thinner wrench.
@ghostses8 жыл бұрын
Darron Definitely not alone! Glad you were able to locate one that fit. Take care, G.
@kholmov18 жыл бұрын
8mm
@michaelcave35207 жыл бұрын
just take a cheap 5/16" wrench and grind it thinner. Much less headache than trying to find one that fits.
@docroot4623 жыл бұрын
Where can I get replacement bearing retainers for this jointer?
@ghostses3 жыл бұрын
I don't know- perhaps Ebay? G.
@jonathangagne53335 жыл бұрын
Thk ! What is the jointer model ?
@ghostses5 жыл бұрын
Jonathan, it's a 37-290. Take care, G.
@SARSteam4 жыл бұрын
Hi ghostses. Thanx for putting this info on video, Awesome !! I got this jointer this week from a guy who inherited it from his dad and has no use for it (Stood in his garage for 20 years, after dad). The whole machine was rusted beyond belief ... I am asking everyone watching this if there is a link to this machines owners / users manual that I can download it ? As far as mine goes, some parts of the fence seem missing but the restoration process is 50% complete. I had to remove the old paint, replace some bolts and nuts and repaint is planned for the coming week. Also I am having the blade mechanism's bearings and the motor bearings replaced, so that should be done within next week. Cant wait for final assembly. So I am watching your vids with eagle eyes this week :D - Update: I found the manuals on Vintage Machinery . com
@ghostses4 жыл бұрын
I was just getting ready to send you to Vintage Machinery to locate the manual but then saw your update. That's Keith Ruckers website. He has a machinery channel on KZbin. Ebay will probably be your best bet for finding anything your missing. Good luck with the rest of your project. G.
@SARSteam4 жыл бұрын
@@ghostses Many thanx. That is one awesome website... Never knew there were so much vintage fandom going on :D
@ghostses4 жыл бұрын
No problem! Yes there is. Keeping old iron alive is the game. Much better that what is being produced these days. Take care, G.
@terryjones83607 жыл бұрын
Where can I get a manual and where can I get the blades?
@ghostses7 жыл бұрын
Here you go Terry! G. Manual: www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0ahUKEwj10-C52Z3WAhUDslQKHXhfBU0QFggoMAA&url=http%3A%2F%2Fvintagemachinery.org%2Fpubs%2F698%2F2201.pdf&usg=AFQjCNFVRxRLtbWJwVMX6QZ5ztnQ2RiGgQ I believe these blades will work: www.amazon.com/19-HSS-Planer-Blades-Walker-Turner/dp/B002O75HTG
@terryjones83607 жыл бұрын
Thank you so much. I got it! Great video by the way.
@ghostses7 жыл бұрын
No problem Terry, and thanks! G.
@dblood85296 жыл бұрын
Where can I find these blades?
@ghostses6 жыл бұрын
I know I've posted a link in the comments to Amazon for them before. I have many videos related to this jointer so I don't know which contained it. I would search around Amazon, or through the comments on my videos. Not much help, but good luck nonetheless. Take care, G.