Fair play to you doing the installation there and then, a guy just reading the instructions and doing it bit by bit, looks fantastic, think of the safety aspect, more brake lights and bright ones at that too, can’t be a bad thing.
@terryboyle3 жыл бұрын
To your closing comments, doing the job a second time would not take half as long. I once had to install ceiling fans, first one an hour, second 20 minutes, and and third 15 minutes. Thank for showing me the process. definitely worth adding them.
@redratthezip4 жыл бұрын
Thanks for posting. I am actually looking to add this to my V56 case on my GS.
@theodorehoag64983 жыл бұрын
Thank you for this video. If you install any of the other accessories on your 56 Givi trunk, like the luggage rack or back-rest, please let us know how the install goes and maybe make a video. Thank you again.
@danielpalmberg3371 Жыл бұрын
A bit late maybe, but I would try to use the old punched out cover, turn it upside down and glue/silicone it back over the hole from the inside of the topbox thet hasn't the brakelights. I think that would make it water tight even if you take the box off the bike. Thank you for posting - nice vid!
@bubbles1863 Жыл бұрын
Thank you very much i couldn't understand the instructions 😀
@jamestinson9069 Жыл бұрын
Great video
@370H55V7 ай бұрын
As nice as being seen with more lights is i can only expect with these pin touch conections that something will eventually fail and the brake light will stip working.
@robby7503 жыл бұрын
Good job! I enjoyed the video.
@vicente83543 жыл бұрын
Very nice, thank you...
@crashman66723 жыл бұрын
Good video It helped me decide to get one for my case
@2024loop3 жыл бұрын
Crazy such an expensive case dosnt have that 2 usd led allready fittet -
@garykeighley7123 жыл бұрын
Great video and very helpful 👍
@MrEvanspa Жыл бұрын
Is it brake light only? Or does it give turn signals too?
@bubba5536 Жыл бұрын
Brake light only unfortunately.
@marekwojdak77584 жыл бұрын
Cool !
@TI23TMM Жыл бұрын
Bonjour, et merci pour vos vidéos. C’est seulement des feux stop ou il y a aussi les feux de route ? Merci
@PCG20223 жыл бұрын
Great video👍 I don't have the monokey rear plate. I have the Suzuki rack with the monokey junction kit. What size is the whole in the rear plate? In mm would be great so I know what size whole to drill out. Thanks PCG.
@stefanopezone71662 жыл бұрын
buongiorno ho montato su bauletto givi v56 e ci sono riuscito pero ho notato quando freno si accende insieme faro posteriore per il problema che quando accendo i fari anteriore non si accende sul bauletto ma faro stop si dove ho sbagliato il mio scooter kimco xciting 300r 2011 aiutami a risolvere grazie !!!
@nyannyanmoto79632 жыл бұрын
What does that break light kit called? And where did you buy those? Is it also from givi?
@croutonsinasalad54932 жыл бұрын
Yes, the light kit was from Givi. This is the part I ordered, although it appears to be out of stock now. www.revzilla.com/motorcycle/givi-e160-led-brake-light-kit-for-v56-top-cases?sku_id=1120978
@abolatius3 жыл бұрын
Danke sehr.
@mevagisseymedic3 жыл бұрын
Would it not have been easier to drill a hole?
@freerider70643 жыл бұрын
I've located my power and brake wire, spliced in but no power to box. Any suggestions?
@croutonsinasalad54933 жыл бұрын
I would look to see where you have good power from the brake lighting circuit then work my way backwards with a circuit tester until I found the problem. I'd also verify that you're on the brake lighting circuit and the ignition is on.