GM Bypass Ignition System Operation (part 1)

Part 2 • GM 3300 Intermittent n...
This is a unique design when it comes to ignition systems. One where the ignition module can control spark completely independent from the engine computer and is something GM used for many years. Starting with their computer controlled distributor ignition systems in the early 80s and continuing in many different waste spark designs well into the late 90s.
The engine being discussed is an older GM 3300 but the material can be applied to all GM bypass ignition systems.
This lecture was given to my class in connection with the following case study:
GM 3300 Intermittent no start rough idle (shorted injectors)
• GM 3300 Intermittent n...
Related videos
How to test a GM ignition module (crank sensor bypass test) - VRS • How to test a GM ignit...
ScannerDanner gets his butt kicked by an '88 F-150 (EEC-IV Ignition) • 1988 Ford F150 EEC-IV ...
Topics discussed
How a bad ignition module can cause a no injector pulse condition with good spark.
How electronic spark timing works
What is the difference between "Module mode" and "EST mode"
what the "reference "wire is used for and why you want to remember the wire color
how to perform a bypass test on the reference circuit to check for injector pulse
Playlist
(Chapter 22) No Spark Troubleshooting, Ignition Coil & Module Testing • (Chapter 22) No Spark ...
For more information on this topic, I have written a “field manual” called Engine Performance Diagnostics which is available at www.scannerdanner.com as an eBook or paper book.
Want even more diagnostic training? Whether you are a DIY trying to fix your own car, someone looking to become an auto technician, or a current auto technician that wants to get more into diagnostics, subscribe to ScannerDanner Premium www.scannerdan... There is a 14 day free trial.
On ScannerDanner Premium I will bring you right into my classroom at Rosedale Technical College. You will find page for page lectures taken right from my book as well as exclusive classroom type case studies. What is so special about these classroom case studies? I pull live problem vehicles directly into my classroom and we troubleshoot them in real time, using and applying the theory and testing procedures we learn during the classroom lectures. There is no better on-line training of how to troubleshoot automotive electrical and electronics systems anywhere!
Disclaimer:
Due to factors beyond the control of ScannerDanner LLC, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ScannerDanner LLC assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ScannerDanner LLC recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ScannerDanner LLC, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ScannerDanner LLC.

[@spelunkerd]

Thanks for the very clear explanation. We need more guys like yourself, who understand scanning but aren't committed to one manufacturer.

[@wbfog]

Absolutely love the way you present information Paul. Even when I understand something very well, I have trouble explaining in easy to understand ways. Thought I was a pretty smart guy until I began teaching. Found out pretty quick how much I didn't know. Keep up the great teaching!

[@ScannerDanner]

For sure, being a teacher, you really have to learn the subject, more than you ever thought you needed to. Thank you!

[@tnamen1307]

@@ScannerDanner please make videos on how one touch auto up and auto down windows works on any car... Thanks in advance.

[@jacobnbr11]

I love the classroom videos. My better part of being an advanced engine performance guy was when I started using theory of operations and a labscope. Rosedale Tech should be so fortunate to have such a passionate instructor

[@shameelali2549]

The way the bypass system was explained was simply awesome. Thanx

[@ScannerDanner]

yep from the school of hard knocks :) (bad calls in the field) Also it helps to teach. You really think beyond the repair when you are teaching the subject. Of course reading articles, going to training classes, talking to other technicians all plays a part too. This will be 21 or 22 years of field work for me now, with 14 of them spent full time teaching, and I am far from knowing it all. In fact the more I learn, the more I learn I don't know. :)

[@SuperChefJared]

Absolutely fantastic video I think I learned more in the past few minutes than I have in the past couple years about cars

[@ozzstars_cars]

This video might be an 'oldie' but it is certainly a 'goodie'. It influenced me to open the factory service manual on my '93 Chevy Corvette 5.7L LT1 to see which ignition system it has (wiring diagram)..... it's a bypass type. Thanks for the inspiration to learn more about auto electronics Paul

[@jabawokidingdong1360]

WOW! I'm quite impressed and now more knowledgeable on ignitions than my mechanic and electrician skills use to be. You make me want to sign up for school now...

[@ScannerDanner]

I have an online class on my website if you're interested www.scannerdanner.com

[@tnamen1307]

@@ScannerDanner sir, let's take an example about ckp sensor. 1. The car starts well, everything ok. Now, while engine is still RUNNING, if the ckp sensor is unplugged or removed, will the engine stall?? 2. I removed the ckp sensor and had someone to crank the engine at the same time, I'm creating blocking and unblocking the magnetic sensor quickly with metals fast enough to send signals to the ECM. At this manually signal inputs to the sensor, will the engine CRANKS AND RUNS??

[@ScannerDanner]

@@tnamen1307 1. depends on the car and the design of the cam sensor signal, in general almost all of the older cars will immediately stall 2. nope, the crank sensor is timed mechanically to piston position (top dead center of a cylinder) and you will never be able to match the correct timing signal by doing that

[@JonOffgrid]

@@ScannerDanner hi there sir i been working on cars along time i pick up a 95 Camaro 3.4 it has spark but no injection pulse i put a new fuel pump and new gas tank do yea any ideas on how to fix it i have gone broke trying to get it going

[@ScannerDanner]

@@JonOffgrid do you have fuel pressure? Any trouble codes? Is this a sequential injection system or a group fired system? Can't remember. If it is group fired like the 2.8 and 3.1 of this era, one single shorted injector can cause this

[@bahibrahima1480]

Paul you are the legend of diagnostic electronics vehicles. I like the way you teach.

[@brakedd]

Saw this after watching your 2.2 S10 video. I didn't know about bypass ignition systems until today...thanks ScannerDanner!

[@ScannerDanner]

@fivefortyeye540i Yes they will. Also keep watching, I plan on doing more ignition system design type stuff. Also thank you for the compliment! I really wasn't sure if this type of video would work well or not.

[@halleffect1]

Excellent explanation. I never made the association between GM and Ford EST/SPOUT. This really clarifies it. thanks

[@nickayivor8432]

Good Evening ScannerDanner 🙏 ✨ Have a great day, take care ScannerDanner,God bless you 🙏 Great tutorial thank you 👍 Nick Ayivor from London England UK 🇬🇧

[@ScannerDanner]

@trad444 Thanks for the book purchase and comment! The CKP variation learn is for crankshaft acceleration rates (frequency increases) for each cylinder firing event. I believe this CKP learn is for proper misfire monitoring to take place, not for the 1x and 3x signals, as this is only one of hundreds of designs.

[@TrickyMickTrucking]

Thank You. Been dealing with an intermittent no start on an 01 Blazer that is a complete no start now unless using ether(starts EVERY time). This is a big start in solving it. New fuel pump, plugs this past summer. I'll be checking this asap.

[@bigairnohander]

That was the most distilled and concise explanation I've heard, describing construction and function of a bypass system. You young techs need to pick up Paul's book. I have been in the trade for 31 years, and grew up in the business prior to that. I Just purchased the book myself... I could have made a lot more money if material like this was available back when I started out. Thanks Paul, you are a good ambassador for our trade. I Haven't seen any gdi or multiplex? Got vids?

[@ScannerDannerPremium]

Thanks bro! Would you mind providing some feedback here? www.scannerdanner.com/feedback#add-comment As for GDI, I have some stuff on my premium channel but nothing in print yet. Thank you!

[@bigairnohander]

I really like the way you are able to un-pack your topical info...and I believe your viewers would greatly benefit from you taking a moment to review construction and function of the component you're field testing. i.e. looking at spark on a waste spark coil....many techs don't know what that is. It's just a quick reinforcement. I've seen you use reinforcement in class, and it would be good to see in your field work. I will be happy to provide a review of your book; I will be joining your premium channel once I have pre-read your book materials completely. Have a great weekend.

[@mikeanderson1994]

ScannerDanner Premium i have the bypass wire the tan and black wire cut and the car runs but not that good it wont run over 120 km could it be from the bypass wire do i need to fix it or is it ok to leave it cut ? thanks man love ur videos by the way ur the best

[@jordankahele14]

The design Paul described and explained in its natural settings was to perfection

[@leeii9779]

Well described. I had a really good bite on this before the video. I'm now 100% on board! Thank you!

[@mechanuts7191]

This video just suggested one of mine for ESC. I was kinda proud,lol.

[@mechanuts7191]

Wow, Cool you pinned that. Now that I know you are paying attention let me say thank you. I've used you as a reference point to go back to whenever I get ahead of myself on something. It's good to solve problems when you are working. Like mental exercise

[@Thor7167]

Very good video, explaines ignition system input and output signals in a very easy to understand format. Paul Danner for President!!!!

[@ScannerDanner]

@felmar39 Thank you for your purchase and comment! I am glad you find the information in my book useful.

[@timthemechanix]

Hey Man, good video. I've wrenching for a lot years and you just made my day. I mean I've been doing this for 40 plus years - but usually hard way compared to yours. Actually been watching your channel awhile. Been supporting myself pretty well wrenching for myself 17 years near Denver. Anyway, caught this one right on time. My neighbor moving on after 30 years in the house gave me a '89 Pontiac 6000 STE (AWD) in go condition except busted 3100. he'd pulled a 3100 supposedly from a '93 said was running, but what I saw was later OBDII. My good friend Brien - great dude - is dying from cancer, talks through a hole in his throat and never smoked. Doesn't have long. He's driving this worn out Envoy thats junk. (Actually trying to get the security to relearn a key and he using my truck for his medical stuff) Brien likes this car. So it;s over here. He dropped the subframe w/powerchain. I switched out the engine, everything bolts up. Also, was told is was pulled from a Pontiac but one different mount. Was side by side comparison to a 99 Buick Century perfect match. We'll have to modify the fuel lines and egr, then figure out how to wire it in, its electronic without a vacuum line, and heater hose routing. The guy brother had scrapped the 89 intake and throttle body, but saved the injector harness and it plugs into 99 injectors. All 6 have same color code and I could only guess the routing. It has 2 crank sensors, one to the coil pack match. extra one at harmonic. Also, cam sensor. Same coil pack just different location. Engine is in, it's back on the ground, just trying to find time/money to finish. Probably fire is up in a few days. But this kinda matches this vid and had to say thanks. And again for your scanner stuff. I mean I used a solus pro for years and now I have a modis edge. Trying to learn everything. I'm learning the low amp probe, secondary coil stuff. I have a little website that I have back up after being down 5 years. Going to link this video there, probably on Tim's Build's button. www.timthemechanic.com/ Thanks Again for all your vids.

[@ScannerDanner]

@chetsjug You need to watch Part 2, sorry I didn't label it that way. Here is the name of the video "1991 Buick Century 3300 Shorted Injectors" this is what was wrong with this car and it sounds like this could be your problem.

[@ScannerDanner]

@scraiga66 I don't have a video on that but check out the wiring diagram on a 1993 Chevy Cavalier 2.2 (VIN 4) engine compared to a 1994 Chevy Cavalier 2.2 (VIN 4). The 93 version is a bypass system (CKP sensor goes to ICM) and the 94 is completely ECM controlled (CKP sensor goes to ECM). So for no spark diagnosis we need to treat these systems differently. Thanks for the comment

[@vader2492]

Thanks for your videos, i purchased the book several days ago and have been watching your videos. You are a talented instructor and your students are lucky to have you. We need as many well trained techs as possible in our changing industry. There are too many hacks out there armed with a $40 code reader giving real working techs a bad name. Cars are not the same as in the 60s and 70s. Consumers should watch some of your vids and see what actually goes into a proper diagnosis

[@ScannerDanner]

I have seen a completely plugged exhaust cause that. Also a bad coolant sensor which was causing as immediate flooded condition. Also I have seen these early design injectors only short out when under "stress" and test fine with an ohmmeter

[@NeeKroVal]

this was the best class i've ever taken

[@mattboswell8656]

Man I've been looking for this video for 3 hrs. Thanks man needed a standard ignition breakdown. Awesome job!

[@Pef273]

I was looking for something different when I came across this video. You produced a really great instructional video!

[@ScannerDanner]

+Pef273 thank you!

[@danb.3397]

This has been quite helpful with my 1993 chevy 7.4L system. My bypass wire does not read in volts but millivolts so I'm hot on the trail ! My truck will start quickly but idle kind of rough with the bypass connected and smooth with it not.

[@GEARHEADSOLUTIONSES]

Really thanks from Spain. Now I can understand the GM ignition and my Vette 87 problem. Very very good video. Congratulations

[@ScannerDanner]

+GEARHEADSOLUTIONS.ES sweet!

[@ScannerDanner]

Lol, I've just been doing this for a long time. I really not that smart. Thanks for the comment

[@ScannerDanner]

It takes me awhile to start in the morning without my coffee :-) just kidding I need to know a little more about what your working on to help.

[@ScannerDanner]

When it doesn't start see if you are getting a reference pulse on the purple/white wire coming out of the distributor connector. IT should be a 5v square wave pattern.

[@jacklong311]

Very good information. Thank you for the explanation. Presentation is top notch.

[@nickayivor8432]

SUBSTANTIAL Sir ScannerDanner Tutorial great ❤ it thank you 👍 👏 👌 God bless you and all your family around you Sir ScannerDanner Sir ScannerDanner From Nick Ayivor from London England UK 🇬🇧

[@SteveXNYC]

First let me say thank you and God bless you for you education and help have you provide. I will be very grateful for you answer. The question is pertaining to the information provide in this email. I will like to know if, the GM 3.4 V6 Ignition Control Module can fire its Coils without the ECM/PCM signal and the fuel injectors remain in functioning order with spraying fuel?. I car understand these two signal are LO and HI 3X reference signal. If the ICM need this signal to fire the coils, where can the circuit get the LO/HI 3X reference signal from? Can it be gain from the LO 3X signal on the crankshaft sensor reference signal and the HI 3X reference signal come from the camshaft sensor?. Thank you Sir

[@ScannerDanner]

What determines this (bypass system or not) is where do the crank sensor wires go? If they go to the ICM first, then it is a bypass system and spark is controlled by the ICM directly during cranking. If the crank sensor wires go directly to the ECM first, then the ECM is always controlling spark. Make sense?

[@quangnhatnguyen1172]

I don't know how this channel is less than 1 million subcribes! Good job my master!

[@ScannerDanner]

I haven't forgotten about you. I just need to look at this diagram a little more when I have more time. This is a weird design

[@philipar6787]

Thank you Paul 😊 Hope you and your beautiful family are doing well in these times Have a very Merry Christmas 🎄 and a happy New coming year your a Great Teacher

[@ScannerDanner]

you can still have spark on this design with ECM problems. If it is a no start with good spark, the next step would be to check injector pulse. If no pulse you can still have a bad module even though you have spark. If the ICM is sending an RPM signal to the ECM then you have an ECM problem

[@shadowoutlaw9834]

most times the VAT security system known to crank engine key must be read through the ignition switch sensor that sends the key code to the BCM from BCM to the PCM/ECm tells the injectors and fuel pump and electrical volts to the coils to kick on and start . the ingnitions in GM with computer those pass key ingnitions on most gm known for going bad they sensors get fried out or drop below true voltage signal. i just replaced a ingition switch after the chevy dealership said they could not get it to read on there big Computer that there was no comunications obd with BCM and the PCM/ECM they had 5 of there best Machanics working on it for a month, tore it all apart and they still could not figure it out. this car belongs to a friend of mine, so he got it towed back to his house. i went over there changed out a relay and got my scanner to work reading the obdII system i did a full modules scan and got codes, so next i dug into some researching on these 2001 to 2005 gm vehichles and little do you know, they have had bad issues with the ingnition switches 8 recalls on gm electrical stuff on them. well on the chevy impalas 8 recalls . 5 on the chevy silverados anyways they all have the same Passlock sensor ingnition switches security ingnition lock sensor. make a long story short i got another ingnition switch from a junk yard for 50.00 bucks with 2 keys to it like brand new. placed it in plug in all wire connectors and shifting cable in , and did the relearn key in ingnition procedures steps and walla 4th time started right up. easy peacy. just thought i shared that with ya or for anyone that has had issues trying to figure out why there gm vehicle wont start no crank just clicking.

[@fivefortyeye540i]

Scannerdanner, will a data base such as Alldata, Mitch tell u what type of ignition system u are dealing with? After watching ur vids I find that I dont know a 1/4 of the stuff I thought I knew. This is the first vid I've seen that shows systematically how it works the sequence in-which what component relays signal to next component to get the system up and running. Very easy for the brain to digest. Excellent 5 stars Scannerdanner !!

[@pedrogonzalezromero7346]

Excelente tema Excelente explicación Tecnica.. Son pocos las personas que trabajan este tipo de información por este medio, con explicaciones de circuitos que nadie describe, y si lo conocen, lo hacen y explican de manera muy superficial, seria muy interesante relacionar este sistema de encendido en Derivación Chevrolet, especificamente en los Impalas 2000 al 2005 motores 3.8 , ya que presentan demasiados problemas con su sistema de ignición y el sistema anti robo ó Passlock.. mucho se le agradeceria si lo hace de la forma tan magistral como explica en esta Clase de este Video

[@ScannerDanner]

after looking at the diagram. I don't think it can be done. you cannot interrupt ICM power or ground, you will lose your input to the PCM for injection. The only option is the EST line you mentioned but I think the ICM will still fire the coils in "module mode" with an EST line fault. If the coils where not mounted on top of the ICM it would be a different story.

[@ScannerDanner]

Mitchell On-Demand, best diagrams for us aftermarket guys!!!

[@hddm3]

wow i wish i knew just a 1oth what this guy knows. I hope you keep puting these vids up. Im getting smarter by the vid. Thanks, going to buy your book for sure.

[@ScannerDanner]

lol, never heard of that. don't mess with the EST line, you'll just set a DTC. The module will still control spark without the EST signal. what is your ignition set up? is it a waste spark? or is this a distributor engine?

[@ScannerDanner]

@vader2492 Thank you very much. That was a great compliment. It is true what you say about consumers needing educated on why they need to pay for diagnostic time. Most of them think all you need to do is plug in the "computer thing" and it will tell you what to fix. The "free diagnostics" that the parts stores offer hasn't helped this train of thought either.

[@abderrahimmark]

That's rocket science to me. I am grateful I am specializing in Diesels.

[@Altermyego-]

Damn you Paul why do you have to be so freaking through! Always got to do everything right...

[@ScannerDanner]

check compression next. if you have spark and it will not start with a fuel source then compression is next. these are known for timing gear issues i believe.

[@ScannerDanner]

Get the engine warm and tap on the crank sensor with a long screwdriver. Be careful of the serpentine belt and crank pully. If the engine stalls then you need a crank sensor. As for testing it, I actually have a 3800 crank sensor video that I haven't uploaded yet. I'll try to get that up soon.

[@felplayvina]

Hi Paul I have question 95 ram 2500 v10 no spark. this PCM need Crank and Cam sensor for spark, so PCM to ICM to coil. so should I have 2 pulse from PCM to ICM?.. From PCM have two Ignition Module wires to ICM key on 5V,, Cranking only one pulse the another drop to 0V..

[@scraiga66]

Got an example of a GM with ICM that the CKP runs to the PCM? Not the misfire crank sensor. Love your stuff by the way.

[@cowsauce9099]

This video is really improving my understanding. Although I was a physics major and understand a ton about wiring, it's hard to find good information on older automotive systems. Any recommendations? Also where do you instruct at?

[@jimmyjordan435]

excellent work by the Master, i like to know about other system where the crank sensor is directly wiried to the pcm however the cam sensor is wired into the icm

[@ScannerDanner]

@Mark1944089 it's called a multi function switch. the steering wheel have to come off. and if it is a tilt wheel system these can be tricky. the new harness gets fed down the steering column on the inside. not a real fun job

[@MrJgonzalez2]

Paul, on thie design is it possible to have spark during cranking and to have something wrong with the ecm and still have a no spark no start? Is it common?

[@ScannerDanner]

You most likely have shorted injectors. Watch my videos on GM shorted injectors. I have three of them up. A quick test for this is to unplug your injectors one at a time and see if the car starts. IF it does then you found your problem. Keep in mind though that you may have more than one injector shorted. In fact the last vette I did had 5 out of 8 injectors shorted.

[@williamfigueroa9838]

I like you profecional explanations videos , God bless you.

[@stevenmaxwell1506]

Interesting video is a 86 corvette part of this system it starts but won't run lots of cut rewired and jumped wires from previous owners

[@matthew53690]

Paul do you have a link to the case study you did where the work van had a viper alarm system short causing no inj pulse? I swear I saw the video before but can't find it.

[@keshwin108]

Good talk. I'm assuming that the bypass function is to make the engine start quicker because the Ecu takes a few revolutions to initiate the spark because it has to Calc the rpm and thus the engine rotates a few times more before starting. Am I correct in my thinking?

[@romanciano7040]

Hello I am new in the industry and building my tool set. Do you or your organization offer any sort of scholarship or grants to people like me just beginning in this field? I am interested in buying some basic diagnostic tools and maybe a scope

[@oliverschulze3926]

I have a question, you have 4 cable, which cable should be connected to create a bypass. Red/blk and white

[@soupflood]

What voltage range does the computer send to the ICM through the WHT wire once it has been bypassed with the 5V through the TAN-BLK wire?

[@todayintheshopbanksy5904]

Hi Paul, what is the point of firing the coil from the CKP if the ECU / Injectors are not at the party. Is this to clear out the cylinders of residue or something during crank? regards Mike

[@felmar39]

Very good video and by the way .I did get your ebook and is very good , thank you so much for sharing your experience with us, good bless you my friend

[@ScannerDanner]

no fuel test port on the 2.2 engine. you have to t-in after the fuel filter under the car. it sucks

[@ScannerDanner]

No problem, and thank you

[@jasonneal3917]

I have a 1986 C10 rear wheel drive 5.7 350 and It has been running good until yesterday and then it quit running while running down the street. Now it won't start at all. It has what looks to be a new mechanical fuel pump, it has a good battery , new alternator and new starter. The question is what could it possibly be. I was told that it could be the ignition computer inside the cab of the truck behind the glove compartment.

[@ario1139]

Just found your link, I have a 1999 Chevy 454 Vector 7400 V8 7.4 L installed on a workhorse chassis- class A motor home. I have a no crank no start, I replace the starter and I have crank, but no constant spark, I replace the crank positioning sensor and it spark and then stop. so I have crank some time spark, ICM or ECM?

[@khaniftikhar9225]

Nice demo

[@redsson6669]

hey paul if you were to do a by-pass test with a ''FUSED'' jumper wire and lets say we put a low amp fuse in the jumper like a 3 or 5 amp fuse, if you got the polarity wrong would you still cook the driver, or would the fuse blow and save the circuit??

[@salcast1276]

hey paul so on this this dising is it possible to have 170 psi of compression on all cylinder, 45psi of fuel presure key on egn off, and 37psi egn crancking, have injector pulse, and spark on coils, have no shorts on any of the injectors 12.5 of homs on each one, have cmp and crank signal, and still have a no start? i had one like that few years ago it was 1994 buick century customer replace pcm, icm, cmps, ckps, he brought it to out our shop to see if we figure it out but no luck.

[@ScannerDanner]

you need to find out what your missing when it dies. spark or fuel? then maybe i can help. my eBook would be very helpful for you in learning testing methods too.

[@memphisbankhead]

I'm getting a electric spark timing is grounded code 42 .. do you know what this could be .. i have changed the optispark, coil, ignition module, air flow mass sensor, and pcm .. working on a 95 caprice. Any suggestions?

[@razojl83]

Excellent video. great job

[@ScannerDanner]

Thank you!

[@sivucit]

HI, Where do u get such diagram, when i see All data i dont see such good diagram, do you get it from manufacturer or mitchell. please advies

[@marktirabassi7873]

You mentioned that using bidirectional control, you can fire 🔥 a Chrysler computer. How on the scanner would you do that ?

[@cj7girl280]

Interesting... So... I have a 1976 cj7 jeep with 258 engine and recently installed a gm 4.3l rebuilt tbi unit with ecm on it.. It starts and runs but has check engine light on.. Shows codes 42 and 43... These are for the spark control, which I haven't installed.. What is the best way and most economical to install in a upgraded ignition system in a cj7 jeep that the gm ecm will be able to control the timing? (the throttle body is for gm models 1987-1991 with 4.3l v6) :) by the way, I have the bypass GM system

[@grubasgarage7854]

great video, where can I get this diagram that you are using ?

[@ScannerDanner]

Here is a DIY version of what I use eautorepair.adtrk.biz/?a=10817&c=24&p=r&s1= You can pay for access to a single car, for a month, for $20

[@jacshop6683]

Got a question on that bypass system got no spark got no fuel it's a 1995 Chevrolet but I've got no spark if I unplug the bypass under the dash if I have a bad ICM can it cause it not to have spark. And it has no fuel control either nor spark control

[@randy1ization]

how does it work on gm vehicles with no crank sensor or cam sensor. does the timing connector on the firewall disconnect the computer and just reply on the ignition module for starting and running?

[@chetsjug]

Wow! Got a '93 3300 that *always starts*, "turn key"instant stalls,from 1-30 seconds on average. yesterday it ran for 15 minutes twice!.. then stalled when I tried a test drive. I've ruled out fuel by fully testing, all is textbook pressures. It started 3 months ago, on warm engine after a load like going up a freeway on ramp. the next weeks, it settled into a shut down at any speed, throttle position, temp. Have new ICM,CPS,fuel relay. Now I'm lookin for a broken wire... any thoughts?

[@geryscole4055]

Great vid! Do you have anything on bypassing / troubleshooting PATs on Ford Mondeo (Ford)?

[@fivefortyeye540i]

@scannerdanner man I know this may seam like a crazy question.. How?? How dose one become detailed on system design and how it works as if he designed it himself.. I know Mitch gives a generic description.. Do u get info from other places and put the puzzle together???

[@carlfisher7688]

question I kinda feel bum asking but im a ase tec and feel a bit lost 95 buick lesabor with a 3.8 cranks up on start up but looses injection pulse ,new fuel pump and crank sensor I did love to see how you explained this video

[@ScannerDannerPremium]

monitor the purple white reference wire coming from the ICM. see if you are losing that signal, if you are you may have an ICM issue

[@danieldonttrip9253]

My old distributor has a ECM connection however I replaced it with a new one and there is no ECM connection . So the question is what do i do with the ecm wire that connects to the distributor

[@brakedd]

Are bypass systems like this universal across the board with GM products?

[@ScannerDanner]

a fuse jumper wire will not protect the driver. relay drivers only carry 100 ma. and even hi current solenods only carry around 1 a.m. of current flow.

[@dripsquad2524]

I have a buick rendez-vous 04 3.4liter v6 cylinder 1& 5 misfire needs some help pls!

[@roballen5670]

Have you ever came across having to swap distributor when changing engine due to the new engine not having a crank sensor? I have a 95 Blazer and yhe old engine had crank sensor. Tbe replacement engine doesn't. Please help. I swapped the heads and CPI already to the new engine.

[@altlandf]

The only sensor I didn't replace is TPS. I have a cardone select distributor. NEW. My 89 s10 pickup throws a code 25 even though I replaced the IAT. I have a harbor freight timing light. Timing mark moves back and fourth a couple degee and engine idles fine. It's when you drive the engine holds back. When it reaches operating temps the engine wants to stall when coming to a stop. Can the red brick force the truck to run right. Is that a bidirectional scanner?

[@ScannerDanner]

disconnect the EGR vacuum hose and drive it, see what it does. My guess is your EGR is sticking open, causing the rough idle and almost stall. This will also heat the intake to a point of setting an IAT code

[@shadowoutlaw9834]

could be a Fuel Pump going weak/ to Bad .check your fuel pressure and Fuel Filters might be plugging up.

[@gregorysinclair6133]

LIKE THE VIDEO BUT WOULD LIKE TOO KNOW ABOUT THE CAR RUNS FOR ABOUT B10-20 MINS THEN CUTS OFF AND WILL NOT START BACK HAVE TO LT IS SIT FOR ABOUT 30 MINS THEN IT WILL DRIVE FOR ABOUT 29 MINS AND DO THE OVER AND OVER SO I WOULD LIKE TO NOW WHAT IS THAT PROBLEM

[@codywichman213]

on this bypass ignition system what would happen if you lost the sync signal but still had rpm signal. would it long crank and start or complete no start?

[@Beards88]

I got a 98 Deville same concept but a V8 how would I keep my injectors going but shut off ignition by a push button switch? Would it be the EST wire? Its for my flame thrower kit. Its not working by killing the 12v to the ICM because the pcm is stopping the injectors.

[@devilswish8876]

I have problem here my gm starter selenoid has R terminal and I want to use it to help my start in winter but aperantly my positive linear dashboard regulator dont alove it ore I did some thing wrong because my dash fuse poped, I have singel hei coil E core type my distributor has a induction triger and the gm 4 pin ignition module is inside the delco distributor as well how can I solve this problem? Reversing the conections on the starter selenoid? ore atach in other place ore terminal on the ignition coio it self? Any way are dc boost converters ore amplifiers a good choise instead? I wuld like to also build oil cooling contained for my ignition coil those hei coils are nice they can take good punch but the wiering confuse my I have a old Opel Monza 82 model the wiering is prity shity in that thing evry thing goes on 1 wire so Im cinde of in big problem when winter comes

[@lam5102]

I have a 93 gm Buick 3.8 intermitted no start/spark j think is the crank sensor what wire I need to check?

[@randy1ization]

so if the plugs have fire and the fuel pump whirrs but doesnt pulse the injectors in the throttle body what should we do next

[@Headshothorror4488]

Help I want to be a mechanic and go to school... I dont understand a word u say, does this mean I can't do it or is this a waaay advanced class ? Do classes start from very beginning about cars and engines ect or must you already know allot ?

[@ScannerDanner]

+Headshothorror4488 This class would be taken after having an 8 week course on engines, then another 8 week course on basic electrical. So my engine performance class is more advanced but not to the point where you can't follow along. All of my students are just as "green" as you are my friend. Let me know if you want more information about our school (Rosedale Tech. ) and I'll get you in touch with one of my friends in the admissions department. Thanks! Paul

[@UBBERTANKER]

if you were do do that while cranking it would fire correct?