Golf6 Cluster Swap With VVDI2

This Is How To swap And Program A New (Used) Instrument Cluster For A Volkswagen golf6 ... Reading Immo Data From Old Then Write To New
... Using VVDI2 and VVDI Prog ... Tried Pogo Pin And Eeprom Service Mode ... On Pogo Pin Method I Think Didn't Work Because Didn't Get Brake Light Only To Blink But
i'm Not Sure May Be It Worked But The Wrong Identification Of Cluster Type didn't Let Me To Continue ... Also Service Eeprom Leaded To Non Standard Login Failed ...
Finally I Found That It Should Be Nec+24c64 ... And Not Sure And Don't Know If I Choose That From The Begining

[@hotice3181]

Hi THank you for video I have no VVDI2 but the best tool and faster tool for this is Original Car Prog On Line The whole proces cloning dashes lasts 20 minutes and you do not need to program key as well

[@heshamessam8042]

You are welcome

[@waldemarfechtel1644]

In vvdi2 is service mode option is shows you need read eprom first and whrite back in dash. First need to whrite original eprom by obd back to dash. After this you can read the immo data and as last step whrite old(orig immo data) back to it. This it. When make this on car, first safe abs coding (very important)

[@docteurdahmani]

Good job

[@heshamessam8042]

Thanks

[@khalilaymen8882]

برك الله فيك ❤❤❤

[@heshamessam8042]

الله يبارك فيك

[@aleksandrogienko3371]

Super

[@heshamessam8042]

Thanks

[@ahmedmohmed-dw4jv]

الله ينور ياهندسه قلب الدنيا ع رقم حاضرتك ومش عارف اوصل لحضرتك 😂

[@heshamessam8042]

🙂دا نورك ... 01005387513

[@jcruz2010]

Ok so if you have the key just need to copy and paste the datas no open the cluster to do all that extra steps?

[@heshamessam8042]

Won't access data till open

[@alexang1054]

Hi, im doing the same cluster swap and im having a keyless go key. Steps that i do 1. Read old cluster eeprom using vvdi prog and prepare service mode using vvdi2 then enter and read immo data. Copied immo data in text file. Write back non-service mode dump and reset cluster steps are taken. 2. Read new (used) cluster eeprom and prepare service mode. Read immodata and modified vin, cs, mac, key, pin, status, config. i couldn't modify power class. Write back non-service mode dump and reset cluster steps are taken. 3. Am i missing some steps here? I couldn't get the car switch on ignition and started. Immobilizer active is written on dash. Can you please help me on this?

[@heshamessam8042]

Read immo data from old (don't know why servicemode as u have a working key ).. write to new (will need service mode to access immo ) ... also read vvdi2 manual as someone one told me in comments

[@abhiautotech1031]

At last how it was done? Could you pls explain the end process.

[@heshamessam8042]

To much tries ... at different identification ... it was identified wrongly at first

[@technewsl8190]

i think its easier to do the whole work with VVDI PROG .. right ? read the files and write in new module with VVDI PROG

[@heshamessam8042]

Vvdi prog will not read immo data

[@MohammedAli-mz2vl]

Salam what r the cables u use on the cluter to get light. Thank u

[@heshamessam8042]

Original cluster connector

[@lostkey5927]

Where can I get cluster photos?

[@heshamessam8042]

Pogo photos ... i downloaded it and don't remember

[@mpfact1]

You was on the wrong pogo point I had the same problem the diagram you used is wrong thats why you did'nt get the brake light only

[@heshamessam8042]

thanks ... could you share the right one

[@solarsolari6705]

what about just exchanging the chips on the board?

[@heshamessam8042]

Which chip ? Eeprom ? Immo data is on eeprom and processor as i think

[@solarsolari6705]

@@heshamessam8042 I don't know exactly, but I think it's on the processor.

[@heshamessam8042]

@@solarsolari6705 and also eeprom... so what will you exchange? ... both ? Will need sane hardware and very hard to do

[@solarsolari6705]

@@heshamessam8042 Why both?! Isnt the Mileage on the one of them only? If the doner cluster is exactly same model do we still need hardware ? I thought just swapping the chip it works

[@heshamessam8042]

@@solarsolari6705 swapping chip as i know will not work ... hardware is same if part is same not neccessarily the model ... anyway reading and writing the data is the best way at least on my opinion and that what i do

[@georgh8537]

Try with fvdi

[@heshamessam8042]

At the end .. all done successfully qith vvdi2

[@waldemarfechtel1644]

Next time read the manual more as once!!!! It whrite for you, fist whrite ori eprom by obd back to dash

[@heshamessam8042]

Excellent thank you so much i will read that

[@najibcheddad4099]

السلام عليكم اخي الكريم ارجو منك مساعدة اذا امكن عندي vvdi2 احاول قرائة cluster pq لكنه يعطيني هاته الرسالة non standard upload data failed

[@najibcheddad4099]

في mqb يعمل جيدا لكنه في pq لا يقرأ immo dat شكرا على المساعدة اخي

[@waldemarfechtel1644]

@@najibcheddad4099 I can't understand, English would be nice

[@heshamessam8042]

اي هو ال pq؟ مش فاهم