VW VAG CAN commander read and write eeprom modify instrument cluster VW Golf 4/VW Passat B5
Пікірлер: 20
@barlogdark2 жыл бұрын
Is it possible to code needle sweep to Passat B6 2007 and to resd immo code?
@bebeadi4866 Жыл бұрын
On Audi A3 8PA model facelift year 08.2008 works?
@thered33402 жыл бұрын
Where can you download this dashdumpedit program?
@euphoroian3 жыл бұрын
Can i remove the flashing yellow oil level lamp with this? I dont have an option in vag com(vw polo 9n3 2008). Thank you!
@unmountablebootvolume3 жыл бұрын
Why in the world would you want to remove you oil pressure light?!?
@euphoroian3 жыл бұрын
@@unmountablebootvolume it's not the oil pressure light. This sensor of the car to let you know that the oil it's at low level or the quality its poor. Some cars come fitted with this sensor, some don't, mine came without but i still have the Yelllow (not red) flashing oil sensor in the cluster.
@unmountablebootvolume3 жыл бұрын
@@euphoroian OK, that makes more sense. I remember they had something similar on the sharan, where it would beep and say "check oil level" if the hood wasn't opened for a while, which could also be caused by a failed hood switch (or it having a bad ground connection or having been removed/disconnected as part of an alarm disable). I would check the wiring diagram for where the hood switch signal goes, and measure right at the ECU plug. It should short to ground if the hood is in one position (i don't remember if it's open or closed), and should be close to or more than 3.3v (the lowest logic voltage commonly found on an ECU) in the other position.
@euphoroian3 жыл бұрын
@@unmountablebootvolume i will definitely check. Thank you.
@TheEntryHD2 жыл бұрын
Hi Can you send me this software? I can't find a working one.
@ovidica672 жыл бұрын
Hello. What wiring diagram between the OBD connector, the blue connector, and the green connector you used to work on the cluster table? Thanks.
@golfwagen41732 жыл бұрын
kzbin.info/www/bejne/fJDLh4WiZ56koKM
@veronicadiaz7359 Жыл бұрын
Hi can you send link to the sofware I can not find working one thanks
@OsmanGaziPasha2 жыл бұрын
Thank you
@baremats912 жыл бұрын
When Reading or writing mine i stuck on address 0x0718. Managed to read all epprom first time and saved it, but cant write IT back, it stops on address 0x0718
@thefamilibusiness3 жыл бұрын
Does this program work for BCM, module 09 central Electric?
@tzutzu. Жыл бұрын
Alcool need The software for 5.5 can comander my cd was empty
@glotze8636 Жыл бұрын
Hast du link zu dem Programm
@OOMT-SERVIS2 жыл бұрын
Comander mi pise Cannot connect to device octavia 2:/ nevim si uz rady
@martinratkos30552 жыл бұрын
Na golf 5 aky program pouzijem tento asi nie
@golfwagen41732 жыл бұрын
Neviem. Napriklad na starsie golfi 5 ci maju vdo budiky tak tam byi to mohlo ist. Na novsie co maju budiky visteon to prabdepodobne nejde.