Hey Gavin, just wanted to let everybody knows that the brugi fw is working. Resoldered my pitch connection but come to find out the motor was bad. Replaced motor now all is working. Thanks again for putting this tutorial out. CHEERS!!!
@shaybee2211 жыл бұрын
Nice and Thanks for posting instructions w/links, mine came with zero paperwork, nothing, just a box in an envelope with the gimbal inside. Very helpful! ^5's!
@Merq1mercury11 жыл бұрын
Thanks Gavin, will see and do the resoldering of pitch wires to proper leads.
@ozzelot198311 жыл бұрын
thank you for this Video - it really Looks pretty good. but as first time users without Manual inside the shipping, it is really tricky. thank you for your tipps here.
@HiMyNamesKyle11 жыл бұрын
On mine it's 2 wires with a 3 pin connector. That goes to the channel you want to use for tilt. I put mine on a 3 position switch, mid position holds it in one place and either side pans until you go back to center. It helps to change the switch speed down so that the camera pans slowly.
@yeogav11 жыл бұрын
I think the 3 pin connector you're talking about is for the Pitch motor override. Use a spare channel to alter the pitch of the camera in flight. You might have to move the wires to A1 (signal) and GND. You might not need to connect the 3rd wire (+5v) if you're using the same lipo to power the receiver and gimbal.
@thebarefootviking531511 жыл бұрын
Thanks for that, you are a saint! hopefully I can now get the gimbal to work! :)
@yeogav11 жыл бұрын
Hi there - yes using the motors that came with it. Will look up PIDs next time I have all my gear out
@yeogav11 жыл бұрын
No problem. Thanks for your comment! Yes it was a bit of a head ache for me too, working out how to set it up with no instructions with the gimbal. Cheers Gav
@Fishinstix11 жыл бұрын
Thanks for the instructions! Anybody else get it to work like Gavin?
@ncx9411 жыл бұрын
Hi, i had the same problem with one of my friend's gimbal. To solve it it's really easy, you just have to reflash the bootloader ;)
@CallintheGUNSHIP11 жыл бұрын
Nice video! I'm working through the install, it seems like a silly question but what do you plug the 3pin connector into?
@HiMyNamesKyle11 жыл бұрын
I followed the instructions you posted and it now holds the camera really solid and it's far smoother than my servo controlled gimbal. However, there is a high pitched humming noise, it isn't very loud but enough to be really annoying and concerning. I don't want to burn a motor out.
@theR0ck11 жыл бұрын
Gavin, you using stock gimbal motors from goodluckbuy or you replaced them? My board seems to be working fine but the tilt is really pitchy. Tried all possible combo PID still shaky. Can you list your tilt PID please. I appreciate it. Thanks for the very informative video and instructions.
@yeogav11 жыл бұрын
Motor will not burn out - you can change the motor frequency to stop that high pitch noise - can't remember where on the GUI you have to click though, sorry
@yeogav11 жыл бұрын
I had to desolder the Pitch control wires from my board because they appeared to be in the wrong place. I resolder the signal wire from the receiver channel used for camera pitch, to A1 and receiver GND to GND on the board (A1 & GND are marked on the edge of the gimbal controller board) hope that helps, matey
@yeogav11 жыл бұрын
Yeah it's not bad is it, for default settings. There is some oscillation if you slow the video playback down, but miles better than my old servo gimbal. :-) There is still loads of room for improvement on the setup and software side of things. All good fun I suppose :-/
@fdnyfish11 жыл бұрын
did your gimbal work using the defaults in the GUI? can you please post all tour stings from the GUI
@IdeologieUK11 жыл бұрын
Solid Gav!
@Soldier53flyer11 жыл бұрын
I want to buy one of the gimbals this looks good, I do not every good with programming will this take much time to make work right? and is this a stand alone gimbal? or do I have to run it off my F/C?
@yeogav11 жыл бұрын
Ok dude I added some instructions to the video description. Hope it is of some help. I lost some hair and a few years of my life trying to figure it out too.
@yeogav11 жыл бұрын
you're welcome!
@whitedime11 жыл бұрын
programming a brushless gimbal will consume your life. You will lose sight of your family and friends, you will lose your job, eventually become a brushless gimbal burnout and then, it's off to brushless gimbal rehab. Acceptance is the first step towards recovery.
@billwelch117711 жыл бұрын
Just got one of these. I'm embarrassed that I'm not up to speed on setup and no instructions. Got a few tips you can share?
@XRPgeneration11 жыл бұрын
I was thinking to buy one of these, but now...WAW....what a nightmare to install ! I'm not technical at that level. The video is nice though and just as nice as the videos with Zenmuse and others at 3 to 8 times the price. But I was hoping the GoodLuckBuy Gimbal was plug & play. Doesn't' seem to be the case !
@Vortexcinema67711 жыл бұрын
can u show me how to install on my battery there is no such input for it on the dji phantom battery
@HiMyNamesKyle11 жыл бұрын
I asked someone else and they said that noise is normal. I hope that's true.
@yeogav10 жыл бұрын
I have retyped in the instructions into the Video description - hope it is of some help.
@Lurkur11 жыл бұрын
Me too :) I don´t even know where to start!
@Merq1mercury11 жыл бұрын
Gavin, i succesfully reflashed my board as per ur instructions. But now my pitch is not working, not moving just stationary. Any suggestions? Got the V3 board from goodlucksell/buy. Thanks.
@Mato009211 жыл бұрын
Hello, I cannot see any instructions below. I got this gimbal but I have no idea how to make it work. Any help? Thanks. :)
@tdarican11 жыл бұрын
i had the same error. can you solve yours?
@QuadFlyerPilot11 жыл бұрын
Gavin, I'm thinking about buying the Phantom compatible gimbal discussed in this thread BUT when I try to link to the instruction link you provide under "Instructions Below", I repeatedly get an error message. Can you re-post the link?
@yeogav11 жыл бұрын
See instructions in the video description. Hope it's of some help!
@TheRevalak11 жыл бұрын
Hello Gavin!. I followed your instructions, but when in came to upload the Arduino file to the controller, Arduino said: "avrdude: stk500_getsync(): not in sync: resp=0x00" Can you tell me what to do against that? thank you -Revalak
@moremournemayhem10 жыл бұрын
anyone know where i could get a replacement gyro board for the bottom bracket?
@yeogav10 жыл бұрын
rctimer.com
@inteous9 жыл бұрын
Hey, so on my good luck buy gimbal (2 axis; roll, pitch) whenever i turn left or right (yaw) with my quadcopter the gimbal starts to roll in one direction but when i go back to the way i started its normal. anyone know how to fix?
@Lurkur11 жыл бұрын
I just got one like that, I´ve asked the seller for a manual and he said he would email it to me, so far nothing :( if you have any tips for me PLEASE help me! I will be forever grateful! :)
@Dizzypaint10 жыл бұрын
Hi, Anyone can send me manual how to plug in and start up this freakin gimbal? I got one without any manuals and after recieve my package no support from this little china sh*ts
@yeogav10 жыл бұрын
I've adeded instructions into the video description. Also links to discussion board where you can get help from the Multirotor community. You will lose hair and a couple of years off your life getting it to work for the first time, but it is possible.