Everything you need to know about the Piaggio clutch, as found in many single speed Piaggio / Vespa Mopeds. I.ex. Bravo, Ciao, Citta, Si, Grillo etc.
Пікірлер: 67
@Mrremusakajack2 ай бұрын
Thanks 🙏 finally figured out my problem is with the washer between the flywheel cus that one Is engaging the bolt that goes through . Hope I find it . 😂
@jammam45984 жыл бұрын
Thanks for the videos, I rebuilt my MS50 motor with your help. I'm now working on a Vespa Bravo and it's great to find you here as well!
@WesleySnyder4 жыл бұрын
great info. i just broke my clutch and now i understand how it works. thank you
@bestofblocket6 жыл бұрын
Really like your videos! Haven't been playing with moped for 20 years, and just bought myself an early ciao model that I'm going to renovate. Cheers from Skåne, Sweden!
@vnsworkshop99615 жыл бұрын
Thanks, Ciao is a little toys but funny to work with, and interesting that also the stock engine can be easy gain some power .
@heinzstucki30692 жыл бұрын
Sehr gutes Video, gut erklärt. Danke Gruss v. Heinz aus der Schweiz
@MopedFactory5 жыл бұрын
Keep up the good work 👍
@TheZemun5 жыл бұрын
@Carsten Lorenzen Dear Sir THAN YOUk TONS for this perfect info and especially for that nut that need to be direct outward the housing ... Thanks .
@glecas5 жыл бұрын
Please make a similar video covering the variomatic both front and rear! :-)
@gustavrybka2 жыл бұрын
Tak for at du laver så uddybede videoer, jeg viste ikke så meget om knallert inden jeg så dig. Nu kan jeg sætte nye fjedre i min ciao🙏
@tonvoka27424 жыл бұрын
Very very clear, thank you very much
@kaxjr34032 жыл бұрын
Great video
@domi93535 жыл бұрын
You are a Ehrenmann
@mariolaghezza2414 жыл бұрын
hello Caster Lorenzen. this video was very useful. I saw many Italian videos that talked about moped clutch but all of these aren't very Precise. For this reason it was not clear to me how to reassemble the moped clutch and therefore my piaggio ciao could not start. Thank you very much.
@luukkoekje81156 жыл бұрын
Hi can u make a video about the rear wheel drive of a piaggio moped
@stijndevos15664 жыл бұрын
my vespa ciao does not accelerate quickly and the springs at the starting clutch are worn out should i replace it? Does this make a difrence with acceleration ? Because i bought polini set blue green and metal color en the green doest work en the metal color doesnt accelerate quik
@timothytim10535 күн бұрын
Can someone please explain how the starting pads are to be mounted? Everyone says they should be mounted in the "correct" direction, but they look the same from both angles? How do you get them in the right position?
@CarstenLorenzen12V5 күн бұрын
@@timothytim1053 mount them, so that they look like in this video.
@TomekTomaszewski-dd8yo Жыл бұрын
Hi. Mam piaggio ciao ,przy kreceniu pedalami niekreci silnikiem w efrkcie czego niepdpala ,ktore przeglo mam wzmienic?
@oddballmedia Жыл бұрын
Super video. Tak for det. Har netop fået mig en Bravo. Der er lidt der skal fixes på den. Hvor stramt skal beltet være? Og jeg mangler lys i tomgang, kommer kun på omdrejninger?
@CarstenLorenzen12V Жыл бұрын
Den skal være rimelig stram, hvis man kører tunet. Men ellers så løs som mulig, uden at den glider 😉 Ja lysstyrken følger motor omdrejninger. For store pærer eller dårlige forbindelser, gør problemet værre.
@oddballmedia Жыл бұрын
@@CarstenLorenzen12V mange tak for svar 👌
@alessandropezzella92746 жыл бұрын
Wow
@poliniofficial3 жыл бұрын
You mention that Newfren clutch segments are good quality and then you say something about Malossi, but I can't hear if you say that one should or should not buy Malossi segments. Could you specify please?
@CarstenLorenzen12V3 жыл бұрын
Don't buy the Malossi. Mine held up for 50 km. The newfren actually also died a few weeks ago. But managed to go over 500 km. I use it on a 46 mm Polini, it's great torque is hard on the segments.
@kaluram-hb9co3 жыл бұрын
I want this clutch
@ondrejborovec97905 жыл бұрын
Great video! Can you please write the size of the bearing?
@CarstenLorenzen12V5 жыл бұрын
Thanks. The bearing number is HK1622 - measures 16x22x22 mm.
@Crysomemore234 жыл бұрын
Do you have an idea what can cause clutch vibrations at high revs? I tried to revv it on a side stand and touched it with a screwdriver it’s way too much. when I took the clutch apart, there no damage but starting clutch is missing 2mm off the pad on one side(crack). Could it be the bad weight distribution when rotating at high revs? I’ve got an old bravo variator version. Btw I like your videos big time!
@skentox43417 ай бұрын
du hörst dich an wie Lothar Matthäus
@CarstenLorenzen12V7 ай бұрын
Ouch..
@skentox43417 ай бұрын
;) 🤗 ein bischen hast du mich an ihn erinnert @@CarstenLorenzen12V natürlich nur wenn er Englisch spricht....... LG
@CarstenLorenzen12V7 ай бұрын
@@skentox4341 so lange es nicht sein Intellekt war 😉
@protagonistyuna55824 жыл бұрын
What happens when i put the washer wrongly and run the bike...
@CarstenLorenzen12V4 жыл бұрын
The clutch gets locked so the bike can't idle, and the thread for the flywheel puller can get damaged.
@kv92902 жыл бұрын
Hello, i might have an older version of the Ciao. And i can't pull the engine to the back like you do at 4:35 , what could i do ?
@kv92902 жыл бұрын
I managed to do it, i just had to pull it without losening anything. Thanks for the video
@Adam-ge3lk2 жыл бұрын
Hello Carsten! I have a problem on my non-variomativ ciao where I can’t get my clutch bell/basket off. It slides around nicely on the crank but when I slide it towards the end it suddenly stops, like there is a jack or similar on the crank. I have tried using gentle force and filing quite a bit on the crank but no success, any idea? Thanks, Adam,
@CarstenLorenzen12V2 жыл бұрын
Hi, sadly no good idea. There must be something that holds the clutchplate in place. Maybe a worn ridge/edge on the crank. Have you tried with a puller?
@Adam-ge3lk2 жыл бұрын
@@CarstenLorenzen12V No I have not tried a puller, do you think I should keep filing or try with pressure?
@CarstenLorenzen12V2 жыл бұрын
@@Adam-ge3lk hard to say, you are on your own now 😁
@laurentiugasca22135 жыл бұрын
Hello
@protagonistyuna55824 жыл бұрын
My piaggio ciao starts but dont run..maybe my clutch shoes is the problem???what do you think??thank u
@dannyvanderklei84833 жыл бұрын
Check the bearing behind te egnition-spools. When they leak, the moped wont drive. I just fixed that problem this week with exact the same problem as yours. When te clutch-shoes are not working, the moped wont start either.
@Toffli4ever5 ай бұрын
Wie hasst du sie wieder angezogen
@CarstenLorenzen12V5 ай бұрын
Polrad mit großem Schraubenzieher blockieren. Mutter ca 20-25 Nm spannen.
@SirCharles.5 жыл бұрын
I have a single speed Ciao and I tried to use the Malossi clutch springs but my engine seems not strong enough to use even the weakest springs. It will just slip and take too long to grab. I'm still not sure why it does not spin up faster, weak revs in low end. So I want to know if these Malossi springs can work with a stock original engine? If they can, then I must have some sort of issue with my modified engine. But for now I am using the original springs with drilled lighter shoes and that works fairly well.
@CarstenLorenzen12V5 жыл бұрын
The Malossi springs are very stiff. The green Polinis are the hardest i would run on a stock cylinder and setup. The drilled holes plus malossi springs put you in the 5000 rpm range before it starts to grip.
@SirCharles.5 жыл бұрын
@@CarstenLorenzen12V ok thanks for the info! I have a 43mm Malossi cylinder setup and even with that I can't get the lightest Malossi springs to grab quick enough. I have tried a lot of things already but it still has weak low end. I think it is an ignition issue so I'm going to try replacing the coil and magneto next, maybe the lighter late-model flywheel will help too. I'd also like to try electronic ignition, but there's no cheap option for that.
@mortenvestergaard21773 жыл бұрын
Hej. Hvor køber du nyt nåleleje og foring? Where do you buy the bearing set?
@CarstenLorenzen12V3 жыл бұрын
Hej. Det kan fås ved JMPB. Er ikke sikker på hvad du mener med foring?
@mortenvestergaard21773 жыл бұрын
@@CarstenLorenzen12V bøsningen inde i lejet = foring men det er jo en bøsning. Fandt begge dele. Tak for hjælpen.
@jesseark14 жыл бұрын
Do you have a link for a multi springs that you show in your video
@CarstenLorenzen12V4 жыл бұрын
Jmpbparts.com has them search for ciao springs polini.
@cocomartinez17095 жыл бұрын
cual es el ancho de la correa?
@CarstenLorenzen12V5 жыл бұрын
The width of the belt? It's 9,7 mm or close to that. Fitting standard belts are XPZ / SPZ / AVX10.
@tomkutscher15556 ай бұрын
Hallo, ich kriege diese vedammte Mutter bei 4:10 nicht ab,
@timkole20025 жыл бұрын
The netherlands
@CarstenLorenzen12V5 жыл бұрын
Denmark?
@jhhlu90884 жыл бұрын
schwizer
@CarstenLorenzen12V4 жыл бұрын
No i don't sweat alot?
@TheDatpussy3 жыл бұрын
Why is my vespa ciao clutch stuck then, if i have that washer facing correctly?